Page 4313 of 5135

C52361DLC3
FI0534
−
DIAGNOSTICS ECD SYSTEM (1CD −FTV)(From September, 2003)
05 −289
AVENSIS Supplement (RM 1045E)
S Freeze frame data
Freeze frame data records the engine conditions when a
malfunction is detected. When troubleshooting, freeze
frame data can help determine if the vehicle was running
or stopped, if the engine was warmed up or not, if the air −
fuel ratio was lean or rich, and other data from the time the
malfunction occurred.
2. CHECK DLC3
(a) The v ehicle’s ECM uses t he I SO 9 1 41− 2( Eur o −OBD)
communication protocol. The terminal arrangement of
the DLC3 complies with ISO 1503 1− 03 and matches the
ISO 9 141− 2 format.
SymbolTerminal No.NameReference TerminalResultCondition
SIL7Bus ”+” line5− Signal groundPulse generationDuring transmission
CG4Chassis groundBody ground1 or lessAlways
SG5Signal groundBody ground1 or lessAlways
BAT16Battery positiveBody ground9to 14VAlways
HINT:
Connect the cable of the hand −held tester to the DLC3, turn the
ignition switch to ON and attempt to use the hand −held tester.
If the screen displays UNABLE TO CONNECT TO VEHICLE,
a problem exists in the vehicle side or the tester side.
S If the communication is normal when the tool is connected
to another vehicle, inspect the DLC3 on the original ve-
hicle.
S If the communication is still impossible when the tool is
connected to another vehicle, the problem is probably in
the tester itself, so consult the Service Department listed
in its instruction manual.
3. INSPECT BATTERY VOLTAGE Battery voltage: 11 to14V
If voltage is below 11 V, recharge the battery before proceeding.
4. CHECK CHK ENG
(a) The CHK ENG comes on when the ignition switch is turned to the ON position and the engine is not running.
HINT:
If the CHK ENG is not illuminated, troubleshoot the combination
meter circuit (see page 05 −299).
(b) When the engine is started, the CHK ENG should turn off. If the CHK ENG illuminates again, the diagnosis system
has detected a malfunction or abnormality in the system.
Page 4314 of 5135

054KK−10
A66714
E13
E12E10
E9
− DIAGNOSTICSECD SYSTEM (1CD−FTV)(From September, 2003)
05−285
AVENSIS Supplement (RM1045E)
TERMINALS OF ECM
HINT:
Each ECM terminal’s standard voltage is shown in the table below.
In the table, first follow the information under ”Symbols (Terminals No.)”. Look under ”Tester Connection” for
the terminals to be inspected. The standard voltage between the terminals is shown under ”STD Voltage
(V)”.
Use the illustration above as a reference for the ECM terminals.
Symbols (Terminals No.)Wiring ColorTerminal DescriptionConditionSTD Voltage (V)
BATT (E10−2)−E1(E12−7)B−Y−BR
Battery (for measuring the
battery voltage and for the
ECM memory)
Always9to14
IGSW (E9−9)−E1(E12−7)B−W−BRIgnition switchIgnition switch ON9to14
+B (E9−1)−E1(E12−7)B−W−BRPower source of ECMIgnition switch ON9to14
MREL(E98)E1(E127)GRBRECDrelayIgnition switch ON9to14MREL(E9−8)−E1(E12−7)GR−BRECD relayIgnition switch OFF0to1.5
VC (E13−18)−E1(E12−7)R−W−BRPower source of sensor
(a specific voltage)Ignition switch ON4.5 to 5.5
VPA(E922)EPA(E928)GY
Accelerator pedal position
sensor(fortheengine
Ignition switch ON, Accelerator ped-
al fully released0.5 to1.1
VPA(E9−22)−EPA(E9−28)G−Ysensor (for the engine
control)Ignition switch ON, Accelerator ped-
al fully depressed2.6 to 4.5
VPA2(E923)EPA2(E929)WY
Accelerator pedal position
sensor(forthesensor
Ignition switch ON, Accelerator ped-
al fully released1.2 to 2.0
VPA2 (E9−23)−EPA2 (E9−29)W−Ysensor (for the sensor
malfunction detection)Ignition switch ON, Accelerator ped-
al fully depressed3.4 to 5.3
VCPA (E9−26)−EPA (E9−28)B−Y
Power source of acceler-
ator pedal position sensor
(for VPA)
Ignition switch ON4.5 to 5.5
VCP2 (E9−27)−EPA2 (E9−29)B−Y
Power source of acceler-
ator pedal position sensor
(for VPA2)
Ignition switch ON4.5 to 5.5
VG (E12−24)−EVG (E12−32)G−L−YMass air flow meterIdling0.5 to 3.4
THA (E13−31)−E2 (E13−28)G−R−BRIntake air temperature
sensorIdling, Intake air temperature at
20˚C (68˚F)0.5 to 3.4
THIA (E13−20)−E2 (E13−28)GR−BRIntake air temperature
sensorIdling, Intake air temperature at
80˚C(176˚F)0.3 to 0.9
THW (E13−19)−E2 (E13−28)B−W−BREngine coolant tempera-
ture sensorIdling, Engine coolant temperature
at 80˚C(176˚F)0.2 to1.0
Page 4315 of 5135

05−286
−
DIAGNOSTICS ECD SYSTEM (1CD −FTV)(From September, 2003)
AVENSIS Supplement (RM 1045E)
Symbols (Terminals No.)
STD Voltage (V)
Condition
Terminal Description
Wiring Color
STA (E9 −7) − E1 (E 12− 7)B −Y − BRStarter signalCranking6.0 or more
#1 (E 13− 24) − E1 (E 12− 7)
#2 (E 13− 23) − E1 (E 12− 7)
#3 (E 13− 22) − E1 (E 12− 7)
#4 (E 13− 21) − E1 (E 12− 7)G −W − BR
W −R − BR
R −W − BR
W −L − BR
InjectorIdlingPulse generation
(See page 05 −368)
G+ (E 12− 23) −G− (E 12− 31)P −LCamshaft position sensorIdlingPulse generation
(See page 05 −384)
NE+ (E 13− 27) −NE −(E 13− 34)G −RCrankshaft position sen-
sorIdlingPulse generation
(See page 05 −38 1)
STP(E 10 15)E 1(E 12 7)G WBRStopla ps itch
Ignition switch ON, Brake pedal de-
pressed7.5 to 14
STP (E 10−1 5)−E1 (E 12− 7)G −W− BRStop lamp switchIgnition switch ON, Brake pedal re-
leased0to 1.5
ST 1(E10 14)E 1(E 12 7)G WBRStoplampswitchBrake pedal depressed0to 1.5ST 1− (E10−1 4)−E1 (E 12− 7)G −W− BRStoplampswitch
(opposite to STP)Brake pedal released7.5 to 14
TC (E9 −11)− E1 (E 12− 7)W −L −BRTerminal TC of DLC 3Ignition switch ON9to 14
W(E9 12)E 1(E 12 7)WBRCheck engine warningCHK ENG illuminated0to3W (E9 −12)−E1 (E 12− 7)W −BRCheckenginewarning
light (CHK ENG)CHK ENG not illuminated9to 14
SPD (E 10−1 7)−E1 (E 12− 7)V −W −BRSpeed signal from com-
bination meterIgnition switch ON, Rotate driving
wheel slowlyPulse generation
(See page 05 −408)
SIL (E9 −18)−E1 (E 12− 7)W −G −BRTerminal SIL of DLC3Connect the hand −held tester to the
DLC3Pulse generation
Applied negative pressure of 40 kPa
(300 mmHg, 11.8 in.Hg)1.4 to 2.0
PIM (E 12− 28) −E2 (E 13− 28)W −R −BRTurbo pressure sensorSame as atmospheric pressure2.0 to 2.6PIM(E 12 28)E2(E13 28)W RBRTurbopressuresensor
Applied positive pressure of 69 kPa
(518 mmHg, 20.4 in.Hg)3.0 to 3.6
IREL(E9 10)E 1(E 12 7)YBREDUrelayIgnition switch OFF9to 14IREL (E9 −10)−E1 (E 12− 7)Y− BREDU relayIdling0to 1.5
TACH (E9 −4) −E1 (E 12− 7)GR −R −BREngine speedIdlingPulse generation
VCS (E 12− 2) −E2S (E 12−1 )R−W −BRCommon rail pressure
sensorIgnition switch ON4.5 to 5.5
PCR 1(E 13− 26) −E2 (E 13− 28)P −BRCommon rail pressure
sensor (main)Idling1.8 to 2. 1
PCR2 (E 13− 33) −E2 (E 13− 28)P −B −BRCommon rail pressure
sensor (sub)Idling1.2 to 1.5
GREL(E9 15)E 1(E 12 7)RBRGlowplugrelayCranking9to 14GREL(E9 −15)−E1 (E 12− 7)R −BRGlowplug relayIdling0to 1.5
THF (E 13− 29) −E2 (E 13− 28)L −BRFuel temperature sensorIgnition switch ON0.5 to 3.4
ALT (E 13− 8) −E1 (E 12− 7)B −L − BRGenerator (Alternator)
duty signalIdlingPulse generation
PCV+ (E 13− 2) −PCV −(E 13−1 )LG −R −LGSuction control valveIdlingPulse generation
(See page 05 −429)
PRD (E 13− 32) −E1 (E 12− 7)R −L − BRPressure relief valve drive
signalIgnition switch OFF4 to 6.5
INJF (E 13− 25) −E1 (E 12− 7)R −B −BREDUIdlingPulse generation
(See page 05 −368)
VN (E 13−1 0)−E1 (E 12− 7)W −BRVRV (for VN turbochar-
ger)Ignition switch ONPulse generation
(See page 05 −312)
AF2+ (E 10− 35) −E1 (E 12− 7)B −BRA/FsensorIgnitionswitchON3.0 to 3.6
AF2 −(E 10− 34) −E1 (E 12− 7)W −BRA/F sensorIgnition switch ON2.7 to 3.3
HAF2 (E 12− 5) −E1 (E 12− 7)L− R −BRA/F sensor heater duty
signalIdlingPulse generation
FIV (E 13− 3) −E1 (E 12− 7)L− R −BRExhaust fuel addition in-
jectorEngine warmed up, Idling, Every 1
to 2 minutesPulse generation
(See page 05 −470)
Page 4316 of 5135

−
DIAGNOSTICS ECD SYSTEM (1CD −FTV)(From September, 2003)
05 −287
AVENSIS Supplement (RM 1045E)
Symbols (Terminals No.)
STD Voltage (V)
Condition
Terminal Description
Wiring Color
THCO (E 12− 30) −E2 (E 13− 28)B −Y −BRExhaustgas temperatureEnginewarmedupIdling46to49THCI (E 12− 22) −E2 (E 13− 28)B −BR
Exhaustgastemperature
sensorEngine warmed up, Idling4.6 to 4.9
EGRS (E 12− 3) −E2 (E 13− 28)R −L − BREGR valve duty signalEngine warmed up, IdlingPulse generation
(See page 05 −393)
EGLS (E 12− 33) −E2 (E 13− 28)R −BREGR valve position sen-
sorIgnition switch ON0.6 to 1.4
PEX (E 12− 20) −E2 (E 13− 28)W −BRDifferential pressure sen-
sorIgnition switch ON, differential pres-
sure at 0 kPa1.2 to 1.8
VLU(E 12 29)E2(E13 28)LWBRIntake shutter(throttle
Ignition switch ON, Intake shutter
(throttle valve) fully opened3.0 to 4.0
VLU (E 12− 29) −E2 (E 13− 28)L−W− BRIntakeshutter(throttle
valve) position sensorIgnition switch ON, Intake shutter
(throttle valve) fully closed0.4 to 1.0
LUSL (E 12− 4) −E2 (E 13− 28)G −R −BRIntake shutter (throttle
valve) duty signalEngine warmed up, Racing enginePulse generation
(See page 05 −403)
Page 4317 of 5135

05DVW−02
−
DIAGNOSTICS ECD SYSTEM (1CD −FTV)(From September, 2003)
05 −277
AVENSIS Supplement (RM 1045E)
REGISTRATION
NOTICE:
S The injector compensation code will be required to register with the ECM when replacing injec-
tors or the ECM.
S If an incorrect injector compensation code was registered with the ECM, it may rattle the engine
assembly or the engine idling may become rough. In addition, it may become a cause of engine
failure or shorten the life of the engine.
1 . If you replace the ECM with a new one, register all the injector compensation codes with the
new ECM as follows:
(a) Prior to replacing the ECM, read all the compensation codes stored in the existing ECM using the hand−held tester, and then write them down (see page 05 −273).
(b) After replacing the ECM, enter the written compensation codes into the ECM using the hand −held tes-
ter (see page 05 −277).
(c) Turn the ignition switch to OFF and turn the hand −held tester OFF, then wait for 30 seconds or more.
(d) Turn the ignition switch to ON and turn the hand −held tester ON, then clear DTC P 160 1using the
hand −held tester (see page 05 −290).
HINT:
SIn order to optimize the injector’s fuel injection characteristic, the ECM compensates the injection dura-
tion by each cylinder. The ECM stores and uses compensating data in the form of a 30 −digit −alphanu-
meric value that is imprinted on the head portion of each injector as the injector compensation code.
SIf you installed a new injector, its own injector compensation code is needed to register with the ECM.
Also, if you replaced the ECM, the compensation codes of all the injectors are needed to register be-
cause the new ECM dose not have the codes until they are registered.
SOnce the ECM is replaced, DTC P 160 1will be present when turning the ignition switch to ON. This
is to inform you that the injector compensation codes are required to register with the ECM. In order
to clear the DTC, register the compensation codes first, then turn the ignition switch to OFF and wait
for 30 seconds or more.
Page 4318 of 5135
Register the injector compensation code
(Setting the injector compensation code is end)other cylinders? Will you set injector
compensation codes to the
A91212
Process of setting injector compensation code(s): 05−278
− DIAGNOSTICSECD SYSTEM (1CD−FTV)(From September, 2003)
AVENSIS Supplement (RM1045E)
2. SET INJECTOR COMPENSATION CODE
(a) Connect the hand−held tester to the DLC 3.
(b) Turn the ignition switch to ON.
(c) Turn the hand−held tester ON.
NOTICE:
Do not start the engine in this operation.
HINT:
Injector compensation code is imprinted on the head portion of
the injector.
Page 4319 of 5135
A80985
A66061
A66062
A66068
A66069
− DIAGNOSTICSECD SYSTEM (1CD−FTV)(From September, 2003)
05−279
AVENSIS Supplement (RM1045E)
(d) Enter ”DIAGNOSIS / OBD/MOBD / DIAGNOSTIC MENU
ECD” and select the item ”INJECTOR COMP”.
(e) Press the ”ENTER” button on the hand−held tester.
(f) Press the ”Enter” button again.
(g) Select ”SET COMP VALUE” and press the ”ENTER” but-
ton.
(h) Press the ”ENTER” button.
(i) Select a cylinder number which you want to register the
compensation code.
(j) Press the ”ENTER” button.
Page 4320 of 5135
A66070
A66071
A66072
A66073
05−280
− DIAGNOSTICSECD SYSTEM (1CD−FTV)(From September, 2003)
AVENSIS Supplement (RM1045E)
(k) Input the compensation code (30−digit−alphanumeric
value).
(l) After inputting, press the ”ENTER” button.
(m) Press the ”ENTER” button again.
(n) Confirm the injection compensation code displayed on
the hand−held tester.
NOTICE:
Be careful not to register a wrong compensation code to
the ECM. If a wrong code is set to the ECM, rough idling or
engine rattling may result. In addition, it may become a
cause of engine failure or shorten the life of the engine.
HINT:
SThe code shown in the illustration is an example.
SIf a wrong compensation code was entered on the hand−
held tester, select the ”NO” button to correct the error
(Back to step [g]).
(o) Press the ”YES” button to set the code to the ECM.
(p) Wait until the next screen comes up.