Page 633 of 5135
05±532
± DIAGNOSTICSECD SYSTEM (1CD±FTV)
AVENSIS REPAIR MANUAL (RM1018E)
(c) Clearing the DTCs not using the hand±held tester:
(1) Disconnect the battery terminal or remove the EFI
and ETCS fuses from the engine room R/B for more
than 60 seconds.
4. FAIL±SAFE CHART
If any of the following codes are recorded, the ECM enters the fail±safe mode.
DTC No.Fail±Safe OperationFail±Safe Deactivation Conditions
P0087VTA is fixed at 10 %Ignition switch OFF
P0088VTA is fixed at 10 %Ignition switch OFF
P0093After fail safe driving control is performed for 1 minute, en-
gine stallsIgnition switch OFF
P0095
P0097
P0098
Intake air temp. is fixed at 145C (293F)Return to normal condition
P0105
P0107
P0108
Turbo pressure is set at fixed valueReturn to normal condition
P0115
P0117
P0118
When fuel temp. sensor operates normal and intake air
temp. is less than 15C (59F), value of fuel temp. sensor
is substituted
When fuel temp. sensor operates normal and intake air
temp. is more than 20C (68F), value is fixed at 120C
(248F)
When the fuel temp. sensor is abnormal, value is fixed at
40C (104F)
Return to normal condition
P0168Output limitReturn to normal condition
P0180
P0182
P0183
Fuel temp. is fixed at 40C (104F)Return to normal condition
P0190
P0191
P0192
P0193
VTA is fixed at 10 %Ignition switch OFF
P0200VTA is fixed at 25 %Ignition switch OFF
P0335Output limitReturn to normal condition
P0488VTA is fixed at 25 %Ignition switch OFF
P0500Vehicle speed is fixed at 0 km/h (0 mph)Vehicle speed less than 10 km/h (6 mph)
P1229VTA is fixed at 10 %Ignition switch OFF
P1271VTA is fixed at 25 %Ignition switch OFF
P1272VTA is fixed at 25 %Ignition switch OFF
P2120
P2122
P2123
P2125
P2127
P2128
P2138
Output limitIgnition switch OFF
5. CHECK FOR INTERMITTENT PROBLEMS
Hand±held tester only:
By putting the vehicle's ECM in the check mode, the 1 trip detection logic is possible instead of the 2 trip
detection logic, and the sensitivity to detect faults is increased. This makes it easier to detect intermittent
problems.
(a) Clear the DTCs (See step 2).
(b) Set the check mode (See step 3).
Page 634 of 5135
±
DIAGNOSTICS ECD SYSTEM(1CD±FTV)
05±533
AVENSIS REPAIR MANUAL (RM1018E)
(c)Perform a simulation test (See page 01±22).
(d)Check the connector and terminal (See page 01±32).
(e)Wiggle the harness and connector (See page 01±32).
6. DATA LIST
HINT:
Using the DATA LIST displayed by the hand±held tester, you can read the value of the switches, sensors,
actuators and so on without parts removal. Reading the DATA LIST as a first step of troubleshooting is one
method to shorten diagnostic time.
NOTICE:
The values given below for ºNormal Conditionº are representative valu\
es. A vehicle may still be nor-
mal even if its value differs from those listed here. Do not solely depend \
on the ºNormal Conditionº
here when deciding whether a part is faulty or not.
(a) Warm up the engine.
(b) Turn the ignition switch OFF.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch ON.
(e) Push the ºONº button of the hand±held tester.
(f) Select the item ºDIAGNOSIS / OBD/MOBD / DATA LISTº.
(g) According to the display on tester, read the ºDATA LISTº.
Hand±held Tester DisplayMeasurement Item/Range
(Display)Normal Condition *Diagnostic Note
INJ VOLUMEInjection volume/
Min.: 0 mm3, Max.: 1279.98 mm3Idling: 3 to 10 mm3
INJ TIMINGInjection timing/
Min.: 0 CA, Max.: 51 CAIdling: ±1 to 5 CA
ENGINE SPDEngine speed/
Min.: 0 rpm, Max.: 16383.75 rpmIdling: 750 to rpm
MAF
Air flow rate from MAF sensor sta-
tus/
Min.: 0 gm/s, Max.: 655.35 gm/sIdling: 3.2 to 4.7 gm/s
Running without load (2,500
rpm): 13.1 to 18.9 gm/s
If the value is Approximately 0.0
gm/s:
Mass air flow meter power
source circuit open
VG circuit open or short
If the valve is 160 gm/s or more:
E2G circuit open
PIM
Absolute pressure inside intake
manifold/ Min.: 0 kPa, Max.: 255
kPa
Idling: 85 to 110 kPa
COOLANT TEMPCoolant temperature/
Min.: ±40 C, Max.: 215 CAfter warming up: 80 to 95 C (176
to 203
INTAKE AIRIntake air temperature/
Min.: ±40 C, Max.: 215 CEquivalent to Ambient Temp.
If the value is º±40 Cº or º140
Cº, sensor circuit is open or
shorted
FUEL TEMPFuel temperature status/
Min.: ±40 C, Max.: 215 CActual fuel temp.
shorted.
ACCEL POSITIONAccel position status/
Min.: 0 %, Max.: 100 %
Accelerator pedal released:
10 to 22 %
Accelerator pedal depressed:
52 to 90 %
Read the value with ignition switch
ON (Do not start engine).
VEHICLE SPDVehicle speed/
Min.: 0 km/h, Max.: 255 km/hActual vehicle speedSpeed indicated on speedometer
THROTTLE POSThrottle step position status/
Min.: 1 step, Max.: 255 stepThrottle fully closed: 1 step
Throttle fully open: 255 stepRead the value with ignition switch
ON (Do not start engine).
COMN RAIL PRESSCommon rail pressure status/
Min.: 0 MPa, Max.: 255 MPaIdling: 30 to 40 MPa
Page 635 of 5135
05±534
± DIAGNOSTICSECD SYSTEM (1CD±FTV)
AVENSIS REPAIR MANUAL (RM1018E)Hand±held Tester DisplayDiagnostic Note Normal Condition * Measurement Item/Range
(Display)
AMBI TEMP SENS
Ambient temperature sensor sta-
tus/
Min.: ±40 C, Max.: 215 C
Actual atmosphere
If the value is º±40 Cº or º140
Cº, sensor circuit is open or
shorted.
INJ VOL FB #1
Revised injection volume of the
cylinder 1/
Min.: ±10 mm
3, Max.: 40 mm3Idling: ±3.0 to 3.0 mm3
INJ VOL FB #2
Revised injection volume of the
cylinder 2/
Min.: ±10 mm
3, Max.: 40 mm3Idling: ±3.0 to 3.0 mm3
INJ VOL FB #3
Revised injection volume of the
cylinder 3/
Min.: ±10 mm
3, Max.: 40 mm3Idling: ±3.0 to 3.0 mm3
INJ VOL FB #4
Revised injection volume of the
cylinder 4/
Min.: ±10 mm
3, Max.: 40 mm3Idling: ±3.0 to 3.0 mm3
PUMP VCM ANGLEPump vacuum angle status/
Min.: 0 CA, Max.: 255 CAIdling: 70 to 90CA
M±INJ/PILOT ONM±INJ/PILOT ON/
Min.: 0 us, Max.: 65,535 usIdling: 600 to 1,200 us
M±INJ/PILOT OFFM±INJ/PILOT OFF/
Min.: 0 us, Max.: 65,535 usIdling: 0 us
PILOT±INJPilot±Injection/
Min.: 0 us, Max.: 65,535 usIdling: 400 to 700 us
INJ FB VALUE
Injection volume feedback learning
value/
Min.: ±10 mm
3, Max.: 9,092 mm3Idling: ±4.0 to 4.0 mm3
STOP LIGHT SWStop light switch/
ON or OFFBrake pedal depressed: ON
Brake pedal released: OFF
STARTER SIGStarter signal/ ON or OFFCranking: ON
A/C CUT SIGA/C cut signal/ ON or OFFA/C ON: OFF
EGR SYSTEMEGR system status/ ON or OFFIdling: ON
ACCEL OPEN SWAccel open switch/ ON or OFFAccelerator pedal fully opened:
ON
CHECK MODECheck mode/ ON or OFFCheck mode ON: ON
EGR STEP POSEGR step position status/
Min: 0 step, Max: 125 stepIdling: 0 to 125 step
*: If no conditions are specifically stated for ºldlingº, it means the A/C switch is OFF and all accessory switches
are OFF.
7. ACTIVE TEST
HINT:
Performing the ACTIVE TEST using the hand±held tester allows the relay, VSV, actuator and so on to oper-
ate without parts removal. Performing the ACTIVE TEST as a first step of troubleshooting is one of the meth-
ods to shorten diagnostic time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Warm up the engine.
(b) Turn the ignition switch OFF.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch ON.
(e) Push the ºONº button of the hand±held tester.
(f) Select the item ºDIAGNOSIS / OBD/MOBD / ACTIVE TESTº
Page 636 of 5135
± DIAGNOSTICSECD SYSTEM (1CD±FTV)
05±535
AVENSIS REPAIR MANUAL (RM1018E)
(g) According to the display on tester, perform the ºACTIVE TESTº.
Hand±held Tester DisplayTest DetailsDiagnostic Note
EGR STEP POS
[Test Details]
Change step of EGR motor
Min: 0 step, Max: 125 step
TC/TE1
[Test Details]
Connect the TC and TE1
ON or OFF
FUEL LEAK TEST
[Test Details]
Fuel leak test
ON or OFF
INJECTOR CUT #1
[Test Details]
Injector cut #1
ON or OFF
INJECTOR CUT #2
[Test Details]
Injector cut #2
ON or OFF
INJECTOR CUT #3
[Test Details]
Injector cut #3
ON or OFF
INJECTOR CUT #4
[Test Details]
Injector cut #4
ON or OFF
Page 637 of 5135
Are you read the injector
A81230
Reading flowchart: 05±536
± DIAGNOSTICSECD SYSTEM (1CD±FTV)
AVENSIS REPAIR MANUAL (RM1018E)
8. READ INJECTOR COMPENSATION CODE
HINT:
This operation is useful when confirming the compensation
code of each injector or when DTC P1601 is present.
(a) Connect the hand±held tester to the DLC 3.
(b) Turn the ignition switch ON.
(c) Turn the main switch of the hand±held tester ON.
NOTICE:
Do not start the engine in this operation.
Page 638 of 5135
A80985
A66061
A66063
A66064
A66065
± DIAGNOSTICSECD SYSTEM (1CD±FTV)
05±537
AVENSIS REPAIR MANUAL (RM1018E)
(d) Enter ºDIAGNOSIS / OBD/MOBD / DIAGNOSTIC MENU
ECDº and select the item ºINJECTOR COMP.º
(e) Press the ºENTERº button on the hand±held tester.
(f) Press the ºENTERº button again.
(g) Select ºREAD COMP VALUEº and press the ºENTERº
button.
(h) Select a cylinder number which you want to read the com-
pensation code.
(i) Press the ºENTERº button.
(j) Wait until the next screen comes up.
Page 639 of 5135
A66066
A66067
05±538
± DIAGNOSTICSECD SYSTEM (1CD±FTV)
AVENSIS REPAIR MANUAL (RM1018E)
(k) Confirm the 30±digit±alphanumeric code which is dis-
played on the hand±held tester. This is the injection com-
pensation code for the cylinder.
HINT:
The code shown in the illustration is an example.
(l) Press the ºENTERº button to exit this screen.
(m) Press the ºNOº button to complete the confirmation.
HINT:
If you want to read other compensation codes for other
cylinders, press the ºYESº button instead of ºNO.º
By pressing the ºNOº button, the hand±held tester returns
to the ºDIAGNOSTIC MENU ECDº screen.
Page 640 of 5135
Register the injector compensation code
(Set the injector compensation code)other cylinders?Register the injector compensation code
(Set the injector compensation code)other cylinders?
A81231
Setting flowchart:
± DIAGNOSTICSECD SYSTEM (1CD±FTV)
05±539
AVENSIS REPAIR MANUAL (RM1018E)
9. SET INJECTOR COMPENSATION CODE
HINT:
This operation must be done when replacing the ECM or the in-
jectors.
(a) Connect the hand±held tester to the DLC 3.
(b) Turn the ignition switch ON.
(c) Turn the main switch of the hand±held tester ON.
NOTICE:
Do not start the engine in this operation.