Page 4737 of 5135

C68341
C52593F40212
SST
C68582F40213
F40214
SST
SST(A)
F02277
SST
(A) 30−10
− DRIVE SHAFT / PROPELLER SHAFTFRONT DRIVE SHAFT (2AZ−FSE)
AVENSIS Supplement (RM1045E)
28. INSTALL CASE SUB ASSY, DRIVE SHAFT BEARING
SNAP RING (RH DRIVE SHAFT)
(a) Using a screwdriver, install a new bearing case snap ring.
29. INSTALL DRIVE SHAFT BEARING CASE SUB ASSY
(RH DRIVE SHAFT)
(a) Using SST and a press, install the drive shaft bearing
case to the inboard joint assy RH.
SST 09527−10011, 09710−04081
NOTICE:
Bearing should be installed completely.
(b) Using a snap ring expander, install a new drive shaft hole
snap ring.
30. INSTALL FRONT DRIVE SHAFT DUST COVER (RH
DRIVE SHAFT)
(a) Using SST and a press, install a new drive shaft dust cov-
er.
SST 09726−40010, 09527−10011
Distance (A): 0.5 á0.5 mm (0.020 á0.020 in.)
NOTICE:
Be careful not to damage the dust cover.
31. INSTALL FRONT DRIVE SHAFT DUST COVER RH (RH
DRIVE SHAFT)
(a) Using SST and a press, install a new drive shaft dust cov-
er RH until the distance from the tip of the center drive
shaft to the drive shaft dust cover RH reaches the specifi-
cation, as shown in the illustration.
SST 09527−10011
Distance (A):110.5 á0.5 mm (4.350 á0.020 in.)
Page 4738 of 5135

C63297F45152
SST
W01994
Vinyl Tape
R10425
SSTHold
Turn
− DRIVE SHAFT / PROPELLER SHAFTFRONT DRIVE SHAFT (2AZ−FSE)
30−11
AVENSIS Supplement (RM1045E)
(b) Using SST and a press, install a new drive shaft dust cov-
er RH.
SST 09527−10011
NOTICE:
SDust cover should be installed completely.
SBe careful not to damage the dust cover.
32. INSTALL FRONT DRIVE SHAFT DUST COVER LH
(a) Using SST and a press, install a new drive shaft dust cover LH.
SST 09527−10011
NOTICE:
SDust cover should be installed completely.
SBe careful not to damage the dust cover.
33. INSTALL FRONT DRIVE SHAFT LH HOLE SNAP RING
(a) Install a new hole snap ring.
34. INSTALL OUTBOARD JOINT BOOT
HINT:
Before installing the boots, wrap the drive shaft spline with vinyl
tape to prevent the boots from being damaged.
(a) Install new parts to the outboard joint shaft assy in the fol-
lowing order.
(1) Outboard joint boot LH No.2 clamp
(2) Outboard joint boot
(3) Outboard joint boot LH clamp
(b) Pack the outboard joint shaft and boot with grease in the
boot kit.
Grease capacity:152 to162 g (5.4 to 5.7 oz.)
35. INSTALL FRONT AXLE OUTBOARD JOINT BOOT
CLAMP
(a) Hold the front drive shaft in a soft vise.
(b) Secure the 2 outboard joint boot clamps onto the boot.
(c) Place SST onto the outboard joint large boot clamp.
SST 09521−24010
(d) Tighten the SST so that the large clamp is pinched.
NOTICE:
Do not overtighten the SST.
Page 4739 of 5135

R10426
SST
F40646Distance
C86267
SSTHold
Turn 30−12
− DRIVE SHAFT / PROPELLER SHAFTFRONT DRIVE SHAFT (2AZ−FSE)
AVENSIS Supplement (RM1045E)
(e) Using SST, adjust the clearance of the large clamp.
SST 09240−00020
Clearance: 0.8 mm (0.031in.) or less
(f) Install the outboard joint boot LH clamp following the
same procedure as for the outboard joint boot LH No.2
clamp.
NOTICE:
When the measured value exceeds the specified value, re-
tighten the clamp.
36. INSTALL FRONT DRIVE SHAFT DAMPER LH
HINT:
Perform the above procedure only when reassembling the RH
side.
(a) Temporarily install a new damper clamp.
(b) Set the distance as described below.
Drive shaft typeDistance mm (in.)
RH212.0 á2.0
(8.35 á0.08)
LH168.0 á2.0
(6.61 á0.08)
(c) Install the damper clamp.
HINT:
Install the damper clamp to inboard joint side.
(1) Hold the front drive shaft in a soft vise.
(2) Secure the damper clamp onto the damper.
(3) Place SST onto the damper clamp.
SST 09521−24010
(4) Tighten the SST so that the damper clamp is
pinched.
NOTICE:
Do not overtighten the SST.
Page 4740 of 5135

C86268
SST
C67417
Matchmarks
G24058
− DRIVE SHAFT / PROPELLER SHAFTFRONT DRIVE SHAFT (2AZ−FSE)
30−13
AVENSIS Supplement (RM1045E)
(5) Using SST, adjust the clearance of the damper
clamp.
SST 09240−00020
Clearance: 0.8 mm (0.031in.) or less
NOTICE:
When the measured value exceeds the specified value, re-
tighten the clamp.
HINT:
SInstall the damper clamp to inboard joint side.
SPerform the above procedure only when reassembling
the RH side.
37. INSTALL FRONT DRIVE INBOARD JOINT ASSY LH
(a) Wrap the outboard joint shaft assy LH spline with vinyl
tape to prevent it from being damaged.
(b) Install new parts to the outboard joint shaft assy LH in the
following order.
(1) Inboard joint boot LH clamp
(2) Inboard joint boot
(3) Inboard joint boot LH No.2 clamp
(c) Place the beveled side of the tripod axial spline toward the
outboard joint.
(d) Align the match marks.
(e) Using a brass bar and hammer, tap in the tripod joint assy
to the drive shaft assy LH.
NOTICE:
SDo not tap the roller.
SBe sure to install the tripod joint assy in the correct
direction.
(f) Pack the inboard joint shaft and boot with grease in the
boot kit.
Grease capacity:170 to190 g (6.0 to 6.7 oz.)
(g) Using a snap ring expander, install a new shaft snap ring.
Page 4741 of 5135

C67413F45461
Matchmarks
C86269
SST
Hold
Turn
C86270SST
C91598
30−14
− DRIVE SHAFT / PROPELLER SHAFTFRONT DRIVE SHAFT (2AZ−FSE)
AVENSIS Supplement (RM1045E)
(h) Aligning the matchmarks, install the inboard joint assy LH
to the outboard joint shaft assy LH.
38. INSTALL FR AXLE INBOARD JOINT BOOT
(a) Install the inboard joint boot to the inboard joint assy LH and outboard joint shaft assy LH.
39. INSTALL FRONT AXLE INBOARD JOINT BOOT
CLAMP
(a) Install the inboard joint boot clamp.
(1) Hold the drive shaft in a soft vise.
(2) Secure the 2 inboard joint boot clamps onto the
boot.
(3) Place SST onto the inboard joint large boot clamp.
SST 09521−24010
(4) Tighten the SST so that the large clamp is pinched.
NOTICE:
Do not overtighten the SST.
(5) Using SST, adjust the clearance of the large clamp.
SST 09240−00020
Clearance: 0.8 mm (0.031in.) or less
NOTICE:
When the measured value exceeds the specified value, re-
tighten the clamp.
(b) Install the inboard joint boot LH clamp following the same
procedure as for the inboard joint boot LH No.2 clamp.
40. INSPECT FRONT DRIVE SHAFT
(a) Check that there is no excessive play in the radial direc-
tion of the outboard joint.
(b) Check that the inboard joint slides smoothly in the thrust
direction.
(c) Check that there is no excessive play in the radial direc-
tion of the inboard joint.
(d) Check the boots for damage.
NOTICE:
Keep the drive shaft assy level during inspection.
Page 4742 of 5135

C81796F45254
(A)
C83851
C83155
C80293
− DRIVE SHAFT / PROPELLER SHAFTFRONT DRIVE SHAFT (2AZ−FSE)
30−15
AVENSIS Supplement (RM1045E)
HINT:
For dimension (A), refer to the following table.
Drive shaft typeDimension (A) mm (in.)
LH546.1(21.50) á5.0 (0.20)
RH884.0 (34.80) á5.0 (0.20)
41. INSTALL FRONT DRIVE SHAFT ASSY LH
(a) Coat the inboard joint shaft assy LH spline with gear oil.
(b) Align the shaft splines and install the drive shaft assy LH
with a brass bar and hammer.
NOTICE:
SSet the snap ring with the opening side facing down-
wards.
SBe careful not to damage the oil seal, boot and dust
cover.
42. INSTALL FRONT DRIVE SHAFT ASSY RH (RH DRIVE
SHAFT)
(a) Coat the inboard joint shaft assy RH spline with gear oil.
(b) Align the shaft splines and install the drive shaft assy RH
with the 2 bolts.
Torque: 64 Nm (650 kgfcm, 47 ftlbf)
NOTICE:
Do not damage the oil seal, boot and dust cover.
43. INSTALL FRONT AXLE ASSY LH
(a) Install the drive shaft assy LH to the front axle assy LH.
NOTICE:
SBe careful not to damage the outboard joint boot.
SBe careful not to damage the speed sensor rotor.
44. INSTALL FRONT SUSPENSION ARM SUB−ASSY
LOWER NO.1LH
(a) Install the lower ball joint to the front suspension arm sub−
assy lower No.1LH with the bolt and 2 nuts.
Torque: 89 Nm (908 kgfcm, 66 ftlbf)
Page 4743 of 5135

F44775
C80291
F13686
Hold
Turn
C68609
30−16
− DRIVE SHAFT / PROPELLER SHAFTFRONT DRIVE SHAFT (2AZ−FSE)
AVENSIS Supplement (RM1045E)
45. INSTALL TIE ROD END SUB−ASSY LH
(a) Install the tie rod end sub−assy LH to the steering knuckle with the nut.
Torque: 49 Nm (500 kgfcm, 36 ftlbf)
(b) Install a new cotter pin.
NOTICE:
If the holes for the cotter pin are not aligned, tighten the nut up to 60_further.
46. CONNECT SPEED SENSOR FRONT LH
(a) Install the speed sensor front LH to the steering knuckle
with the bolt.
Torque: 8.0 Nm (82 kgfcm, 71in.lbf)
(b) Connect the speed sensor wire and flexible hose to the
shock absorber with the bolt.
Torque:19Nm(194 kgfcm,14ftlbf)
NOTICE:
SBe careful not to damage the speed sensor.
SKeep the speed sensor clean.
SDo not twist the sensor wire when installing the sen-
sor.
47. INSTALL FRONT STABILIZER LINK ASSY LH
(a) Install the front stabilizer link assy LH with the nut.
Torque: 74 Nm (755 kgfcm, 55 ftlbf)
HINT:
If the ball joint turns together with the nut, use a hexagon
wrench (6 mm) to hold the stud.
48. INSTALL FRONT AXLE HUB LH NUT
(a) Install a new axle hub LH nut.
Torque: 216Nm (2,200 kgfcm,159 ftlbf)
(b) Using a chisel and hammer, stake the axle hub LH nut.
Page 4744 of 5135
− DRIVE SHAFT / PROPELLER SHAFTFRONT DRIVE SHAFT (2AZ−FSE)
30−17
AVENSIS Supplement (RM1045E)
49. INSTALL ENGINE UNDER COVER LH
50. INSTALL FRONT WHEEL
Torque:103 Nm(1,050 kgfcm, 76 ftlbf)
51. ADD AUTOMATIC TRANSAXLE FLUID (A/T TRANSAXLE)
(SEE PUB. NO. RM1018E ON PAGE 40−2)
52. INSPECT AND ADJUST AUTOMATIC TRANSAXLE FLUID (A/T TRANSAXLE)
(SEE PUB. NO. RM1018E ON PAGE 40−2)
53. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT (SEE PUB. NO. RM1018E ON PAGE 26−6)
54. CHECK ABS SPEED SENSOR SIGNAL
(a) ABD WITH EBD & BA & TRAC & VSC SYSTEM (SEE PUB. NO. RM1018E ON PAGE 5−756)