Page 3417 of 5135

B66528
Clip
B65292
700 mm120 mm
Adhesive Tape
Adhesive Tape
Protective Cover
A79919
Claw
Claw
76±48
± EXTERIOR/INTERIOR TRIMROOF HEADLINING ASSY (LIFTBACK MODELS)
AVENSIS REPAIR MANUAL (RM1018E)
25. REMOVE FRONT PILLAR GARNISH RH
(a) Using a screwdriver, disengage the 2 clips and remove
the pillar garnish.
HINT:
Tape the screwdriver tip before use.
(b) Pull the garnish upward and remove if from the instrument
panel.
(c) w/ Curtain shield airbag:
Protect the curtain shield airbag LH.
(1) Thoroughly cover the airbag with cloth or nylon of
700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the
ends of the cover in place with adhesive tape as
shown in the illustration.
NOTICE:
Cover the curtain shield airbag with a protective cover as
soon as the front pillar garnish is removed.
26. REMOVE FRONT PILLAR GARNISH LH
HINT:
Use the same procedures described for the RH side.
27. REMOVE RH VISOR ASSY
(a) Remove the 2 screws and visor.
28. REMOVE LH VISOR ASSY
(a) Remove the 2 screws and visor.
29. REMOVE MAP LAMP ASSY
(a) Using a screwdriver, disengage the 6 claws and remove
the lens cover.
HINT:
Tape the screwdriver tip before use.
(b) Remove the 2 screws.
(c) Using a moulding remover, disengage the claws.
(d) Disconnect the map lamp switch connector and sliding
roof switch connector, and remove the map lamp.
Page 3418 of 5135
B66541Claw
Claw
B66529
ClawClaw
B50596
90
± EXTERIOR/INTERIOR TRIMROOF HEADLINING ASSY (LIFTBACK MODELS)
76±49
AVENSIS REPAIR MANUAL (RM1018E)
30. REMOVE ROOM LAMP ASSY NO.2
(a) Using a moulding remover, disengage the 8 claws and re-
move the lens cover.
HINT:
Tape the screwdriver tip before use.
(b) Using a moulding remover, disengage the claws.
(c) Disconnect the map lamp switch connector and remove
the map lamp.
31. REMOVE ASSIST GRIP SUB±ASSY
(a) Using a screwdriver, disengage the 2 claws and remove
the 2 assist grip covers.
HINT:
Tape the screwdriver tip before use.
(b) Remove the 2 bolts and assist grip.
32. REMOVE VISOR HOLDER
(a) Remove the holder of the sun visor by turning it counter-
clockwise.
33. REMOVE SUN ROOF OPENING TRIM MOULDING (W/ SLIDING ROOF)
Page 3419 of 5135
B66557
Clip
w/ Sliding Roof
w/o Sliding Roof
B66554
Tape
w/ Sliding Roof
w/o Sliding Roof
Tape
76±50
±
EXTERIOR/INTERIOR TRIM ROOF HEADLINING ASSY(LIFTBACK MODELS)
AVENSIS REPAIR MANUAL (RM1018E)
34.REMOVE ROOF HEADLINING ASSY
(a)Using a clip remover, disengage the 2 clips and remove the roof headling.
35.INSTALL ROOF HEADLINING ASSY
(a)Align the markings, and then install the wire harness with tape.
NOTICE:
Attach the roof wire harness securely.
(b)Install the 2 clips.
36.INSTALL REAR SEAT ASSY (See page 72±21)
Page 3420 of 5135
760WV±01
B70682
Roof Side Garnish Inner RH
Front Pillar Garnish RH
Front Door Opening Trim Weatherstrip RH
Center Pillar Garnish RHRear Door Opening Trim Weatherstrip RH
Front Door
Scuff Plate RH
Rear Door Scuff
Plate RH
Cowl Side Trim Board RH
41.2 (420, 30)Center Pillar Garnish
Lower RH
Front Pillar Garnish LH
Front Door Opening Trim
Weatherstrip LH
Cowl Side Trim Board LH
Front Door Scuff Plate LH
Center Pillar Garnish Lower LH
Rear Door Scuff Plate LH
Center Pillar Garnish LH
Rear Door Opening Trim
Weatherstrip LH
Roof Side Garnish Inner LH
Package Tray
Trim Panel Assy
Nm (kgfcm ftlbf): Specified torque
41.2 (420, 30)
Rear Floor Finish Plate
Deck Trim Side
Panel Assy RH
Deck Trim Side
Board LH
Rear Headlining Sub±assy 76±42
± EXTERIOR/INTERIOR TRIMROOF HEADLINING ASSY (LIFTBACK MODELS)
AVENSIS REPAIR MANUAL (RM1018E)
ROOF HEADLINING ASSY (LIFTBACK MODELS)
COMPONENTS
Page 3421 of 5135
B70683
LH Visor Assy Visor Holder w/ Sliding Roof
Roof Headlining Assy
RH Visor Assy
Map Lamp AssyRoom Lamp Assy No. 2
Lens Cover
Assist Grip
Sub±assy
Lens CoverAssist Grip Sub±assy
Assist Grip Sub±assy
Assist Grip Sub±assy
Sun Roof Opening
Trim Moulding
± EXTERIOR/INTERIOR TRIMROOF HEADLINING ASSY (LIFTBACK MODELS)
76±43
AVENSIS REPAIR MANUAL (RM1018E)
Page 3422 of 5135
B66566
w/o Sliding Roof
LH Visor Assy Visor HolderRoof Headlining Assy
RH Visor Assy
Map Lamp AssyRoom Lamp Assy No. 2
Lens Cover
Assist Grip Sub±assy
Lens CoverAssist Grip Sub±assy
Assist Grip Sub±assy
Assist Grip Sub±assy
76±44
± EXTERIOR/INTERIOR TRIMROOF HEADLINING ASSY (LIFTBACK MODELS)
AVENSIS REPAIR MANUAL (RM1018E)
Page 3423 of 5135

760WU±01
B66532
Clip
Claw
B66531
Clip
Claw
B66533
Clip
Claw
76±36
± EXTERIOR/INTERIOR TRIMROOF HEADLINING ASSY (SEDAN MODELS)
AVENSIS REPAIR MANUAL (RM1018E)
REPLACEMENT
HINT:
The installation is in the reverse order of the removal. However, when there is a special point concerning
the installation, it is indicated.
1. REMOVE FRONT DOOR SCUFF PLATE RH
(a) Using a screwdriver, disengage the 5 clips and 2 claws,
and remove the scuff plate.
HINT:
Tape the screwdriver tip before use.
2. REMOVE FRONT DOOR SCUFF PLATE LH
HINT:
Use the same procedures described for the RH side.
3. REMOVE REAR DOOR SCUFF PLATE RH
(a) Using a screwdriver, disengage the 3 clips and 2 claws,
and remove the scuff plate.
HINT:
Tape the screwdriver tip before use.
4. REMOVE REAR DOOR SCUFF PLATE LH
HINT:
Use the same procedures described for the RH side.
5. REMOVE COWL SIDE TRIM BOARD RH
(a) Using a screwdriver, disengage the clip and 2 claw and re-
move the trim board.
HINT:
Tape the screwdriver tip before use.
6. REMOVE COWL SIDE TRIM BOARD LH
HINT:
Use the same procedures described for the RH side.
Page 3424 of 5135

B66534
B66535
Clip
B66527
Clip
±
EXTERIOR/INTERIO R TRI M ROOF HEADLINING ASS Y(SEDAN MODELS)
76±37
A VENSIS RE PAIR MANUAL (RM1018E)
7. REMOV E FRONT DOOR OPENING TRIM WE ATHERSTRIP RH
8 . REMOVE FRONT DOOR OPENING TRIM WE ATHERSTRIP LH
9 . REMOVE REAR DOOR OPENING TRIM WE ATHERSTRIP RH
10 . REMOVE REAR DOOR OPENING TRIM WE ATHERSTRIP LH
1 1 . REMOVE CENTER PILLAR GARNISH LOWER RH
(a ) Remove the floor anchor cove r.
(b ) Remove the bolt and outer belt on the floor anchor side.
(c ) Usin g a screwdrive r, disengage the 2 clips and remove
th e pillar garnish lowe r.
HIN T:
T ape the screwdriver tip before use.
12 . REMOVE CENTER PILLAR GARNISH LOWER LH
HIN T:
Use the same procedures described for the RH side.
13. REMOVE CENTER PILLAR GARNISH UPPER RH
(a ) Usin g a screwdrive r, disengage the clip and 2 screws and
remov e the pillar garnish.
HIN T:
T ape the screwdriver tip before use.
14 . REMOVE CENTER PILLAR GARNISH UPPER LH
HIN T:
Use the same procedures described for the RH side.
15 . REMOVE REAR SE AT ASSY ( See page 72±27 , 72±32 )