Page 3377 of 5135
B66547B66547
LH Visor Assy Visor HolderRoof Headlining Assy
RH Visor Assy
Map Lamp Assy
Room Lamp Assy No. 2Lens Cover
Assist Grip Sub±assy
Lens Cover
Assist Grip Sub±assy
Assist Grip Sub±assy
Assist Grip Sub±assy
Wagon Models
± SLIDING ROOF/CONVERTIBLESLIDING ROOF
74±13
AVENSIS REPAIR MANUAL (RM1018E)
Page 3378 of 5135
B67837
Sliding Roof Glass Assy
Sliding Roof Weatherstrip Assy
Bracket
BracketBracket Sliding Roof Drive
Gear Sub±assy
Sliding Roof Housing
Sub±assy
Drain Hose
Drain Hose
Drain Hose Drain Hose
74±14
± SLIDING ROOF/CONVERTIBLESLIDING ROOF
AVENSIS REPAIR MANUAL (RM1018E)
Page 3379 of 5135

7408W±01
± SLIDING ROOF/CONVERTIBLESLIDING ROOF SYSTEM
74±7
AVENSIS REPAIR MANUAL (RM1018E)
RESET
1. RESET SLIDING ROOF MOTOR
(a) If the AUTO operation function does not operate, reset the sliding roof motor as follows:
(1) Press the sliding roof switch on the TILT UP side and hold it until the sliding roof motor stops.
Then release the switch and leave it untouched for 10 seconds or more.
(2) Press the sliding roof switch on the TILT UP side again for 10 seconds or more and hold it until
the sliding roof glass stops at the fully open and up position.
(3) Release the switch, press it again within 5 seconds and hold it until a series of movements indi-
cated below have been completed:
Fully closing Fully opening Fully closing
HINT:
When the battery terminal is disconnected or after the jam protection function has operated, the sliding roof
motor ECU may not detect the position of the roof glass. If the AUTO operation function is still disabled even
after the sliding roof motor is reset, the Hall IC (built in the sliding roof motor) for detecting the roof glass
position may be malfunctioning.
Page 3380 of 5135

7408V±01
B67892
1
4 3
2
B67891
10
9876 54321
A05
115
74±6
±
SLIDING ROOF/CONVERTIBL ESLIDING ROOF SYSTEM
A VENSIS RE PAIR MANUAL (RM1018E)
INSPECTION
1. INSPEC T SLIDING ROOF MO TOR SWITCH ASSY
(a ) Remove the sliding roof motor switch
( See pages 76±36 , 76±45 and 76±54 ).
(b ) Check the resistance between the terminals when oper-
ating the switch.
Standard:
T erminal s No.Switch OperationSpecified Condition
1 ± 2TI LT UP is pressedBelow 1
2 ± 3SLIDE OPEN is pressedBelow 1
1, 3 ± 2OFF10 k or higher
If the result is not as specified, replace the switch ass y.
2 . INSPECT SLIDING ROOF MO TOR ASSY
(a ) Disconnect the sliding roof motor connector
( See pages 76±36 , 76±45 and 76±54 ).
(b) Check the resistance and voltage between the terminals of the wire harness side connector.
Standard:
Terminals No.ConditionSpecified Condition
5 Body groundConstantBelow 1
3 ± 5Ignition switch ON10 to 14 V
10 ± 5Constant10 to 14 V
6 ± 5TILT UP is pressedBelow 1
1 ± 5SLIDE OPEN is pressedBelow 1
8 ± 5Ignition switch OFF
ON, Engine idle speedPulse generation *
Reference (*): Using an oscilloscope
ItemContents
Tool Setting10 V/DIV., 20 ms/DV.
Vehicle ConditionEngine idle speed
If the result is not as specified, there may be a malfunction on
the wire harness side.
Page 3381 of 5135

760X6±01
B68949
B69147
76±14
±
EXTERIOR/INTERIOR TRIM FUEL LID LOCK CONTROL ASSY
AVENSIS REPAIR MANUAL (RM1018E)
REPLACEMENT
HINT:
The installation is in the reverse order of the removal. However, when there is a special point concerning
the installation, it is indicated.
1.REMOVE LUGGAGE COMPARTMENT TRIM COVER INNER LH (SEDAN MODELS) (See page 76±36)
(a) Remove the luggage compartment floor carpet.
(b) Remove the 2 rope hooks.
(c) Remove the rear floor finish plate.
(d) Remove the 2 luggage compartment trim hooks.
(e) Remove the luggage compartment trim inner.
2.REMOVE DECK TRIM SIDE BOARD LH (LIFTBACK MODELS) (See page 76±45)
(a) Remove the 2 rope hooks.
(b) Remove the rear floor finish plate.
(c) Remove the rear door opening trim weatherstrip LH.
(d) Remove the rear door scuff plate LH.
(e) Remove the deck trim side board.
3.REMOVE DECK TRIM SIDE PANEL ASSY LH (WAGON MODELS) (See page 76±54)
(a) Remove the rear door opening trim weatherstrip LH
(b) Remove the rear door scuff plate.
(c) Remove the tonneau cover.
(d) Remove the deck board.
(e) Remove the deck floor box rear.
(f) Remove the deck floor box LH.
(g) Remove the deck floor box front.
(h) Remove the rear floor finish plate.
(i) Remove the luggage compartment trim hook No. 2.
(j) Remove the deck trim side board.
4. REMOVE FUEL LID LOCK CONTROL ASSY
(a) Disconnect the connector.
(b) Remove the nut and fuel lid lock control.
5. REMOVE FUEL FILLER OPENING LID LOCKRETAINER
(a) Remove the fuel filler opening lid lock retainer, as shown
in the illustration.
Page 3382 of 5135
B68950
A
Check Hole
B68951
Male Part
Female Part
± EXTERIOR/INTERIOR TRIMFUEL LID LOCK CONTROL ASSY
76±15
AVENSIS REPAIR MANUAL (RM1018E)
6. INSTALL FUEL LID LOCK CONTROL ASSY
(a) Install the fuel lid lock control with the the nut.
Torque: 8.0 Nm (82 kgfcm, 71 in.lbf)
HINT:
Check to see that the tip of the lock is securely insearted into
hole A, looking inside through the check hole.
7. INSTALL FUEL FILLER OPENING LID LOCK
RETAINER
(a) Install the fuel filler opening lid lock retainer as shown in
the illustration.
Page 3383 of 5135
B69320
Sedan Models
Liftback Models
Wagon ModelsSlit
Slit
Strap
Strap
Strap
Slit 76±16
± EXTERIOR/INTERIOR TRIMFUEL LID LOCK CONTROL ASSY
AVENSIS REPAIR MANUAL (RM1018E)
(b) Pass the strap through the slit on the trim as shown in the
illustration.
(c) Attach a strap to the trim.
Page 3384 of 5135
760X5±01
B68948
Sedan Models
Luggage Compartment Trim Hook No. 2
Rope Hook Assy Luggage Compartment Floor Carpet
Luggage Compartment Trim Inner LH
5.0 (51, 44 in.´lbf)
: Specified torqueN´m (kgf´cm, ft´lbf)
Rear Floor Finish Plate
Fuel Lid Lock Control Assy
Fuel Filler Opening Lid Lock Retainer
5.5 (56, 49 in.´lbf)
± EXTERIOR/INTERIOR TRIMFUEL LID LOCK CONTROL ASSY
76±11
AVENSIS REPAIR MANUAL (RM1018E)
FUEL LID LOCK CONTROL ASSY
COMPONENTS