Page 1969 of 4133

AR82.10-P-5103GI
Remove/install fog lamp
27.2.01
MODELS
163.113 /154 #A as of 289565,
163.113 /154 #X as of 754620,
163.128 /157 /175
P82.10-2778-06
1
Lever
2
Fog lamp
3
Electrical connector
4
Grommets
Remove/install
1
Press lever (1) to release the fog lamp (2)
Pulling hook
*140589023300
2
Disconnect fog lamp (2) from front bumper
Exercise caution when pulling at the
edges of the fog lamp.
Installation:
First notch in the fog lamp at
the edges. Ensure that the lever (1) securely
holds the fog lamp in place.
Pulling hook
*140589023300
3
Disconnect electrical connector (3) from fog
lamp
4
Pull off grommets (4)
Installation:
Ensure that the grommets
are installed loosely and without kinks.
5
Install in the reverse order
6
Check fog lamp adjustment and adjust if
necessary
e
Check and correct headlamp adjustment
AP82.10-P-8260GH
Pulling hooks
140 589 02 33 00
Copyright DaimlerChrysler AG 20.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1
Page 1970 of 4133

AP82.10-P-8260GH
Check and correct headlamp adjustment
2.7.97
MODEL
163
a=Marking for low beams
b=Marking for high beams
c=Marking for fog lamps
P82.10-0212-02
Check
1
Drive vehicle to level surface
The vehicle level must not change when the
brakes are applied.
Vehicle must be in ready-for-the-road
condition (unladen weight, fuel tank full or
proper additional weight).
Correctly adjust tire pressure.
Load driver's seat with 75 kg or a person
(except USA)
2
Align headlamp adjustment tester to vehicle
and adjust height according to marking in lens
Follow the operating instructions for
headlamp beam setting equipment exactly
*WH58.30-Z-1002-09A
Danger!
Risk of accident
from vehicle starting off by
itself when engine running.
Risk of injury
suffered in the form of bruises or burns to the
hands when reaching in while the engine
cranks or runs
Secure vehicle to prevent it from moving off
by itself.
Wear closed and close-fitting work clothes.
Do not touch hot or rotating parts.
AS00.00-Z-0005-01A
3
Run engine and switch on low beam
4
Check headlamp range control for proper
function
(except USA)
The light beams from both headlamps should
change uniformly
5
Set headlamp range control switch to position 0
6
Check low beams
Adjust if necessary (except USA)
AP82.10-P-8260-01A
Due to the common reflector unit, the low
beams, high beams and fog lamps are
adjusted simultaneously.
US version:
#
See "Owner's Manual"
7
Check high beam adjustment
AP82.10-P-8260-02A
8
Check fog lamps
AP82.10-P-8260-04A
Commercially available tools
(see Workshop Equipment Manual)
Number
Designation
Make (e.g.)
Order number
Copyright DaimlerChrysler AG 20.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1
Page 1971 of 4133
WH58.30-Z-1002-09A
Headlamp adjuster
Robert Bosch GmbH
Franz Oechsle Str. 4
D-73207 Plochingen,
Germany
Copyright DaimlerChrysler AG 20.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 2
Page 1972 of 4133

AR88.20-P-2200GK
Remove/install rear bumper
26.2.01
MODEL
163.113 #A as of 289565,
163.113 #X as of 754620,
163.154 #A as of 289565,
163.128 /157 /175
P88.20-2200-09
Remove/Install
1.1
Disconnect antenna connector of E-call
emergency call system
Only with emergency call system E-Call,
code 349.
The connector is located behind side flap on
right C-pillar paneling at vehicle jacking point.
2
Remove panelings (1)
Do not damage paint. Do not break off
clips.
Installation wedge
*115589035900
3
Remove screws (2)
*BA88.20-P-1008-01B
4.1
Remove nut for dirt trap retaining strap from
vehicle underbody
Only if present
*BA88.30-P-1004-01A
5
Pull bumper toward rear and remove
Do not damage paint/wiring harness.
Pull directly over clips (arrows) and
detach from bracket.
Installation:
Align bumper at tailgate and
at taillamps
6.1
Remove rubber seal for E-call emergency call
system antenna from body at right
Only with emergency call system E-Call,
code 349.
7.1
Detach connector from Parktronic system
Only with Parktronic system (PTS), code
220a.
Remove left rubber seal from body.
8
Install in the reverse order
Bumper
Number
Designation
Model 163
BA88.20-P-1008-01B
Screw for rear bumper on mount
Nm
8
Copyright DaimlerChrysler AG 20.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1
Page 1973 of 4133
Detachable body components, underride guard
Number
Designation
Model 163
as of
1.9.01
BA88.30-P-1004-01A
Nut for retaining strap on mud guard on vehicle
underbody
Nm
6
Long wedge
115 589 03 59 00
Copyright DaimlerChrysler AG 20.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 2
Page 1974 of 4133
GF82.15-P-2100GH
Telescopic nozzle for headlamp cleaning system, location/task/design/function
26.3.01
MODEL
163 as of 01.09.01 with CODE (600a) headlamp cleaning system
P82.15-2084-06
1
Telescopic nozzles
Telescopic nozzle for headlamp cleaning
system, location
The two telescopic nozzles are both arranged
in the front bumper, under the headlamps.
Telescopic nozzle for headlamp cleaning
system, design
The telescopic nozzle is a hydraulically
extendable telescoping section with
integrated return springs and has no electrical
connection.
Telescopic nozzle for headlamp cleaning
system, task
Cleaning of headlamp glass
Function of headlamp cleaning system
telescopic nozzles
GF82.15-P-2100-04GH
Copyright DaimlerChrysler AG 17.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1
Page 1975 of 4133
GF82.15-P-0002-03GH
Headlamp cleaning system (HCS), location of
components
n
P82.15-2083-06
F2k5
Relay 5
M5/2
HCS pump
N10/1
Extended activity module (EAM)
S4/1
HCS [SRA] switch
Copyright DaimlerChrysler AG 17.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1
Page 1976 of 4133
GF82.15-P-9998GHZ
Survey of system components for headlamp cleaning system (HCS),
location/task/design/function
30.3.01
MODEL
163 as of 01.9.01 with CODE (600a) headlamp cleaning system
Headlamp cleaning system (HCS), location of
components
GF82.15-P-0002-03GH
Telescopic nozzle for headlamp cleaning
system, location/task/design/function
GF82.15-P-2100GH
Table of contents, function description for
headlamp cleaning system (HCS)
GF82.15-P-0998GHZ
Copyright DaimlerChrysler AG 17.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1