Page 2057 of 3502
SQUEAK AND RATTLE TROUBLE DIAGNOSES
EI-9
C
D
E
F
G
H
J
K
L
MA
B
EI
Diagnostic WorksheetBIS0011C
PIIB0723E
Page 2058 of 3502
EI-10
SQUEAK AND RATTLE TROUBLE DIAGNOSES
SBT844
Page 2059 of 3502
CLIP AND FASTENER
EI-11
C
D
E
F
G
H
J
K
L
MA
B
EI
CLIP AND FASTENERPFP:76906
Clip and FastenerBIS0011D
SIIA0315E
Page 2060 of 3502
EI-12
CLIP AND FASTENER
SIIA0316E
Page 2061 of 3502
CLIP AND FASTENER
EI-13
C
D
E
F
G
H
J
K
L
MA
B
EI
SIIA0317E
Page 2062 of 3502
EI-14
FRONT BUMPER
FRONT BUMPERPFP:F2022
Removal and InstallationBIS0011E
CAUTION:
Bumper fascia is made of resin. Do not apply strong force to it, and be careful to prevent contact with
oil.
PIIB8681E
Page 2063 of 3502

FRONT BUMPER
EI-15
C
D
E
F
G
H
J
K
L
MA
B
EI
REMOVAL
1. Fully open hood assembly.
2. Remove front side of fender protector (LH/RH). Refer to EI-23, "
FENDER PROTECTOR" .
3. Disconnect the headlamp cleaner tube joint (1) of washer tank
(2). (With headlamp cleaner)
4. Remove clips of bumper fascia lower side.
5. Remove screws of bumper fascia left/right side.
6. Remove clips of bumper fascia upper side, and then pull out bumper fascia toward front of vehicle while
extending bumper fascia side surface toward vehicle outside.
7. Disconnect fog lamp harness connectors (LH/RH) after pulling out, and then remove bumper fascia.
CAUTION:
When removing bumper fascia, 2 workers are required so as to prevent it from dropping.
8. Remove fog lamp assembly (LH/RH). Refer to LT- 1 2 6 , "
FRONT FOG LAMP" .
9. Remove bumper energy absorber.
10. Remove bumper reinforcement mounting nuts and bumper reinforcement.
11. Unscrew bumper stay mounting bolts, and remove bumper stay (LH/RH).
12. Unscrew bumper side bracket mounting screws, and remove bumper side bracket (LH/RH).
INSTALLATION
Install in the reverse order of removal.
NOTE:
1. Bumper stay (RH) 2. Bolt 3. Bumper reinforcement
4. Nut 5. Bumper side bracket (RH) 6. Screw
7. Screw 8. Bumper molding (RH) 9. Clip (C205)
10. Fog lamp (RH) 11. Fog lamp (LH) 12. Bumper molding (LH)
13. Bumper fascia 14. Bumper energy absorber 15. Bumper side bracket (LH)
16. Bumper stay (LH) 17. License plate bracket 18. Bumper bracket
19. Rivet Pawl
PIIB8682E
Portion Clearance
Front bumper – Front grille A – A 4.0 – 8.0 mm (0.157 – 0.315 in)
Front bumper – Hood B – B 4.0 – 8.0 mm (0.157 – 0.315 in)
Front bumper – Headlamp C – C 0.8 – 3.2 mm (0.031 – 0.126 in)
Front bumper – Front fender D – D 0.0 – 0.7 mm (0.000 – 0.028 in)
Page 2064 of 3502
EI-16
FRONT BUMPER
REMOVAL AND INSTALLATION OF FRONT BUMPER MOLDING
Removal
1. Remove front bumper fascia.
2. Disengage the joint between front bumper fascia and front
bumper molding, and then remove front bumper molding.
Installation
Install in the reverse order of removal.
PIIB8288J