2003 NISSAN TEANA Service Manual

open bonnet window roof washer fluid battery low beam

Page 2161 of 3502

NISSAN TEANA 2003 Service Manual TIMING CHAIN
EM-53
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM

TIMING CHAINPFP:13028
Removal and InstallationBBS00597
1. O-ring 2. O-ring 3. Camshaft sprocket (INT)
4. Camshaft sprocket (EXH) 5. Chain tensioner

Page 2162 of 3502

NISSAN TEANA 2003 Service Manual EM-54
[QR]
TIMING CHAIN

REMOVAL
1. Remove the following parts.
RH front road wheel and tire
Undercover and splash guard (RH)
PCV hose; Refer to EM-19, "INTAKE MANIFOLD" .
Ignition coil; Refer

EM-54
[QR]
TIMING CHAIN

REMOVAL
1. Remove the following parts.
RH front road wheel and tire
Undercover and splash guard (RH)
PCV hose; Refer to EM-19, "INTAKE MANIFOLD" .
Ignition coil; Refer to EM-31, "IGNITION COIL" .
Rocker cover; Refer to EM-39, "ROCKER COVER" .
Reservoir tank of radiator; Refer to CO-13, "RADIATOR" .
Drive belt; Refer to EM-14, "DRIVE BELTS" .
Alternator; Refer to SC-27, "CHARGING SYSTEM" .
Drive belt auto-tensioner; Refer to EM-15, "Removal and Installation of Drive Belt Auto-Tensioner" .
Exhaust front tube; Refer to EX-2, "EXHAUST SYSTEM" .
2. Drain engine oil. Refer to LU-9, "
Changing Engine Oil" .
CAUTION:
Perform this step when engine is cold.
3. Remove A/C compressor with piping connected. Temporarily secure A/C compressor to vehicle side with
a rope to avoid putting a load on them. Refer to ATC-134, "
Removal and Installation of Compressor" .
4. Remove power steering oil pump with piping connected, and secure it to vehicle side temporarily. Refer to
PS-39, "
HYDRAULIC LINE" .
5. Securely support bottom of transaxle with suitable transmission jack.
6. Remove RH engine mounting insulator. Refer to EM-77, "
ENGINE ASSEMBLY" .
7. Remove oil pans (upper and lower), and oil strainer. Refer to EM-26, "
OIL PAN AND OIL STRAINER" .
8. To support engine, temporarily tighten removed front and rear engine mounting through-bolts for removing
oil pans (upper and lower). Refer to EM-77, "
ENGINE ASSEMBLY" .
9. Remove intake valve timing control cover with the following procedure:
a. Disconnect intake valve timing control solenoid valve harness connector.
b. Disconnect ground cables and remove harness clip.
c. Remove intake valve timing control solenoid valve, if necessary.
d. Loosen bolts in reverse order as shown in the figure.
e . U s e s e a l c u t t e r [ S S T: K V 1 0 1111 0 0 ] o r e q u i v a l e n t t o o l t o c u t l i q -
uid gasket for removal.
CAUTION:
Be careful not to damage the mating surfaces.
10. Pull chain guide between camshaft sprockets out through front cover.
11. Set No. 1 cylinder at TDC on its compression stroke with the following procedure:
a. Rotate crankshaft pulley clockwise and align TDC mark to timing
indicator on front cover.
KBIA0085E
KBIA0190E

Page 2163 of 3502

NISSAN TEANA 2003 Service Manual TIMING CHAIN
EM-55
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM

b. At the same time, make sure that the mating marks on camshaft
sprockets are located as shown in the figure.
If not, rotate crankshaft pulley one

Page 2164 of 3502

NISSAN TEANA 2003 Service Manual EM-56
[QR]
TIMING CHAIN

a. Loosen mounting bolts in reverse order as shown in the figure,
and remove RH engine mounting bracket.
b . U s e s e a l c u t t e r [ S S T: K V 1 0 1111 0 0 ] o r e

Page 2165 of 3502

NISSAN TEANA 2003 Service Manual TIMING CHAIN
EM-57
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM

19. Remove balancer unit timing chain and crankshaft sprocket.
20. Loosen mounting bolts in reverse order as shown in the figure,
and remove balance

Page 2166 of 3502

NISSAN TEANA 2003 Service Manual EM-58
[QR]
TIMING CHAIN

INSTALLATION
NOTE:
The figure shows the relationship between the mating mark on each
timing chain and that on the corresponding sprocket, with the com-
ponents installed.
1.

Page 2167 of 3502

NISSAN TEANA 2003 Service Manual TIMING CHAIN
EM-59
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM

3. Install crankshaft sprocket and balancer unit timing chain.
Make sure that crankshaft sprocket is positioned with mating
marks on cylinder block

Page 2168 of 3502

NISSAN TEANA 2003 Service Manual EM-60
[QR]
TIMING CHAIN

b. Apply a continuous bead of liquid gasket with tube presser [SST:
WS39930000] to front cover as shown in the figure.
Use Genuine Liquid Gasket or equivalent.
NOTE:
Applic

Load next 8 pages

Page: < prev 1-10 ... 2129-2136 2137-2144 2145-2152 2153-2160 2161-2168 2169-2176 2177-2184 2185-2192 2193-2200 ... 3504 next >

USB port wiper blades coolant warning lights oil level stop start