2003 NISSAN TEANA manual transmission

MODEL J31 SERIES
2006 NISSAN EUROPE S.A.S.
All rights reserved. No part of this Electronic Service Manual may be reproduced or stored in a retrieval system, or transmitted in any
form, or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of Nissan
Europe S.A.S., Paris, France.
A GENERAL INFORMATION
B ENGINE
C TRANSMISSION/TRANSAXLE
D DRIVELINE/AXLE
E SUSPENSION
F BRAKES
G STEERING H RESTRAINTS
I BODY
J AIR CONDITIONER
K ELECTRICAL
L MAINTENANCE
M INDEXGI General Information
EM Engine Mechanical
LU Engine Lubrication System
CO Engine Cooling System
EC Engine Control System
FL Fuel System
EX Exhaust System
ACC Accelerator Control System
AT Automatic Transmission
CVT CVT
FAX Front Axle
RAX Rear Axle
FSU Front Suspension
RSU Rear Suspension
WT Road Wheels & Tires
BR Brake System
PB Parking Brake System
BRC Brake Control System
PS Power Steering System
SB Seat Belts
SRS Supplemental Restraint System (SRS)
BL Body, Lock & Security System
GW Glasses, Window System & Mirrors
RF Roof
EI Exterior & Interior
IP Instrument Panel
SE Seat
ATC Automatic Air Conditioner
SC Starting & Charging System
LT Lighting System
DI Driver Information System
WW Wiper, Washer & Horn
BCS Body Control System
LAN LAN System
AV Audio, Visual & Telephone System
ACS Auto Cruise Control System
PG Power Supply, Ground & Circuit Elements
MA Maintenance
IDX Alphabetical Index
QUICK REFERENCE INDEX
A
B
C
D
E
F
G
H
I
J
K
L
M

AT-3
D
E
F
G
H
I
J
K
L
MA
B
AT
CONSULT-II Reference Value .............................. 167
Diagnostic Procedure ........................................... 167
TROUBLE DIAGNOSIS FOR SYMPTOMS ............ 168
Wiring Diagram — AT — NONDTC ...................... 168
A/T CHECK Indicator Lamp Does Not Come On . 173
Engine Cannot Be Started in “P” and “N” Position . 175
In “P” Position, Vehicle Moves Forward or Backward
When Pushed ....................................................... 176
In “N” Position, Vehicle Moves ............................. 176
Large Shock. “N” → “R” Position .......................... 177
Vehicle Does Not Creep Backward in “R” Position . 179
Vehicle Does Not Creep Forward in “D”, “3”, “2” or
“1” Position ........................................................... 181
Vehicle Cannot Be Started From D
1 ..................... 182
A/T Does Not Shift: D
1 → D2 or Does Not Kickdown:
D
4 → D2 ............................................................... 184
A/T Does Not Shift: D
2 → D3 ............................... 186
A/T Does Not Shift: D
3 → D4 ............................... 188
A/T Does Not Perform Lock-up ............................ 191
A/T Does Not Hold Lock-up Condition ................. 193
Lock-up Is Not Released ...................................... 195
Engine Speed Does Not Return To Idle (Light Brak-
ing D
4 → D3 ) ....................................................... 195
A/T Does Not Shift: D
4 → 33 , When A/T Selector
Lever “D” → “3” .................................................... 197
A/T Does Not Shift: 3
3 → 22 , When Selector Lever
“3” → “2” Position ................................................. 198
A/T Does Not Shift: 2
2 → 11 , When Selector Lever
“2” → “1” Position ................................................. 200
Vehicle Does Not Decelerate By Engine Brake (D
4
→ 3
3 ) ................................................................... 203
Vehicle Does Not Decelerate By Engine Brake (3
3
→ 2
2 ) ................................................................... 205
Vehicle Does Not Decelerate By Engine Brake (2
2
→ 1
1 ) ................................................................... 208
TCM Self-diagnosis Does Not Activate ................ 210
TRANSMISSION CONTROL MODULE ..................211
Removal and Installation ....................................... 211
SHIFT CONTROL SYSTEM ................................... 213
Control Device Removal and Installation ............. 213
Adjustment of A/T Position ................................... 215
Checking of A/T Position ...................................... 215
A/T SHIFT LOCK SYSTEM .................................... 216
Description ........................................................... 216
Shift Lock System Electrical Parts Location ......... 216
Wiring Diagram — AT — SHIFT ........................... 217
Shift Lock Control Unit Reference Values ............ 221
Component Inspection ......................................... 222
ON-VEHICLE SERVICE ......................................... 225
Control Valve Assembly and Accumulators .......... 225
Park/Neutral Position (PNP) Switch ..................... 230
Differential Side Oil Seal Replacement ................ 231
Revolution Sensor Replacement .......................... 233
Turbine Revolution Sensor (Power Train Revolution
Sensor) Replacement .......................................... 234
AIR BREATHER HOSE .......................................... 236
Removal and Installation [Air Breather Hose (Oil
Catch Tank to Air Duct)] ....................................... 236
Removal and Installation [Oil Catch Tank and Air Breather Hose (A/T assembly to Oil catch tank)] . 239
TRANSAXLE ASSEMBLY ......................................241
Removal and Installation ......................................241
OVERHAUL ............................................................246
Components .........................................................246
Oil Channel ...........................................................252
Locations of Adjusting Shims, Needle Bearings and
Thrust Washers ....................................................253
Locations of Snap Rings .......................................254
DISASSEMBLY .......................................................255
Disassembly .........................................................255
REPAIR FOR COMPONENT PARTS .....................272
Manual Shaft ........................................................272
Oil Pump ...............................................................275
Control Valve Assembly ........................................280
Control Valve Upper Body ....................................289
Control Valve Lower Body ....................................293
Reverse Clutch .....................................................296
High Clutch ...........................................................301
Forward and Overrun Clutches ............................307
Low & Reverse Brake ...........................................315
Rear Internal Gear, Forward Clutch Hub and Over-
run Clutch Hub ......................................................319
Output Shaft, Idler Gear, Reduction Pinion Gear and
Bearing Retainer ...................................................323
Band Servo Piston Assembly ...............................329
Final Drive ............................................................335
ASSEMBLY .............................................................339
Assembly (1) .........................................................339
Adjustment (1) ......................................................340
Assembly (2) .........................................................345
Adjustment (2) ......................................................352
Assembly (3) .........................................................355
SERVICE DATA AND SPECIFICATIONS (SDS) ....362
General Specifications ..........................................362
Vehicle Speed Which Gear Shifting Occurs .........362
Vehicle Speed at When Lock-up Occurs/Releases .362
Stall Revolution .....................................................363
Line Pressure .......................................................363
Adjusting shims, Needle Bearings, Thrust Washers
and Snap Rings ....................................................363
Control Valves ......................................................364
Accumulator ..........................................................365
Clutch and Brakes ................................................366
Final Drive ............................................................367
Planetary Carrier and Oil Pump ............................367
Input Shaft ............................................................367
Reduction Pinion Gear .........................................367
Band Servo ...........................................................368
Output Shaft .........................................................368
Bearing Retainer ...................................................368
Total End Play .......................................................368
Reverse Clutch End Play ......................................368
Removal and Installation ......................................368
Shift Solenoid Valves ............................................368
Solenoid Valves ....................................................368
A/T Fluid Temperature Sensor ..............................368
Revolution Sensor ................................................369

INTELLIGENT KEY SYSTEM
BL-77
C
D
E
F
G
H
J
K
L
MA
B
BL

STEERING LOCK UNIT REGISTRATION
Steering Lock Unit ID Registration
CAUTION:

The method for registering a steering lock unit ID depends on the status of the steering lock unit
and Intelligent Key unit (new or old unit).

After registration is completed, press ignition knob with a portable unit in the vehicle so that it can
be rotated, and confirm that it cannot be rotated even when ignition switch is pressed without a
portable unit in the vehicle.
For future information, see the CONSULT-II Operation Manual NATS.
CAN Communication System DescriptionBIS000X0
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitBIS000X1
Refer to LAN-49, "CAN System Specification Chart" .

CVT-3
D
E
F
G
H
I
J
K
L
MA
B
CVT
On Board Diagnosis Logic ..................................... 97
Possible Cause ...................................................... 97
DTC Confirmation Procedure ................................. 97
WITH CONSULT-II .............................................. 97
Wiring Diagram — CVT — LPSV ........................... 98
Diagnostic Procedure ............................................. 99
Component Inspection ......................................... 101
PRESSURE CONTROL SOLENOID VALVE A
(LINE PRESSURE SOLENOID VALVE) ........... 101
DTC P0746 PRESSURE CONTROL SOLENOID A
PERFORMANCE (LINE PRESSURE SOLENOID
VALVE) .................................................................... 102
Description ........................................................... 102
CONSULT-II Reference Value .............................. 102
On Board Diagnosis Logic ................................... 102
Possible Cause .................................................... 102
DTC Confirmation Procedure ............................... 102
WITH CONSULT-II ............................................ 102
Diagnostic Procedure ........................................... 103
DTC P0776 PRESSURE CONTROL SOLENOID B
PERFORMANCE (SEC PRESSURE SOLENOID
VALVE) .................................................................... 105
Description ........................................................... 105
CONSULT-II Reference Value .............................. 105
On Board Diagnosis Logic ................................... 105
Possible Cause .................................................... 105
DTC Confirmation Procedure ............................... 105
WITH CONSULT-II ............................................ 105
Diagnostic Procedure ........................................... 106
DTC P0778 PRESSURE CONTROL SOLENOID B
ELECTRICAL (SEC PRESSURE SOLENOID
VALVE) .................................................................... 108
Description ........................................................... 108
CONSULT-II Reference Value .............................. 108
On Board Diagnosis Logic ................................... 108
Possible Cause .................................................... 108
DTC Confirmation Procedure ............................... 108
WITH CONSULT-II ............................................ 108
Wiring Diagram — CVT — SECPSV ................... 109
Diagnostic Procedure ............................................ 110
Component Inspection .......................................... 112
PRESSURE CONTROL SORENOID VALVE B
(SECONDARY PRESSURE SOLENOID VALVE)
.. 112
DTC P0826 MANUAL MODE SWITCH CIRCUIT ...113
Description ............................................................ 113
CONSULT-II Reference Value ............................... 113
On Board Diagnosis Logic .................................... 113
Possible Cause ..................................................... 113
DTC Confirmation Procedure ................................ 113
WITH CONSULT-II ............................................. 113
Wiring Diagram — CVT — MMSW ....................... 114
Diagnostic Procedure ............................................ 115
Component Inspection .......................................... 117
MANUAL MODE SWITCH ................................. 117
DTC P0840 TRANSMISSION FLUID PRESSURE
SENSOR A CIRCUIT (SEC PRESSURE SENSOR) ..118
Description ............................................................ 118
CONSULT-II Reference Value ............................... 118On Board Diagnosis Logic ....................................118
Possible Cause .....................................................118
DTC Confirmation Procedure ...............................118
WITH CONSULT-II ............................................118
Wiring Diagram — CVT — SECPS ......................119
Diagnostic Procedure ...........................................120
DTC P0841 PRESSURE SENSOR FUNCTION .....123
Description ............................................................123
CONSULT-II Reference Value ..............................123
On Board Diagnosis Logic ....................................123
Possible Cause .....................................................123
DTC Confirmation Procedure ...............................123
WITH CONSULT-II ............................................123
Diagnostic Procedure ...........................................124
DTC P0845 TRANSMISSION FLUID PRESSURE
SENSOR B CIRCUIT (PRI PRESSURE SENSOR) .126
Description ............................................................126
CONSULT-II Reference Value ..............................126
On Board Diagnosis Logic ....................................126
Possible Cause .....................................................126
DTC Confirmation Procedure ...............................126
WITH CONSULT-II ............................................126
Wiring Diagram — CVT — PRIPS ........................127
Diagnostic Procedure ...........................................128
DTC P0868 SECONDARY PRESSURE DOWN .....131
Description ............................................................131
CONSULT-II Reference Value ..............................131
On Board Diagnosis Logic ....................................131
Possible Cause .....................................................131
DTC Confirmation Procedure ...............................131
WITH CONSULT-II ............................................131
Diagnostic Procedure ...........................................132
DTC P1701 TRANSMISSION CONTROL MODULE
(POWER SUPPLY) ..................................................134
Description ............................................................134
On Board Diagnosis Logic ....................................134
Possible Cause .....................................................134
DTC Confirmation Procedure ...............................134
WITH CONSULT-II ............................................134
Wiring Diagram — CVT — POWER .....................135
Diagnostic Procedure ...........................................136
DTC P1705 THROTTLE POSITION SENSOR .......139
Description ............................................................139
CONSULT-II Reference Value ..............................139
On Board Diagnosis Logic ....................................139
Possible Cause .....................................................139
DTC Confirmation Procedure ...............................139
WITH CONSULT-II ............................................139
Diagnostic Procedure ...........................................140
DTC P1722 ESTM VEHICLE SPEED SIGNAL ......141
Description ............................................................141
CONSULT-II Reference Value ..............................141
On Board Diagnosis Logic ....................................141
Possible Cause .....................................................141
DTC Confirmation Procedure ...............................141
WITH CONSULT-II ............................................141
Diagnostic Procedure ...........................................142
DTC P1723 CVT SPEED SENSOR FUNCTION .....143
Description ............................................................143

CVT-4 On Board Diagnosis Logic ....................................143
Possible Cause .....................................................143
DTC Confirmation Procedure ...............................143
WITH CONSULT-II ............................................143
Diagnostic Procedure ...........................................144
DTC P1726 ELECTRIC THROTTLE CONTROL
SYSTEM ..................................................................145
Description ............................................................145
On Board Diagnosis Logic ....................................145
Possible Cause .....................................................145
DTC Confirmation Procedure ...............................145
WITH CONSULT-II ............................................145
Diagnostic Procedure ...........................................146
DTC P1740 LOCK-UP SELECT SOLENOID VALVE
CIRCUIT ..................................................................147
Description ............................................................147
CONSULT-II Reference Value ..............................147
On Board Diagnosis Logic ....................................147
Possible Cause .....................................................147
DTC Confirmation Procedure ...............................147
WITH CONSULT-II ............................................147
Wiring Diagram — CVT — L/USSV ......................148
Diagnostic Procedure ...........................................149
Component Inspection ..........................................151
LOCK-UP SELECT SOLENOID VALVE ............151
DTC P1745 LINE PRESSURE CONTROL .............152
Description ............................................................152
On Board Diagnosis Logic ....................................152
Possible Cause .....................................................152
DTC Confirmation Procedure ...............................152
WITH CONSULT-II ............................................152
Diagnostic Procedure ...........................................152
DTC P1777 STEP MOTOR - CIRCUIT ...................153
Description ............................................................153
CONSULT-II Reference Value ..............................153
On Board Diagnosis Logic ....................................153
Possible Cause .....................................................153
DTC Confirmation Procedure ...............................153
WITH CONSULT-II ............................................153
Wiring Diagram — CVT — STM ...........................154
Diagnostic Procedure ...........................................155
Component Inspection ..........................................156
STEP MOTOR ...................................................156
DTC P1778 STEP MOTOR - FUNCTION ...............157
Description ............................................................157
CONSULT-II Reference Value ..............................157
On Board Diagnosis Logic ....................................157
Possible Cause .....................................................157
DTC Confirmation Procedure ...............................157
WITH CONSULT-II ............................................157
Diagnostic Procedure ...........................................158
CVT INDICATOR CIRCUIT .....................................159
Description ............................................................159
CONSULT-II Reference Value ..............................159
Diagnostic Procedure ...........................................159
CVT INDICATOR SYMPTOM CHART ...............159
TROUBLE DIAGNOSIS FOR SYMPTOMS ............160Wiring Diagram — CVT — NONDTC ...................160
CVT Indicator Lamp Does Not Come On ..............164
SYMPTOM: ........................................................164
DIAGNOSTIC PROCEDURE .............................164
Engine Cannot Be Started in “P” or “N” Position ...165
SYMPTOM: ........................................................165
DIAGNOSTIC PROCEDURE .............................165
In “P” Position, Vehicle Moves Forward or Backward
When Pushed .......................................................166
SYMPTOM: ........................................................166
DIAGNOSTIC PROCEDURE .............................166
In “N” Position, Vehicle Moves ..............................166
SYMPTOM: ........................................................166
DIAGNOSTIC PROCEDURE .............................166
Large Shock “N” → “R” Position ...........................167
SYMPTOM: ........................................................167
DIAGNOSTIC PROCEDURE .............................167
Vehicle Does Not Creep Backward in “R” Position .168
SYMPTOM: ........................................................168
DIAGNOSTIC PROCEDURE .............................168
Vehicle Does Not Creep Forward in “D” Position ..169
SYMPTOM: ........................................................169
DIAGNOSTIC PROCEDURE .............................169
CVT Does Not Shift ...............................................170
SYMPTOM: ........................................................170
DIAGNOSTIC PROCEDURE .............................170
Cannot Be Changed to Manual Mode ...................171
SYMPTOM: ........................................................171
DIAGNOSTIC PROCEDURE .............................171
CVT Does Not Shift in Manual Mode ....................171
SYMPTOM: ........................................................171
DIAGNOSTIC PROCEDURE .............................171
Vehicle Does Not Decelerate by Engine Brake .....172
SYMPTOM: ........................................................172
DIAGNOSTIC PROCEDURE .............................172
TRANSMISSION CONTROL MODULE ..................174
Removal and Installation .......................................174
COMPONENTS .................................................174
REMOVAL ..........................................................174
INSTALLATION ..................................................175
SHIFT CONTROL SYSTEM ....................................176
Removal and Installation .......................................176
CONTROL DEVICE COMPONENTS ................176
CONTROL CABLE COMPONENTS ..................177
REMOVAL ..........................................................177
INSTALLATION ..................................................178
Adjustment of CVT Position ..................................178
Checking of CVT Position .....................................179
CVT SHIFT LOCK SYSTEM ...................................180
Description ............................................................180
Shift Lock System Electrical Parts Location ..........180
Wiring Diagram — CVT — SHIFT ........................181
Shift Lock Control Unit Reference Values .............183
SHIFT LOCK HARNESS CONNECTOR TERMI-
NALS LAYOUT ..................................................183
SHIFT LOCK CONTROL UNIT INSPECTION

CVT SYSTEM
CVT-19
D
E
F
G
H
I
J
K
L
MA
B
CVT

CAN CommunicationBCS001G3
SYSTEM DESCRIPTION
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only. For details, refer to LAN-49,
"CAN System Specification Chart" .
Input/Output Signal of TCMBCS001G4
*1: Input by CAN communications.
*2: If these input and output signals are different, the TCM triggers the fail-safe function. Control item Fluid
pressure
control Select
control Shift con-
trol Lock-up
control CAN com-
munication
control Fail-safe
function
(*2)
Input PNP switch XXXXXX
Accelerator pedal position signal
(*1)XXXXXX
Closed throttle position signal
(*1)XXXX
Engine speed signal
(*1)XX XXX
CVT fluid temperature sensor X X X X X
Manual mode signal
(*1)XXXXX
Stop lamp switch signal
(*1)XXXX
Primary speed sensor X X X X X
Secondary speed sensor X X X X X X
Primary pressure sensor X X
Secondary pressure sensor X X X
TCM power supply voltage signal X X X X X X
Out-
put Step motor X X
TCC solenoid valve X X X
Lock-up select solenoid valve X X X
Line pressure solenoid valve X X X X
Secondary pressure solenoid valve X X X

CVT SYSTEM
CVT-21
D
E
F
G
H
I
J
K
L
MA
B
CVT

NOTE:
The gear ratio is set for every position separately.
“D” POSITION
Shifting over all the ranges of gear ratios from the lowest to the high-
est.
“M” POSITION
When the selector lever is put in the manual shift gate side, the fixed
changing gear line is set. By moving the selector lever to + side or -
side, the manual mode switch is changed over, and shift change like
M/T becomes possible following the changing gear set line step by
step.
DOWNHILL ENGINE BRAKE CONTROL (AUTO ENGINE BRAKE CONTROL)
When downhill is detected with the accelerator pedal released, the engine brake will be strengthened up by
downshifting so as not to accelerate the vehicle more than necessary.
ACCELERATION CONTROL
According to vehicle speed and a change of accelerator pedal angle, driver's request for acceleration and driv-
ing scene are judged. This function assists improvement in acceleration feeling by making the engine speed
proportionate to the vehicle speed. And a shift map which can gain a larger driving force is available for com-
patibility of mileage with drivability.
Lock-up and Select ControlBCS001G7

The torque converter clutch piston in the torque converter is engaged to eliminate torque converter slip to
increase power transmission efficiency.

The torque converter clutch control valve operation is controlled by the torque converter clutch solenoid
valve, which is controlled by a signal from TCM. The torque converter clutch control valve engages or
releases the torque converter clutch piston.

When shifting between “N” (“P”) ⇔ “D” (“R”), torque converter clutch solenoid controls engagement power
of forward clutch and reverse brake.

The lock-up applied gear range was expanded by locking up the
torque converter at a lower vehicle speed than conventional
CVT models.
SCIA1953E
SCIA4582E
SCIA1958E

CVT-24
TROUBLE DIAGNOSIS

TROUBLE DIAGNOSISPFP:00004
DTC Inspection Priority ChartBCS001GE
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
NOTE:
If DTC “U1000 CAN COMM CIRCUIT” is displayed with other DTCs, first perform the trouble diagnosis
for “DTC U1000 CAN COMMUNICATION LINE”. Refer to CVT-53
.
Fail-safeBCS001GF
The TCM has an electrical fail-safe mode. This mode makes it possible to operate even if there is an error in a
main electronic control input/output signal circuit.
FAIL-SAFE FUNCTION
If any malfunction occurs in a sensor or solenoid, this function controls the CVT to make driving possible.
Output Speed Sensor (Secondary Speed Sensor)
The shift pattern is changed in accordance with throttle position when an unexpected signal is sent from the
output speed sensor (secondary speed sensor) to the TCM. The manual mode position and second position is
inhibited, and the transaxle is put in “D”.
Input Speed Sensor (Primary Speed Sensor)
The shift pattern is changed in accordance with throttle position and secondary speed (vehicle speed) when
an unexpected signal is sent from the input speed sensor (primary speed sensor) to the TCM. The manual
mode position and second position is inhibited, and the transaxle is put in “D”.
PNP Switch
If an unexpected signal is sent from the PNP switch to the TCM, the transaxle is put in “D”.
Manual Mode Switch
If an unexpected signal is sent from the manual mode switch to the TCM, the transaxle is put in “D”.
CVT Fluid Temperature Sensor
If an unexpected signal is sent from the CVT fluid temperature sensor to the TCM, the gear ratio in use before
receiving the unexpected signal is maintained or the gear ratio is controlled to keep engine speed under 5,000
rpm.
Transmission Fluid Pressure Sensor A (Secondary Pressure Sensor)

If an unexpected signal is sent from the transmission fluid pressure sensor A (secondary pressure sensor)
to the TCM, the secondary pressure feedback control is stopped and the offset value obtained before the
non-standard condition occurs is used to control line pressure.

If transmission fluid pressure sensor A (secondary pressure sensor) error signal is input to TCM, second-
ary pressure feedback control stops, but line pressure is controlled normally.
Pressure Control Solenoid A (Line Pressure Solenoid)
If an unexpected signal is sent from the solenoid to the TCM, the pressure control solenoid A (line pressure
solenoid) is turned OFF to achieve the maximum fluid pressure.
Pressure Control Solenoid B (Secondary Pressure Solenoid)
If an unexpected signal is sent from the solenoid to the TCM, the pressure control solenoid B (secondary pres-
sure solenoid) is turned OFF to achieve the maximum fluid pressure.
Torque Converter Clutch Solenoid
If an unexpected signal is sent from the solenoid to the TCM, the torque converter clutch solenoid is turned
OFF to cancel the lock-up.
Priority Detected items (DTC)
1 U1000 CAN communication line
2 Except above