2003 NISSAN TEANA Service Manual

keyless bolt pattern wheel alignment driver seat adjustment fuel fill door release four wheel drive

Page 3161 of 3502

NISSAN TEANA 2003 Service Manual WHEEL HUB
RAX-3
C
E
F
G
H
I
J
K
L
MA
B
RAX

WHEEL HUBPFP:43202
On-Vehicle Inspection BDS0007Y
Make sure that the mounting conditions (looseness, backlash) of each components and the component condi-

Page 3162 of 3502

NISSAN TEANA 2003 Service Manual RAX-4
WHEEL HUB

4. Put matching mark on disc rotor and wheel hub and bearing
assembly, then remove disc rotor.
5. Remove bolts, and then remove wheel hub and bearing assem-
bly from axle housing.
6.

RAX-4
WHEEL HUB

4. Put matching mark on disc rotor and wheel hub and bearing
assembly, then remove disc rotor.
5. Remove bolts, and then remove wheel hub and bearing assem-
bly from axle housing.
6. Remove hub cap from axle housing.
Axle Housing
1. Remove wheel hub and bearing assembly from axle housing. Refer to RAX-3, "Wheel Hub and Bearing
Assembly" .
2. Remove parking brake shoe and parking brake cable from back plate. Refer to PB-5, "
PARKING BRAKE
SHOE" , PB-3, "PARKING BRAKE CONTROL" .
3. Remove anchor block mounting nuts, then remove anchor block and back plate from axle housing.
4. Remove coil spring. Refer to RSU-15, "
REAR LOWER LINK & COIL SPRING" .
5. Remove axle housing side nuts and bolts on radius rod and front lower link. Refer to RSU-13, "
RADIUS
ROD" , RSU-14, "FRONT LOWER LINK" .
6. Remove cotter pin, and then loosen suspension arm mounting nut of axle housing.
7. Remove suspension arm from axle housing so as not to damage ball joint boot using the ball joint remover
(suitable tool), and then remove axle housing from vehicle.
CAUTION:
Temporarily tighten the nut to prevent damage to threads and to prevent ball joint remover (suit-
able tool) from suddenly coming off.
INSPECTION AFTER REMOVAL
Check the components for deformation, cracks and other damage. Replace if there are.
Ball Joint Inspection
Check suspension arm ball joint boot for breakage, axial play, and torque. Refer to RSU-11, "INSPECTION
AFTER REMOVAL" .
INSTALLATION
Wheel Hub and Bearing Assembly
Installation is the reverse order of the removal. For tightening torque, refer to RAX-3, "COMPONENT" .
NOTE:
Do not reuse non-reusable parts.
Assemble disc rotor and wheel hub and bearing assembly by
aligning each matching mark as shown in the figure when install-
ing disc rotor.
NOTE:
Refer to BR-33, "
REAR DISC BRAKE" for assembly when
removing disc rotor without matching mark.
Check wheel sensor harness for proper connection. Refer to
BRC-33, "
WHEEL SENSORS" .
Adjust neutral position of steering angle sensor after checking
the wheel alignment for the models with VDC. Refer to BRC-40,
"Adjustment of Steering Angle Sensor Neutral Position" .
SDIA2638E
SDIA2638E

Page 3163 of 3502

NISSAN TEANA 2003 Service Manual WHEEL HUB
RAX-5
C
E
F
G
H
I
J
K
L
MA
B
RAX

Axle Housing
Installation is the reverse order of the removal. For tightening torque, refer to RAX-3, "COMPONENT" .
NOTE:
Do not reuse non-reusable parts.

Page 3164 of 3502

NISSAN TEANA 2003 Service Manual RAX-6
SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
Wheel BearingBDS00080
Axial end play0.05 mm (0.002 in) or less

Page 3165 of 3502

NISSAN TEANA 2003 Service Manual RF-1
ROOF
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION RF
A
B
RF

ROOF
PRECAUTIONS .......................................................... 2
Precautions for Supplemental Restraint System
(SRS) �

RF-1
ROOF
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION RF
A
B
RF

ROOF
PRECAUTIONS .......................................................... 2
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 2
Precautions .............................................................. 2
PREPARATION ........................................................... 3
Commercial Service Tools ........................................ 3
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 4
Work Flow ................................................................ 4
CUSTOMER INTERVIEW ..................................... 4
DUPLICATE THE NOISE AND TEST DRIVE ....... 5
CHECK RELATED SERVICE BULLETINS ........... 5
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 5
REPAIR THE CAUSE ........................................... 5
CONFIRM THE REPAIR ....................................... 6
Generic Squeak and Rattle Troubleshooting ........... 6
INSTRUMENT PANEL .......................................... 6
CENTER CONSOLE ............................................. 6
DOORS ................................................................. 6
TRUNK .................................................................. 7
SUNROOF/HEADLINING ..................................... 7
SEATS ................................................................... 7
UNDERHOOD ....................................................... 7
Diagnostic Worksheet .............................................. 8
SUNROOF ................................................................ 10
Component Parts and Harness Connector Location ... 10
System Description ................................................. 11
TILT UP / SLIDE CLOSE OPERATION ................ 11
TILT DOWN / SLIDE OPEN OPERATION ........... 11AUTO OPERATION ............................................. 11
TIMER FUNCTION .............................................. 11
ANTI-PINCH FUNCTION .................................... 11
MEMORY RESET PROCEDURE ....................... 12
INITIALIZATION PROCEDURE .......................... 12
Wiring Diagram — SROOF — ................................ 13
Terminals and Reference Value for BCM ............... 14
Terminals and Reference Value for Sunroof Motor
Assembly ................................................................ 14
Work Flow ............................................................... 15
Trouble Diagnosis Chart by Symptom .................... 15
Check BCM Power Supply and Ground Circuit ...... 15
Check Sunroof Motor Assembly Power Supply and
Ground Circuit ........................................................ 16
Check Sunroof Switch System ............................... 17
Check Driver Side Door Switch .............................. 19
Wind Deflector Inspection ....................................... 21
Link and Wire Assembly ......................................... 21
Fitting Adjustment ................................................... 21
LID WEATHERSTRIP OVERLAP ADJUST-
MENT AND SURFACE FLASHNESS ADJUST-
MENT .................................................................. 22
Removal and Installation ........................................ 22
SUNROOF UNIT ASSEMBLY ............................. 24
GLASS LID .......................................................... 25
WEATHERSTRIP OF GLASS LID ....................... 26
SUNSHADE ........................................................ 26
WIND DEFLECTOR ............................................ 26
SUNROOF MOTOR ASSEMBLY ........................ 27
LINK ASSEMBLY AND WIRE ASSEMBLY ......... 27

Page 3166 of 3502

NISSAN TEANA 2003 Service Manual RF-2
PRECAUTIONS

PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
BIS0010L
The Supplemental Restraint System such as “AIR B

RF-2
PRECAUTIONS

PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
BIS0010L
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions BIS0010M
Disconnect both battery cables in advance.
Do not tamper with or force air bag lid open, as this may adversely affect air bag performance.
Be careful not to scratch pad and other parts.
When removing or disassembling any part, be careful not to damage or deform it. Protect parts, which
may get in the way with cloth.
When removing parts with a screwdriver or other tool, protect parts by wrapping them with vinyl or tape.
Keep removed parts protected with cloth.
If a clip is deformed or damaged, replace it.
If an unreusable part is removed, replace it with a new one.
Tighten bolts and nuts firmly to the specified torque.
After re-assembly has been completed, make sure each part functions correctly.
Remove stains in the following way.
Water-soluble stains:
Dip a soft cloth in warm water, and then squeeze it tightly. After wiping the stain, wipe with a soft dry cloth.
Oil stain:
Dissolve a synthetic detergent in warm water (density of 2 to 3% or less), dip the cloth, then clean off the stain
with the cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then clean off the detergent completely.
Then wipe the area with a soft dry cloth.
Do not use any organic solvent, such as thinner or benzine.

Page 3167 of 3502

NISSAN TEANA 2003 Service Manual PREPARATION
RF-3
C
D
E
F
G
H
J
K
L
MA
B
RF

PREPARATIONPFP:00002
Commercial Service ToolsBIS0010N
Tool name Description
Engine ear Locating the noise
SIIA0995E

Page 3168 of 3502

NISSAN TEANA 2003 Service Manual RF-4
SQUEAK AND RATTLE TROUBLE DIAGNOSES

SQUEAK AND RATTLE TROUBLE DIAGNOSESPFP:00000
Work FlowBIS001TK
CUSTOMER INTERVIEW
Interview the customer if possible, to determine the conditions that exist

RF-4
SQUEAK AND RATTLE TROUBLE DIAGNOSES

SQUEAK AND RATTLE TROUBLE DIAGNOSESPFP:00000
Work FlowBIS001TK
CUSTOMER INTERVIEW
Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diag-
nostic Worksheet during the interview to document the facts and conditions when the noise occurs and any
customer's comments; refer to RF-8, "
Diagnostic Worksheet" . This information is necessary to duplicate the
conditions that exist when the noise occurs.
The customer may not be able to provide a detailed description or the location of the noise. Attempt to
obtain all the facts and conditions that exist when the noise occurs (or does not occur).
If there is more than one noise in the vehicle, be sure to diagnose and repair the noise that the customer
is concerned about. This can be accomplished by test driving the vehicle with the customer.
After identifying the type of noise, isolate the noise in terms of its characteristics. The noise characteristics
are provided so the customer, service adviser and technician are all speaking the same language when
defining the noise.
Squeak —(Like tennis shoes on a clean floor)
Squeak characteristics include the light contact/fast movement/brought on by road conditions/hard sur-
faces=higher pitch noise/softer surfaces=lower pitch noises/edge to surface=chirping
Creak—(Like walking on an old wooden floor)
Creak characteristics include firm contact/slow movement/twisting with a rotational movement/pitch
dependent on materials/often brought on by activity.
Rattle—(Like shaking a baby rattle)
Rattle characteristics include the fast repeated contact/vibration or similar movement/loose parts/missing
clip or fastener/incorrect clearance.
Knock —(Like a knock on a door)
Knock characteristics include hollow sounding/sometimes repeating/often brought on by driver action.
Tick—(Like a clock second hand)
Tick characteristics include gentle contacting of light materials/loose components/can be caused by driver
action or road conditions.
Thump—(Heavy, muffled knock noise)
Thump characteristics include softer knock/dead sound often brought on by activity.
Buzz—(Like a bumble bee)
Buzz characteristics include high frequency rattle/firm contact.
Often the degree of acceptable noise level will vary depending upon the person. A noise that you may
judge as acceptable may be very irritating to the customer.
Weather conditions, especially humidity and temperature, may have a great effect on noise level.
SBT842

Load next 8 pages

Page: < prev 1-10 ... 3129-3136 3137-3144 3145-3152 3153-3160 3161-3168 3169-3176 3177-3184 3185-3192 3193-3200 ... 3504 next >

park assist parking sensors timing belt hood release fuel tank removal wheelbase