2003 NISSAN TEANA Service Manual

air suspension compression ratio inflation pressure brake light engine oil

Page 1233 of 3502

NISSAN TEANA 2003 Service Manual UNIFIED METER AND A/C AMP
DI-27
C
D
E
F
G
H
I
J
L
MA
B
DI

UNIFIED METER AND A/C AMPPFP:27760
System DescriptionBKS001SK
For the unified meter and A/C amp., the signal required for con-
trolling the

UNIFIED METER AND A/C AMP
DI-27
C
D
E
F
G
H
I
J
L
MA
B
DI

UNIFIED METER AND A/C AMPPFP:27760
System DescriptionBKS001SK
For the unified meter and A/C amp., the signal required for con-
trolling the combination meter are integrated in the A/C auto
amp.
Unified meter and A/C amp. controls each operation for A/C
auto amp. For information regarding A/C control, refer to AT C -
24, "AIR CONDITIONER CONTROL" .
Unified meter and A/C amp. inputs necessary information for
combination meter from each unit by CAN communication and
so on.
And unified meter and A/C amp. outputs these signals using
communication line (TX, RX) between unified meter and A/C
amp. and combination meter.
The signals required for the distance to empty (DTE) display are centralized in the unified meter and A/C
amp., converted into data, and sent to the display unit (with display unit) using CAN communication.
Other input signals are also sent to the ECM, TCM, BCM and display unit (with display unit) using CAN
communication.
The unified meter and A/C amp. correspond a CONSULT-II function (self-diagnostic results, CAN diag-
nostic support monitor and data monitor).
INPUT/OUTPUT SIGNALS
Between Unified Meter and A/C amp. and Combination Meter
SKIB0778E
Unit Input Output
Unified meter and A/C amp.
Seat belt buckle switch signal (Driver's side)
Parking brake signal
Illumination control nighttime required signal
Refuel status signal
Low-fuel warning lamp condition signal
Combination meter receive error signal
Delivery destination data signal
Combination meter specifications signal
Vehicle speed signal (8-pulse)
Engine speed signal
Engine coolant temperature signal
Fuel level sensor signal (resistance value)
Malfunction indicator lamp signal
ABS warning lamp signal
Brake warning lamp signal
KEY warning lamp signal (With Intelligent Key)
LOCK warning lamp signal (With Intelligent Key)
High-beam request signal
Turn indicator signal
VDC OFF indicator lamp signal (With VDC)
SLIP indicator lamp signal (With VDC)
ASCD CRUISE indicator lamp signal
ASCD SET indicator lamp signal
A/T position indicator signal
A/T CHECK warning lamp signal
CVT indicator lamp signal
CVT position indicator signal
Door switch signal
Oil pressure switch signal
Position lights request signal
Front fog light request signal
Rear fog light request signal
Buzzer output signal

Page 1234 of 3502

NISSAN TEANA 2003 Service Manual DI-28
UNIFIED METER AND A/C AMP

SchematicBKS001SN
TKWM4626E

Page 1235 of 3502

NISSAN TEANA 2003 Service Manual UNIFIED METER AND A/C AMP
DI-29
C
D
E
F
G
H
I
J
L
MA
B
DI

CONSULT-II Function (METER A/C AMP)BKS001SO
CONSULT-II performs the following functions communicating with the unified meter and A/C amp.
CO

UNIFIED METER AND A/C AMP
DI-29
C
D
E
F
G
H
I
J
L
MA
B
DI

CONSULT-II Function (METER A/C AMP)BKS001SO
CONSULT-II performs the following functions communicating with the unified meter and A/C amp.
CONSULT-II BASIC OPERATION
Refer to GI-34, "CONSULT-II Start Procedure"
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which performs CAN communication.
SELF-DIAGNOSTIC RESULTS
Display Item List
“TIME” indicates the condition of the self-diagnostic results judged by each signal input.
Normal: In case of operating properly at the present in spite of having malfunction in the past, then “TIME”
indicates “1-63”.
Malfunction: Soon after detecting malfunctions by self-diagnoses or current malfunction, “0” is indicated.
After returning to normal condition, every time when ignition switch is turned to “OFF” from “ON”, time will be
added like “1”→“2”→“3”···“63”, and when the key operation is performed 64 times, the result of the self-diag-
noses will be erased. And if any malfunction is detected again, “0” will be indicated.
System Diagnosis mode DescriptionReference
page
METER A/C AMPSelf-diagnostic resultsUnified meter and A/C amp. check the conditions and indicates
any error that unified meter and A/C amp. memorized.DI-29
CAN diagnostic support monitorThe results of transmit/receive diagnosis of CAN communication
can be read.LAN-44
Data monitor Displays unified meter and A/C amp. input data in real time.DI-30
Display item [Code] Malfunction is detected when...
CAN COMM CIRC [U1000]Malfunction is detected in CAN communication.
CAUTION:
Even when there is no malfunction on CAN communication system, malfunction may be
misinterpreted when battery has low voltage (when maintaining 7-8V for about 2 seconds)
or 10A fuse [No. 19, located in the fuse block (J/B)] is disconnected.
METER COMM CIRC [B2202]Malfunction is detected in communication of between combination meter and unified meter and
A/C amp.
VEHICLE SPEED CIRC [B2205]When an erroneous speed signal is input for 1 second.
CAUTION:
Even when there is no malfunction on speed signal system, malfunction may be misinter-
preted when battery has low voltage (when maintaining 7-8V for about 2 seconds).

Page 1236 of 3502

NISSAN TEANA 2003 Service Manual DI-30
UNIFIED METER AND A/C AMP

DATA MONITOR
Operation Procedure
1. Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
2. Touch either “MAIN SIGNALS” or “SELECTION FROM MENU” on the

DI-30
UNIFIED METER AND A/C AMP

DATA MONITOR
Operation Procedure
1. Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
2. Touch either “MAIN SIGNALS” or “SELECTION FROM MENU” on the “DATA MONITOR” screen.
3. When “SELECTION FROM MENU” is selected, touch individual
items to be monitored. When “MAIN SIGNALS” is selected,
main items will be monitored.
4. Touch “START”.
5. Touch “RECORD” while monitoring, then the status of the moni-
tored item can be recorded. To stop recording, touch “STOP”.
Display Item List
MAIN SIGNALS Monitors main signals.
SELECTION FROM MENU Selects and monitors individual signal.
SKIA8739E
Monitor item [Unit] MAIN SIGNALSSELECTION
FROM MENUContents
SPEED METER [km/h] or [mph] X XThis is the angle correction value after the speed signal from
the ABS actuator and electric unit (control unit) is converted
into the vehicle speed.
SPEED OUTPUT [km/h] or [mph] X XThis is the angle correction value before the speed signal
from the ABS actuator and electric unit (control unit) is con-
verted into the vehicle speed.
TACHO METER [rpm] X XThis is the converted value for the engine speed signal from
the ECM.
W TEMP METER [°C] or [°F] X XThis is the converted value for the engine coolant tempera-
ture signal from the ECM.
FUEL METER [lit.] X XThis is the processed value for the signal (resistance value)
from the fuel gauge.
DISTANCE [km] or [mile] X XThis is the calculated value for the speed signal from the
ABS actuator and electric unit (control unit), the signal
(resistance signal) from the fuel gauge and fuel consumption
signal from ECM.
FUEL W/L [ON/OFF] X X Indicates [ON/OFF] condition of low-fuel warning lamp.
MIL [ON/OFF] X Indicates [ON/OFF] condition of malfunction indicator lamp.
BUZZER [ON/OFF] X X Indicates [ON/OFF] condition of buzzer.
DOOR W/L [ON/OFF] X Indicates [ON/OFF] condition of door warning lamp.
HI-BEAM IND [ON/OFF] X Indicates [ON/OFF] condition of high-beam indicator.
TURN IND [ON/OFF] X Indicates [ON/OFF] condition of turn indicator.
FR FOG IND X Indicates [ON/OFF] condition of front fog lamp indicator.
RR FOG IND X Indicates [ON/OFF] condition of rear fog lamp.
OIL W/L [ON/OFF] X Indicates [ON/OFF] condition of oil pressure warning lamp.
LIGHT IND [ON/OFF] X Indicates [ON/OFF] condition of light indicator lamp.
VDC/TCS IND [ON/OFF] X Indicates [ON/OFF] condition of VDC OFF indicator lamp.
ABS W/L [ON/OFF] X Indicates [ON/OFF] condition of ABS warning lamp.
SLIP IND [ON/OFF] X Indicates [ON/OFF] condition of SLIP indicator lamp.
BRAKE W/L [ON/OFF] X Indicates [ON/OFF] condition of brake warning lamp.*
KEY G W/L [ON/OFF] X Indicates [ON/OFF] condition of key warning lamp (green).

Page 1237 of 3502

NISSAN TEANA 2003 Service Manual UNIFIED METER AND A/C AMP
DI-31
C
D
E
F
G
H
I
J
L
MA
B
DI

NOTE:
Any monitored item that does not match the vehicle being diagnosed is deleted from the display automatically.
*: Monitor keeps indicat

UNIFIED METER AND A/C AMP
DI-31
C
D
E
F
G
H
I
J
L
MA
B
DI

NOTE:
Any monitored item that does not match the vehicle being diagnosed is deleted from the display automatically.
*: Monitor keeps indicating “OFF” when brake warning lamp is on by the parking brake operation or low brake
fluid level.
KEY R W/L [ON/OFF] X Indicates [ON/OFF] condition of key warning lamp (red).
KEY KNOB W/L [ON/OFF] X Indicates [ON/OFF] condition of key knob warning lamp.
PNP P SW [ON/OFF] X X Indicates [ON/OFF] condition of A/T P range.
PNP N SW [ON/OFF] X X Indicates [ON/OFF] condition of A/T N range.
M-RENGE SW X X Indicates [ON/OFF] condition of manual mode range switch.
NOT M-RANGE SW X XIndicates [ON/OFF] condition of except for manual mode
range switch.
AT-SHIFT UP SW X XIndicates [ON/OFF] condition of manual mode range switch
(up).
AT-SHIFT DOWN SW X XIndicates [ON/OFF] condition of manual mode range switch
(Down).
O/D OFF SW [ON/OFF] X Indicates [ON/OFF] condition of O/D OFF switch.
AT P MODE SW X Indicates [ON/OFF] condition of A/T POWER mode switch.
AT S MODE SW X Indicates [ON/OFF] condition of A/T SNOW mode switch.
BRAKE SW [ON/OFF] XIndicates [ON/OFF] condition of brake switch (Stop lamp
switch).
AT-M IND [ON/OFF] X X Indicates [ON/OFF] condition of manual mode indicator.
AT-M GEAR [5-1] X X Indicates [5-1] condition of manual mode gear position.
P RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift P range indicator.
R RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift R range indicator.
N RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift N range indicator.
D RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift D range indicator.
3 RANGE IND X X Indicates [ON/OFF] condition of A/T shift 3 range indicator.
2 RANGE IND X X Indicates [ON/OFF] condition of A/T shift 2 range indicator.
L RANGE IND X X Indicates [ON/OFF] condition of A/T shift L range indicator.
1 RANGE IND X X Indicates [ON/OFF] condition of A/T shift 1 range indicator.
AT CHECK W/L X Indicates [ON/OFF] condition of AT CHECK warning lamp.
CVT IND X Indicates [ON/OFF] condition of CVT indicator lamp.
CRUISE IND [ON/OFF] X Indicates [ON/OFF] condition of CRUISE indicator.
SET IND [ON/OFF] X Indicates [ON/OFF] condition of SET indicator.Monitor item [Unit] MAIN SIGNALSSELECTION
FROM MENUContents

Page 1238 of 3502

NISSAN TEANA 2003 Service Manual DI-32
UNIFIED METER AND A/C AMP

DTC [U1000] CAN Communication CircuitBKS002B1
1. CHECK CAN COMMUNICATION
1. Select “CAN DIAG SUPPORT MNTR” mode for “METER A/C AMP” with CONSULT-II.
2. Pri

Page 1239 of 3502

NISSAN TEANA 2003 Service Manual UNIFIED METER AND A/C AMP
DI-33
C
D
E
F
G
H
I
J
L
MA
B
DI

5. CHECK VOLTAGE SIGNAL OF COMBINATION METER
1. Turn ignition switch OFF and connect combination meter connector.
2. Turn ignition switch ON

Page 1240 of 3502

NISSAN TEANA 2003 Service Manual DI-34
UNIFIED METER AND A/C AMP

8. CHECK VOLTAGE SIGNAL OF UNIFIED METER AND A/C AMP.
1. Turn ignition switch OFF and connect unified meter and A/C amp. connector.
2. Turn ignition switch ON.
3. Che

Load next 8 pages

Page: < prev 1-10 ... 1201-1208 1209-1216 1217-1224 1225-1232 1233-1240 1241-1248 1249-1256 1257-1264 1265-1272 ... 3504 next >

brake brake pads replacement warning oil additives fuse mileage