Page 777 of 3502
DOOR
BL-119
C
D
E
F
G
H
J
K
L
MA
B
BL
DOORPFP:80100
Fitting AdjustmentBIS000XR
FRONT DOOR
Longitudinal Clearance and Surface Height Adjustment at Front End
1. Remove the fender protector. Refer toEI-23, "FENDER PROTECTOR" .
2. Loosen the hinge mounting bolts. Raise the front door at rear end to adjust.
REAR DOOR
Longitudinal Clearance and Surface Height Adjustment at Front End
1. Remove the center pillar lower garnish. Refer to EI-38, "BODY SIDE TRIM" .
2. Accessing from inside the vehicle, loosen the mounting nuts. Open the rear door, and raise the rear door
at rear end to adjust.
1. Front fender 2. Front door outer 3. Rear door outer
4. Rear fender 5. Front door hinge 6. Bolt
7. Nut 8. Rear door hinge (Upper) 9. Rear door hinge (Lower)
PIIB0277E
Page 778 of 3502

BL-120
DOOR
STRIKER ADJUSTMENT
Adjust the striker so that it becomes parallel with the lock insertion
direction.
Removal and Installation of Front DoorBIS000XS
CAUTION:
When removing and installing the front door assembly, support the door with a jack and cloth to
protect the door and body.
When removing and installing front door assembly, be sure to perform the fitting adjustment Refer
to BL-119, "
Fitting Adjustment" .
Operate with two workers, because of its heavy weight.
Check the hinge rotating part for poor lubrication. If necessary, apply “body grease”.
After installing, check operation.
REMOVAL
1. Disconnect the front door harness connector.
2. Remove the mounting bolts of the check link on the vehicle.
3. Remove the door-side hinge mounting nuts, and remove the
door assembly.
INSTALLATION
Install in the reverse order of removal.
Removal and Installation of Rear DoorBIS000XT
CAUTION:
When removing and installing the rear door assembly, support the door with a jack and cloth to
protect the door and body.
When removing and installing rear door assembly, be sure to perform the fitting adjustment Refer
to BL-119, "
Fitting Adjustment" . : 16.7 N·m (1.7 kg-m, 12 ft-lb)
PIIB1226E
: 14.7 N·m (1.5 kg-m, 11 ft-lb)
PIIB1227E
: 24.5 N·m (2.5 kg-m, 18 ft-lb)
PIIB0279E
Page 779 of 3502
DOOR
BL-121
C
D
E
F
G
H
J
K
L
MA
B
BL
Operate with two workers, because of its heavy weight.
Check the hinge rotating part for poor lubrication. If necessary, apply “body grease”.
After installing, check operation.
REMOVAL
1. Grommet is pulled out, and the Rear door harness connector is detached.
2. Remove the mounting bolts of the check link on the vehicle.
3. Remove the door-side hinge mounting nuts, and remove the
door assembly.
INSTALLATION
Install in the reverse order of removal.
Removal and Installation of Door WeatherstripBIS000XU
REMOVAL
1. Remove the mounting bolts of the check link on the vehicle. Refer to BL-120, "Removal and Installation of
Front Door" or BL-120, "Removal and Installation of Rear Door" .
2. Remove the weatherstrip clips and remove weatherstrip.: 14.7 N·m (1.5 kg-m, 11 ft-lb)
PIIB1227E
: 24.5 N·m (2.5 kg-m, 18 ft-lb)
PIIB0280E
1. Weatherstrip 2. Clip
PIIB0281E
Page 780 of 3502
BL-122
DOOR
INSTALLATION
Install in the reverse order of removal.
Page 781 of 3502
FRONT DOOR LOCK
BL-123
C
D
E
F
G
H
J
K
L
MA
B
BL
FRONT DOOR LOCKPFP:80502
Component StructureBIS000XV
Removal and Installation BIS000XW
REMOVAL
1. Remove the front door finisher. Refer to EI-35, "DOOR FINISHER" .
2. Disconnect inside handle cable and lock knob cable from inside handle.
CAUTION:
During removal and installation, work so as not to bend the
ends of the lock knob cable and inside handle cable.
1. Outside handle 2. Front gasket 3. TORX bolt (T30)
4. Lock knob cable 5. Inside handle 6. Screw
7. Inside handle cable 8. Door lock assembly 9. Outside handle cable
10. Clip 11. Key cylinder connecting rod (Driver
side only)12. TORX bolt (T30)
13. Outside handle bracket 14. TORX bolt (T30) 15. Grommet
16. Rear gasket 17. Door key cylinder assembly (Driver
side)
PIIB0282E
PIIA0632E
Page 782 of 3502
BL-124
FRONT DOOR LOCK
3. Remove the front door glass and front door module assembly. Refer to GW-46, "FRONT DOOR GLASS
AND REGULATOR" .
4. Remove key cylinder connecting rod (key cylinder side). (Driver side only)
5. Disconnect door antenna and door request switch connector
and remove harness clamp. (Models with intelligent key systems
only)
6. Remove door side grommet, and remove door key cylinder assembly (driver side) and outside handle
escutcheon (passenger side) bolts (TORX T30) from grommet hole.
CAUTION:
Do not forcibly remove the TORX bolts (T30).
7. Reach to separate the key cylinder rod connection (on the handle).
8. While pulling the outside handle, remove door key cylinder
assembly (driver side) and outside handle escutcheon (passen-
ger side).
9. While pulling outside handle, slide toward rear of vehicle to
remove outside handle.
10. Remove the front gasket and rear gasket.
PIIB0283E
MIIB0128E
MIIB0129E
MIIB0130E
Page 783 of 3502
FRONT DOOR LOCK
BL-125
C
D
E
F
G
H
J
K
L
MA
B
BL
11. Remove the TORX bolt (T30) of the outside handle bracket.
12. While pulling outside handle bracket, slide toward front of vehi-
cle to remove outside handle bracket.
13. Reach to separate outside handle cable connection.
14. Remove the TORX bolts (T30) of door lock assembly.
15. Disconnect connectors of caught part and door lock assembly, and then remove door lock assembly. :5.8 N·m (0.59 kg-m, 51 in-lb)
PIIB0295E
PIIB0580E
MIIB0134E
MIIB0132E
Page 784 of 3502
BL-126
FRONT DOOR LOCK
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Install each rod by rotating the rod holder until it engages with a tactile feel.
Before installing door lock assembly, apply Anti-Corrosion Wax M-97 Super or equivalent onto
mounting seat on the body.
When installing door lock assembly, be careful so that the outside handle cable bends as shown in
the figure.
Place the outside handle cable on the front of door lock
assembly before installing.
Disassembly and AssemblyBIS000XX
DOOR KEY CYLINDER ASSEMBLY
Removal
Remove the key cylinder escutcheon pawl and remove the door key cylinder.
Installation
Install in the reverse order of removal.
1. Door lock assembly
PIIB0296E
PIIB0284E
1. Door key cylinder assembly 2. Key cylinder escutcheon 3. Door key cylinder
PIIA6431E