Page 577 of 3641
![NISSAN NOTE 2016 Service Repair Manual BRAKE WARNING LAMPBRC-129
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
BRAKE WARNING LAMP
Component Function CheckINFOID:0000000012430911
1.CHECK BRAKE WARNING LAMP FUNCTI NISSAN NOTE 2016 Service Repair Manual BRAKE WARNING LAMPBRC-129
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
BRAKE WARNING LAMP
Component Function CheckINFOID:0000000012430911
1.CHECK BRAKE WARNING LAMP FUNCTI](/manual-img/5/57363/w960_57363-576.png)
BRAKE WARNING LAMPBRC-129
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
BRAKE WARNING LAMP
Component Function CheckINFOID:0000000012430911
1.CHECK BRAKE WARNING LAMP FUNCTION (1)
Check that brake warning lamp in combination mete r turns ON for approximately 2 seconds after ignition
switch is turned ON.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Proceed to diagnosis procedure. Refer to BRC-129, "
Diagnosis Procedure".
2.CHECK BRAKE WARNING LAMP FUNCTION (2)
Check that brake warning lamp in combination meter turns ON/OFF when parking brake is operated.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check parking brake switch system. Refer to BRC-124, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012430912
1.PERFORM THE SELF DIAGNOSTIC
With CONSULT.
Perform “Self Diagnostic Result”.
Are any DTCs detected?
YES >> Refer to BRC-43, "DTC Index".
NO >> GO TO 2.
2.CHECK COMBINATION METER
Check if indication and operation of combination meter are normal. Refer to MWI-10, "
METER SYSTEM : Sys-
tem Description" (TYPE A) or MWI-61, "METER SYSTEM : System Description" (TYPE B).
Is the inspection result normal?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-144, "Removal and Installa-
tion".
NO >> Replace combination meter. Refer to MWI-54, "
Removal and Installation" (TYPE A) or MWI-115,
"Removal and Installation" (TYPE B).
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 578 of 3641
![NISSAN NOTE 2016 Service Repair Manual BRC-130
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
VDC OFF INDICATOR LAMP
VDC OFF INDICATOR LAMP
Component Function CheckINFOID:0000000012430913
1.CHECK VDC OFF INDICA
TOR LAMP FUNCTION
Check that VDC OFF NISSAN NOTE 2016 Service Repair Manual BRC-130
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
VDC OFF INDICATOR LAMP
VDC OFF INDICATOR LAMP
Component Function CheckINFOID:0000000012430913
1.CHECK VDC OFF INDICA
TOR LAMP FUNCTION
Check that VDC OFF](/manual-img/5/57363/w960_57363-577.png)
BRC-130
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
VDC OFF INDICATOR LAMP
VDC OFF INDICATOR LAMP
Component Function CheckINFOID:0000000012430913
1.CHECK VDC OFF INDICA
TOR LAMP FUNCTION
Check that VDC OFF indicator lamp in combination meter turns ON for approximately 2 seconds after ignition
switch is turned ON.
Is the inspection result normal?
YES >> Inspection End.
NO >> Proceed to diagnosis procedure. Refer to BRC-130, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012430914
1.PERFORM THE SELF DIAGNOSTIC
With CONSULT.
Perform “Self Diagnostic Result”.
Are any DTCs detected?
YES >> Refer to BRC-43, "DTC Index".
NO >> GO TO 2.
2.CHECK COMBINATION METER
Check if indication and operation of combination meter are normal. Refer to MWI-10, "
METER SYSTEM : Sys-
tem Description" (TYPE A) or MWI-61, "METER SYSTEM : System Description" (TYPE B).
Is the inspection result normal?
YES >> Replace ABS actuator and electr ic unit (control unit). Refer to BRC-144, "Removal and Installa-
tion".
NO >> Replace combination meter. Refer to MWI-54, "
Removal and Installation" (TYPE A) or MWI-115,
"Removal and Installation" (TYPE B).
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 579 of 3641
![NISSAN NOTE 2016 Service Repair Manual SLIP INDICATOR LAMPBRC-131
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
SLIP INDICATOR LAMP
Component Function CheckINFOID:0000000012430915
1.CHECK SLIP INDICATOR LAMP FUN NISSAN NOTE 2016 Service Repair Manual SLIP INDICATOR LAMPBRC-131
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
SLIP INDICATOR LAMP
Component Function CheckINFOID:0000000012430915
1.CHECK SLIP INDICATOR LAMP FUN](/manual-img/5/57363/w960_57363-578.png)
SLIP INDICATOR LAMPBRC-131
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
SLIP INDICATOR LAMP
Component Function CheckINFOID:0000000012430915
1.CHECK SLIP INDICATOR LAMP FUNCTION
Check that slip indicator lamp in combination meter turns ON for approximately 2 seconds after ignition switch
is turned ON.
Is the inspection result normal?
YES >> Inspection End.
NO >> Proceed to diagnosis procedure. Refer to BRC-131, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012430916
1.PERFORM THE SELF DIAGNOSTIC
With CONSULT.
Perform “Self Diagnostic Result”.
Are any DTCs detected?
YES >> Refer to BRC-43, "DTC Index".
NO >> GO TO 2.
2.CHECK COMBINATION METER
Check if indication and operation of combination meter are normal. Refer to MWI-10, "
METER SYSTEM : Sys-
tem Description" (TYPE A) or MWI-61, "METER SYSTEM : System Description" (TYPE B).
Is the inspection result normal?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-144, "Removal and Installa-
tion".
NO >> Replace combination meter. Refer to MWI-54, "
Removal and Installation" (TYPE A) or MWI-115,
"Removal and Installation" (TYPE B).
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 580 of 3641
![NISSAN NOTE 2016 Service Repair Manual BRC-132
< SYMPTOM DIAGNOSIS >[VDC/TCS/ABS]
VDC/TCS/ABS
SYMPTOM DIAGNOSIS
VDC/TCS/ABS
Symptom TableINFOID:0000000012430917
If ABS warning lamp and SLIP indicator
lamp turn ON, perform self diagnostic. NISSAN NOTE 2016 Service Repair Manual BRC-132
< SYMPTOM DIAGNOSIS >[VDC/TCS/ABS]
VDC/TCS/ABS
SYMPTOM DIAGNOSIS
VDC/TCS/ABS
Symptom TableINFOID:0000000012430917
If ABS warning lamp and SLIP indicator
lamp turn ON, perform self diagnostic.](/manual-img/5/57363/w960_57363-579.png)
BRC-132
< SYMPTOM DIAGNOSIS >[VDC/TCS/ABS]
VDC/TCS/ABS
SYMPTOM DIAGNOSIS
VDC/TCS/ABS
Symptom TableINFOID:0000000012430917
If ABS warning lamp and SLIP indicator
lamp turn ON, perform self diagnostic.
NOTE:
• 1: The ABS does not operate when the speed is 10 km/h (6 MPH) or less.
• 2: Under the following conditions, ABS is activated and vibration is felt when brake pedal is lightly depressed (just place a foot on it).
However, this is normal:
- When shifting gears
- When driving on slippery road
- During cornering at high speed
- When passing over bumps or grooves [approximately 50 mm (1.97 in) or more]
- When pulling away just after starting engine [at approximately 10 km/h (6 MPH) or higher] Symptom
Check itemReference
Excessive ABS function operation fre-
quency Brake force distribution
BRC-133, "
Diag-
nosis Procedure"Looseness of front and rear axle
Wheel sensor and rotor system
Unexpected pedal reaction Brake pedal stroke
BRC-134, "
Diag-
nosis Procedure"Make sure the braking force is sufficient when the ABS is not operating.
The braking distance is long Check stopping distance when the ABS is not operating. BRC-135, "
Diag-
nosis Procedure"
ABS function does not operate (Note 1) ABS actuator and electric
unit (control unit)BRC-136, "Diag-
nosis Procedure"
Pedal vibration or ABS operation sound
occurs (Note 2)Brake pedal
BRC-137, "Diag-
nosis Procedure"ABS actuator and electric unit (control unit)
Vehicle jerks during VDC/TCS/ABS con-
trol ABS actuator and electric unit (control unit)
BRC-138, "
Diag-
nosis Procedure"TCM
ECM
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 581 of 3641
![NISSAN NOTE 2016 Service Repair Manual EXCESSIVE ABS FUNCTION OPERATION FREQUENCYBRC-133
< SYMPTOM DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
EXCESSIVE ABS FUNCTION OPERATION FREQUENCY
Diagnosis ProcedureINFOID:0000000012 NISSAN NOTE 2016 Service Repair Manual EXCESSIVE ABS FUNCTION OPERATION FREQUENCYBRC-133
< SYMPTOM DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
EXCESSIVE ABS FUNCTION OPERATION FREQUENCY
Diagnosis ProcedureINFOID:0000000012](/manual-img/5/57363/w960_57363-580.png)
EXCESSIVE ABS FUNCTION OPERATION FREQUENCYBRC-133
< SYMPTOM DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
EXCESSIVE ABS FUNCTION OPERATION FREQUENCY
Diagnosis ProcedureINFOID:0000000012430918
1.CHECK START
Check front and rear brake force di stribution using a brake tester.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Check brake system.
2.CHECK FRONT AND REAR AXLE
Make sure that there is no excessive play in the front and rear axles. Refer to front: FA X - 7 , "
Inspection", rear:
RAX-5, "
Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace malfunctioning components.
3.CHECK WHEEL SENSOR AND SENSOR ROTOR
Check the following:
• Wheel sensor installation for damage
• Sensor rotor installation for damage
• Wheel sensor connector
• Wheel sensor harness
Is the inspection result normal?
YES >> GO TO 4.
NO >> • Replace wheel sensor BRC-140, "
FRONT WHEEL SENSOR : Removal and Installation" (front)
or BRC-141, "
REAR WHEEL SENSOR : Removal and Installation" (rear).
• Replace sensor rotor BRC-143, "
FRONT SENSOR ROTOR : Removal and Installation" (front)
or BRC-143, "
REAR SENSOR ROTOR : Removal and Installation" (rear).
• Repair harness.
4.CHECK ABS WARNING LAMP DISPLAY
Make sure that the ABS warning lamp is turned off af ter the ignition switch is turned ON or when driving.
Is the inspection result normal?
YES >> Inspection End.
NO >> Perform “Self Diagnostic Result”. Refer to BRC-31, "
CONSULT Function (ABS)".
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 582 of 3641
BRC-134
< SYMPTOM DIAGNOSIS >[VDC/TCS/ABS]
UNEXPECTED PEDAL REACTION
UNEXPECTED PEDAL REACTION
Diagnosis ProcedureINFOID:0000000012430919
1.CHECK BRAKE PEDAL STROKE
Check brake pedal stroke. Refer to BR-9, "
Inspection and Adjustment".
Is the stroke too big?
YES >> • Bleed air from brake line and hose. Refer to BR-13, "Bleeding Brake System".
• Check brake pedal, brake booster, and master cylinder for mount play, looseness, brake system fluid leakage, etc. Refer to brake pedal: BR-9, "
Inspection and Adjustment" or brake booster
assembly BR-15, "
Inspection".
NO >> GO TO 2.
2.CHECK ABS FUNCTION
1. Disconnect ABS actuator and electric unit (control unit) connector to deactivate ABS.
2. Check if braking force is normal in this condition.
3. Reconnect connector after inspection.
Is the inspection result normal?
YES >> Inspection End.
NO >> Check brake system.
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 583 of 3641
THE BRAKING DISTANCE IS LONGBRC-135
< SYMPTOM DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
THE BRAKING DISTANCE IS LONG
Diagnosis ProcedureINFOID:0000000012430920
CAUTION:
The stopping distance on slippery road surfaces might be longer with the ABS operating than when
the ABS is not operating.
1.CHECK ABS FUNCTION
1. Turn ignition switch OFF.
2. Disconnect ABS actuator and el ectric unit (control unit) connector to deactivate ABS.
3. Check stopping distance.
4. After inspection, reconnect connector.
Is the inspection result normal?
YES >> Inspection End.
NO >> Check brake system.
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 584 of 3641
BRC-136
< SYMPTOM DIAGNOSIS >[VDC/TCS/ABS]
ABS FUNCTION DOES NOT OPERATE
ABS FUNCTION DOES NOT OPERATE
Diagnosis ProcedureINFOID:0000000012430921
CAUTION:
ABS does not operate when speed
is 10 km/h (6 MPH) or lower.
1.CHECK ABS WARNING LAMP DISPLAY
Make sure that the ABS warning lamp turns OFF af ter ignition switch is turned ON or when driving.
Is the inspection result normal?
YES >> Inspection End.
NO >> Perform “Self Diagnostic Result”. Refer to BRC-31, "
CONSULT Function (ABS)".
Revision: August 2015 2016 Versa Note
cardiagn.com