Page 1809 of 3641
EXT-42
< REMOVAL AND INSTALLATION >
ROOF SIDE MOLDING
ROOF SIDE MOLDING
Exploded ViewINFOID:0000000012432184
Removal and InstallationINFOID:0000000012432185
ROOF SIDE MOLDING
1. Roof side molding2. Roof side molding clip 3. Roof panel
4. Body side outer panel 5. Double-sided tape
[t: 2.5 mm (0.098 in)] 6. Double-sided tape
[t: 4.0 mm (0.157 in)]
AWKIA2556ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1810 of 3641

ROOF SIDE MOLDINGEXT-43
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
Removal
Lift using a suitable tool (A), then pull the roof side molding from the
roof panel, starting from the front of vehicle and moving toward the
rear.
: Clip
Installation
Installation is in the reverse order of removal.
CAUTION:
Replace the double-sided tape on the back surface with new double-sided tape when reusing the roof
side molding.
ROOF SIDE MOLDING CLIP
Removal
1. Remove roof side molding.
2. Heat double sided tape using a suitable tool, then remove roof side molding clips using a suitable tool.
CAUTION:
Use care not to damage the body paint.
Installation
1. Clean tape removed surface with a shop cloth soaked in white gasoline or IPA.
2. Use two-part epoxy adhesive.
3. Apply adhesive evenly to clip tape surface.
4. Position clip to the proper location, then sufficient ly press-fit until the adhesive protrudes to tape side.
5. Tape clips after press fit to temporarily hold for specified time based on the following conditions.
6. Install roof side molding from rear of vehicle to front after removing the temporary hold tape.
CAUTION:
• When installing roof side moldin g, check that the molding is securely inserted into the clips.
• Do not wash the vehicle within 24 hours so as to keep adhesive dry.
AWKIA2560ZZ
Adhesive : 3M-weld DP–100 or equivalent
Thickness : Approximately 0.5 mm (0.02 in)
Press-fit limit : 19.6 N (2.0 Kg - 4.41 lb) × 2 seconds
5 to 10 °C (41 to 50 °F) : 1 hour or more
11 to 23 °C (52 to 73 °F) : 30 minutes or more
24 °C or more (75 °F or more) : 15 minutes or more
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1811 of 3641
EXT-44
< REMOVAL AND INSTALLATION >
DOOR SASH TAPE
DOOR SASH TAPE
Exploded ViewINFOID:0000000012432186
1. Front door sash front tape 2. Front door sash rear tape 3. Rear door sash front tape
4. Rear door sash rear tape 5. Center pillar tape
JMKIB0613ZZ
Revision: August 20152016 Versa Note
cardiagn.com
Page 1812 of 3641

DOOR SASH TAPEEXT-45
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
Removal and InstallationINFOID:0000000012432187
REMOVAL
Heat door sash tape surface using a suitable tool and remove door sash tape.
CAUTION:
Use care not to damage body paint.
INSTALLATION
CAUTION:
• Degrease door assembly surface for sash tape.
• Grit or dust on surface of sash tape may spoil exterior appearance if not removed. Clean the surface
and check that no grit or dust rema ins before starting the operation.
• Do not reuse blackout tape.
1. Affix door sash tape (2) to door panel (3) by applying pressure using a squeegee (A) while peeling off release coated paper (1).
NOTE:
• Peel release coated paper at distance of 10 – 20 mm (0.4 – 0.8 in) ahead (B) of squeegee and affixblackout paper.
• To prevent any bubbles from forming, slightly lift the portion not yet affixed using a squeegee, so that
portion dose not contact with panel surface. Apply pressure and affix at a low and constant speed using
squeegee tilted at 40 – 50 ° angle (pushing direction) (C) 30 – 45° angle (pulling direction) (D).
2. For small radius portion of hemming part, gradually apply pres- sure and affix door sash tape (1) using squeegee (A) as shown.
CAUTION:
Do not wash the vehicle with in 24 hours so as to keep
adhesive dry.
JMKIA4862GB
JMKIA4655ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1813 of 3641
EXT-46
< REMOVAL AND INSTALLATION >
DOOR OUTSIDE MOLDING
DOOR OUTSIDE MOLDING
Exploded ViewINFOID:0000000012432188
1. Front door outside molding 2. Rear door outside molding 3. Front door panel
AWKIA2517ZZ
Revision: August 20152016 Versa Note
cardiagn.com
Page 1814 of 3641
DOOR OUTSIDE MOLDINGEXT-47
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
Removal and InstallationINFOID:0000000012432189
FRONT DOOR OUTSIDE MOLDING
Removal
1. Lower front door glass fully.
2. Release the pawls using a suitable tool, then rotate front door outside molding toward the outside of the vehicle and lift up to remove.
Installation
Installation is in the reverse order of removal.
REAR DOOR OUTSIDE MOLDING
Removal
1. Lower rear door glass fully.
2. Release the pawl using a suitable tool, then rotate rear door outside molding toward the outside of the
vehicle and lift up to remove.
Installation
Installation is in the reverse order of removal.
4. Rear door panel 5. Rear door glass6. Front door glass
Pawl
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1815 of 3641
EXT-48
< REMOVAL AND INSTALLATION >
BACK DOOR OUTER FINISHER
BACK DOOR OUTER FINISHER
Exploded ViewINFOID:0000000012432190
Removal and InstallationINFOID:0000000012432191
REMOVAL
1. Remove back door inner finisher. Refer to INT-36, "BACK DOOR INNER FINISHER : Removal and Instal-
lation".
2. Disconnect the harness connectors from back door request switch.
3. Remove back door outer finisher nuts.
4. Release clips and remove the back door outer finisher.
5. Remove back door request switch from t he back door outer finisher (if necessary).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
When installing back door finisher, check that clips are securely placed into body panel holes.
1. Rear camera (if equipped) 2. Back door outer finisher 3. Back door request switch
Clip
AWKIA2514ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1816 of 3641
REAR SPOILEREXT-49
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
REAR SPOILER
Exploded ViewINFOID:0000000012432192
Removal and InstallationINFOID:0000000012432193
REMOVAL
1. Open back door.
2. Remove rear spoiler bolt hole covers (1).
3. Remove rear spoiler bolts.
4. Use heat gun and suitable tool to release two way tapes.
5. Release rear spoiler clips and remove rear spoiler.
INSTALLATION
Installation is in reverse order of removal.
NOTE:
1. Rear spoiler 2. Back door3. Back door outer finisher
Clip
ALKIA3634ZZ
ALKIA3639ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com