2016 NISSAN NOTE Service Repair Manual

fuse box diagram lug pattern roof open hood run flat key fob

Page 3369 of 3641

NISSAN NOTE 2016 Service Repair Manual TM-128
< BASIC INSPECTION >[CVT: RE0F11A]
ADDITIONAL SERVICE WHEN REPLACING
CONTROL VALVE OR TRANSAXLE
ASSEMBLY
Is the indicated value of “CALIB DATA” equal to the value shown in the table?
YES

TM-128
< BASIC INSPECTION >[CVT: RE0F11A]
ADDITIONAL SERVICE WHEN REPLACING
CONTROL VALVE OR TRANSAXLE
ASSEMBLY
Is the indicated value of “CALIB DATA” equal to the value shown in the table?
YES >> GO TO 3.
NO >> GO TO 1.
3.LOAD CALIBRATION DATA
1. Shift the selector lever to the “P” position.
2. Check that “P” is displayed on shift position indicator on combination meter. NOTE:
Displayed approximately 4 – 5 seconds after the selector lever is moved to the “P” position.
Does shift position indicator display
“P”?
YES >> GO TO 5.
NO >> GO TO 4.
4.DETECT MALFUNCTIONING ITEMS
Check the following items:
• Harness between the TCM and the ROM assembly insi de the transaxle assembly is open or shorted.
• Disconnected, loose, bent, collapsed, or otherwise abnormal connector housing terminals
Is the inspection result normal?
YES >> GO TO 1.
NO >> Repair or replace the malfunctioning parts.
5.STORE CALIBRATION DATA
1. Turn ignition switch OFF and wait for 5 seconds.
2. Turn ignition switch ON.
Does the shift position indicator display
“P” at the same time when turning ON the ignition switch?
YES >> GO TO 6.
NO >> Check harness between battery and TCM harness connector terminal.
6.ERASE THE CVT FLUID DEGRADATION LEVEL DATA
With CONSULT
1. Select “WORK SUPPORT” in “TRANSMISSION”.
UNIT CLB ID5 00OFFSET2 PRI 0
UNIT CLB ID6 00OFFSET2 H/R 0
UNIT CLB ID7 00OFFSET2 L/B 0
UNIT CLB ID8 00INIT OFFSET H/R A 0
UNIT CLB ID9 00INIT OFFSET H/R B 0
UNIT CLB ID10 00INIT OFFSET H/R C 0
UNIT CLB ID11 00INIT OFFSET H/R D 0
GAIN LU 256INIT OFFSET H/R E 0
GAIN PL 256INIT OFFSET H/R F 0
GAIN PRI 256INIT OFSET LB A 0
GAIN HC/RB 256INIT OFSET LB B 0
GAIN L/B 256INIT OFSET LB C 0
OFFSET LU 0INIT OFSET LB D 0
OFFSET PL 0INIT OFSET LB E 0
OFFSET PRI 0INIT OFSET LB F 0
OFFSET HC/RB 0LB INITIALIZE LEARN −1
OFFSET L/B 0HC INITIALIZE LEARN −1
MAP NO LU 00LB INITIALIZE TEMP FF
MAP NO PL 00LB INITIALIZE TEMP FF
MAP NO PRI 00
Item name
Display value Item nameDisplay value
Revision: August 2015 2016 Versa Note

cardiagn.com

Page 3370 of 3641

NISSAN NOTE 2016 Service Repair Manual ADDITIONAL SERVICE WHEN REPLACING CONTROL VALVE OR TRANSAXLE
ASSEMBLY
TM-129
< BASIC INSPECTION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
2. Select “CONFORM CVTF DETERIORTN”.
3. Touch “C

Page 3371 of 3641

NISSAN NOTE 2016 Service Repair Manual TM-130
< BASIC INSPECTION >[CVT: RE0F11A]
CALIBRATION OF G SENSOR
CALIBRATION OF G SENSOR
DescriptionINFOID:0000000012431046
TCM stores calibration data (inherent characteristic value) of G sensor to

Page 3372 of 3641

NISSAN NOTE 2016 Service Repair Manual STALL TESTTM-131
< BASIC INSPECTION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
STALL TEST
Work ProcedureINFOID:0000000012431048
INSPECTION
1. Check the engine oil level. Replenish if necessary.

Page 3373 of 3641

NISSAN NOTE 2016 Service Repair Manual TM-132
< BASIC INSPECTION >[CVT: RE0F11A]
LINE PRESSURE TEST
LINE PRESSURE TEST
Work ProcedureINFOID:0000000012431049
INSPECTION
1. Check the engine oil level. Replenish if necessary. Refer to
LU-7,

TM-132
< BASIC INSPECTION >[CVT: RE0F11A]
LINE PRESSURE TEST
LINE PRESSURE TEST
Work ProcedureINFOID:0000000012431049
INSPECTION
1. Check the engine oil level. Replenish if necessary. Refer to
LU-7, "Inspection".
2. Check for CVT fluid leaks. Refer to TM-228, "
Inspection".
3. Drive for about 10 minutes to warm up the vehicle so that the CVT fluid temperature is 50 to 80°C (122 to
176° F).
4. Stop the vehicle, apply the parking brake and block the tires.
5. Start the engine.
6. Select “Data Monitor” in “TRANSMISSION”.
7. Select “LINE PRESSURE”.
8. Measure the line pressure at both idle and the stall speed. CAUTION:
Keep brake pedal pressed all the way down during measurement.
NARROWING-DOWN MALFUNCTIONING PARTS
Line pressure : TM-265, "Line Pressure"
Judgment Possible cause
Idle speed Low for all positions
(“P”, “R”, “N”, “D”, “L”)
Possible causes include malfunctions in the pressure supply system and low oil pump output.
For example:
• Oil pump wear
• Damage of chain and sprocket
• Pressure regulator valve or plug sticking or spring fatigue
• Oil strainer
⇒ oil pump ⇒ pressure regulator valve passage oil leak
• Engine idle speed too low
Only low for a specific
position Possible causes include an oil pressure leak in a passage or device related to the position after
the pressure is distributed by the manual valve.
High Possible causes include a sensor malfunction or malfunction in the line pressure adjustment
function.
For example:
• Accelerator pedal position signal malfunction
• CVT fluid temperature sensor malfunction
• Line pressure solenoid malfunction (sticking in OFF state, filter clog, cut line)
• Pressure regulator valve or plug sticking
Stal l s pe ed Line pressure does not
rise higher than the line
pressure for idle.
Possible causes include a sensor malfunction or malfunction in the pressure adjustment func-
tion.
For example:
•TCM malfunction
• Line pressure solenoid malfunction (shorting, sticking in ON state)
• Pressure regulator valve or plug sticking
The pressure rises, but
does not enter the
standard position. Possible causes include malfunctions in the pressure supply system and malfunction in the pres-
sure adjustment function.
For example:
• Oil pump wear
• Line pressure solenoid malfunction (sticking, filter clog)
• Pressure regulator valve or plug sticking
Only low for a specific
position Possible causes include an oil pressure leak in a passage or device related to the position after
the pressure is distributed by the manual valve.
Revision: August 2015
2016 Versa Note

cardiagn.com

Page 3374 of 3641

NISSAN NOTE 2016 Service Repair Manual CVT POSITIONTM-133
< BASIC INSPECTION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
CVT POSITION
InspectionINFOID:0000000012431050
1. Turn ON the ignition switch with the shift selector in the "P"

CVT POSITIONTM-133
< BASIC INSPECTION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
CVT POSITION
InspectionINFOID:0000000012431050
1. Turn ON the ignition switch with the shift selector in the "P" position.
2. Press the shift selector handle button with the brak e pedal depressed, and confirm that the shift selector
can be moved from the "P" position. Also confirm that shift selector will not move from the "P" position
without depressing the brake pedal.
3. Move the shift selector and check for “excessive effort,” “sticking,” “noise” or “rattle”.
4. Confirm that shift selector stops at each position with the feel of engagement when it is moved through all
the positions. Check whether or not the actual position the shift selector is in matches the position shown
by the transaxle body.
5. The method of operating the shift selector to individual positions correctly should be as shown.
• (A): Press shift selector button to operate shift selector, whiledepressing the brake pedal.
• (B): Press shift selector button to operate shift selector.
• (C): Shift selector can be operated without pressing shift selector button.
6. When the shift selector handle button is pressed without apply- ing forward/backward force to the shift selector at “P”, “R”, “N”
and “D” positions, there should be no “sticking” of the button.
7. Confirm the back-up lamps illuminate only when shift selector is placed in the “R” position. Confirm the back-up lamps do not illu-
minate when the shift selector is pushed toward the “R” pos ition side when shift selector is in the “P” or “N”
position.
8. Check that the engine can be started only when the shift selector is in the “P” and “N” positions.
9. Check that the transaxle is locked when t he shift selector is in the "P" position.
AdjustmentINFOID:0000000012431051
1. Move the shift selector to the “P” position.
CAUTION:
Rotate the wheels at least a quarter turn and be certain the transaxle is locked in the "P" position.
2. Remove nut (A) and set manual lever (B) to the “P” position. CAUTION:
Do not apply force to the manual lever.
3. Tighten nuts to the specified torque. Refer to TM-234, "
Exploded
View".
CAUTION:
Do not move the manual lever when tightening.
WCIA0620E
JSDIA1875ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

Page 3375 of 3641

NISSAN NOTE 2016 Service Repair Manual TM-134
< BASIC INSPECTION >[CVT: RE0F11A]
HOW TO ERASE PERMANENT DTC
HOW TO ERASE PERMANENT DTC
DescriptionINFOID:0000000012431052
Permanent DTC can be erased by driving each driving pattern.
ECM reco

Page 3376 of 3641

NISSAN NOTE 2016 Service Repair Manual U0073 COMMUNICATION BUS A OFFTM-135
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
DTC/CIRCUIT DIAGNOSIS
U0073 COMMUNICATION BUS A OFF
DescriptionINFOID:0000000012431053
CAN

Load next 8 pages

Page: < prev 1-10 ... 3337-3344 3345-3352 3353-3360 3361-3368 3369-3376 3377-3384 3385-3392 3393-3400 3401-3408 ... 3648 next >

audio garage door opener brakes remote start radiator oil change