2016 NISSAN NOTE Service Repair Manual

check engine light wipers coolant capacity gas tank size air bleeding oil reset

Page 3385 of 3641

NISSAN NOTE 2016 Service Repair Manual TM-144
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
P0705 TRANSMISSION RANGE SENSOR A
P0705 TRANSMISSION RANGE SENSOR A
DTC LogicINFOID:0000000012431080
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTI

TM-144
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
P0705 TRANSMISSION RANGE SENSOR A
P0705 TRANSMISSION RANGE SENSOR A
DTC LogicINFOID:0000000012431080
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Be careful of the driving speed.
1.PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
1. Start the engine.
2. Maintain the following conditions.
3. Shift the selector lever through entire positions from “P ” to “L”. (Hold the selector lever at each position for
10 seconds or more.)
4. Check the first trip DTC.
Is
“P0705” detected?
YES >> Go to TM-144, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012431081
1.CHECK TCM INPUT SIGNALS
With CONSULT
1. Turn ignition switch ON.
2. Select “Data Monitor” in “TRANSMISSION”.
3. Select “D POSITION SW”, “N POSITION SW”, “R POSITION SW”, “P POSITION SW” and “L POSITION
SW”.
4. Shift the selector lever through entire positions fr om “P” to “L” and check ON/OFF of each monitor item.
DTC Trouble diagnosis name DTC detection conditionPossible causes
P0705 Transmission Range Sensor
A Circuit (PRNDL Input) Two or more range signals simultaneously
stay ON continuously for 5 seconds under the
following diagnosis condition 1 and 2:
• Diagnosis condition 1 (continued for 5 sec-
onds or more)
- TCM power supply voltage: More than 11 V
• Diagnosis condition 2 (continued for 2 sec- onds or more)
- Vehicle speed: Less than 3 km/h (2 MPH)
- Accelerator pedal position: 0.6/8 or less
- Idle switch: ON
- Stop lamp switch: ON • Harness or connector
(Short circuit between transmission
range switch and TCM)
• Transmission range switch
Accelerator pedal position : 0.0/8
Brake pedal : Depressed
Vehicle speed : 0 km/h (0 MPH)
Monitor item Test condition Condition
D POSITION SW Selector lever: “D” position On
Other than the above
Off
Revision: August 2015 2016 Versa Note

cardiagn.com

Page 3386 of 3641

NISSAN NOTE 2016 Service Repair Manual P0705 TRANSMISSION RANGE SENSOR ATM-145
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Without CONSULT
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Turn ignit

P0705 TRANSMISSION RANGE SENSOR ATM-145
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Without CONSULT
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Turn ignition switch ON.
4. Shift the selector lever from “P” to “L” and check voltage between TCM harness connector terminals and ground.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO-1 [“D POSITION SW” is “ON” when selector is not in “D” position. (Or connector terminal 4 is at power
voltage.)]>>GO TO 2.
NO-2 [“N POSITION SW” is “ON” when selector is not in “N” position. (Or connector terminal 5 is at power
voltage.)]>>GO TO 4.
NO-3 [“R POSITION SW” is “ON” when selector is not in “R” position. (Or connector terminal 6 is at power
voltage.)]>>GO TO 6.
NO-4 [“P POSITION SW” is “ON” when selector is not in “P” position. (Or connector terminal 7 is at power
voltage.)]>>GO TO 8.
NO-5 [“L POSITION SW” is “ON” when selector is not in “L” position. (Or connector terminal 2 is at power
voltage.)]>>GO TO 10.
2.CHECK D POSITION SW CIRCUIT (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Check continuity between TCM harness connector terminals.
N POSITION SW Selector lever: “N” position On
Other than the above
Off
R POSITION SW Selector lever: “R” position On
Other than the above
Off
P POSITION SW Selector lever: “P” position On
Other than the above
Off
L POSITION SW Selector lever: “L” position On
Other than the above
Off
+ −Condition Voltage
TCM
Connector Terminal
F44 2
Ground Selector lever: “ L” position Battery voltage
Other than the above
Approx. 0 V
4 Selector lever: “D” position Battery voltage
Other than the above
Approx. 0 V
5 Selector lever: “N” position Battery voltage
Other than the above
Approx. 0 V
6 Selector lever: “R” position Battery voltage
Other than the above
Approx. 0 V
7 Selector lever: “P” pos
ition Battery voltage
Other than the above Approx. 0 V
Monitor item
Test condition Condition
Revision: August 2015 2016 Versa Note

cardiagn.com

Page 3387 of 3641

NISSAN NOTE 2016 Service Repair Manual TM-146
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
P0705 TRANSMISSION RANGE SENSOR A
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace malfunctioning parts.
3.CHECK D POSITION SW CI

Page 3388 of 3641

NISSAN NOTE 2016 Service Repair Manual P0705 TRANSMISSION RANGE SENSOR ATM-147
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
6.CHECK P POSITION SW CIRCUIT (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM c

Page 3389 of 3641

NISSAN NOTE 2016 Service Repair Manual TM-148
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
P0705 TRANSMISSION RANGE SENSOR A
Is the inspection result normal?
YES >> GO TO 12.
NO >> Repair or replace malfunctioning parts.
10.CHECK L POSITION SWI

Page 3390 of 3641

NISSAN NOTE 2016 Service Repair Manual P0705 TRANSMISSION RANGE SENSOR ATM-149
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Is the inspection result normal?
YES >> INSPECTION END
NO >> There is a malfunction of

Page 3391 of 3641

NISSAN NOTE 2016 Service Repair Manual TM-150
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
P0706 TRANSMISSION RANGE SENSOR A
P0706 TRANSMISSION RANGE SENSOR A
DTC LogicINFOID:0000000012431083
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRE

TM-150
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
P0706 TRANSMISSION RANGE SENSOR A
P0706 TRANSMISSION RANGE SENSOR A
DTC LogicINFOID:0000000012431083
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Maintain the following conditions.
3. Shift the selector lever through entire positions from “P ” to “L”. (Hold the selector lever at each position for
35 seconds or more.)
4. Check the first trip DTC.
Is
“P0706” detected?
YES >> Go to TM-150, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012431084
1.ADJUSTMENT OF CONTROL CABLE
Adjust control cable. Refer to TM-232, "
Inspection".
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1. Turn ignition switch ON.
2. Select “Self Diagnostic Results” in “TRANSMISSION”.
3. Touch “Erase”.
4. Perform "DTC CONFIRMATION PROCEDURE". Refer to TM-150, "
DTC Logic".
Is
“P0706” detected?
DTC Trouble diagnosis name DTC detection conditionPossible causes
P0706 Transmission Range Sensor
A Circuit Range/Performance When all of the following conditions are satis-
fied for 30 consecutive seconds:
• All range signals stay OFF
• Power supply voltage: More than 11 V
• Harness or connector
(Open circuit transmission range
switch ignition power supply/open cir-
cuit between transmission range
switch and TCM)
• Transmission range switch
• Control cable
When all of the following conditions are satis-
fied for 5 consecutive seconds:
• All range signals stay OFF
• Power supply voltage: More than 11 V
• Engine speed −
input shaft speed is more
than 200 rpm.
• Input shaft speed is more than 250 rpm.
• CVT fluid temperature: More than 20
°C
(68°F).
Accelerator pedal position : 0.0/8
Brake pedal : Depressed
Vehicle speed : 0 km/h (0 MPH)
Revision: August 2015 2016 Versa Note

cardiagn.com

Page 3392 of 3641

NISSAN NOTE 2016 Service Repair Manual P0706 TRANSMISSION RANGE SENSOR ATM-151
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
YES >> GO TO 3.
NO >> INSPECTION END
3.CHECK POWER CIRCUIT
1. Turn ignition switch OFF.

Load next 8 pages

Page: < prev 1-10 ... 3353-3360 3361-3368 3369-3376 3377-3384 3385-3392 3393-3400 3401-3408 3409-3416 3417-3424 ... 3648 next >

dimensions auxiliary battery location spark plugs replace stop start horn spare wheel