2016 NISSAN NOTE Service Repair Manual

refrigerant type recommended oil fuel child seat catalytic converter ground clearance

Page 3297 of 3641

NISSAN NOTE 2016 Service Repair Manual TM-56
< PRECAUTION >[CVT: RE0F11A]
PRECAUTIONS
General Precautions
INFOID:0000000012430985
• Turn ignition switch OFF an d disconnect the battery cable
from the negative terminal before connecting o

Page 3298 of 3641

NISSAN NOTE 2016 Service Repair Manual PRECAUTIONSTM-57
< PRECAUTION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
On Board Diagnosis (OBD) System of CVT and EngineINFOID:0000000012430986
The ECM has an on board diagnostic system . It

PRECAUTIONSTM-57
< PRECAUTION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
On Board Diagnosis (OBD) System of CVT and EngineINFOID:0000000012430986
The ECM has an on board diagnostic system . It will light up the malfunction indicator lamp (MIL) to warn the
driver of a malfunction causing emission deterioration.
CAUTION:
• Be sure to turn the ignition switch OFF and di sconnect the battery cable from the negative terminal
before any repair or inspection work. The open/s hort circuit of related switches, sensors, solenoid
valves, etc. will cause the MIL to light up.
• Be sure to connect and lock the connectors secure ly after work. A loose (unlocked) connector will
cause the MIL to light up due to an open circuit. (Be sure the connector is free from water, grease,
dirt, bent terminals, etc.)
• Be sure to route and secure the harnesses properly after work. Interference of the harness with a
bracket, etc. may cause the MIL to light up due to a short circuit.
• Be sure to connect rubber tubes properly afte r work. A misconnected or disconnected rubber tube
may cause the MIL to light up due to a malfunction of the EGR system or fuel injection system, etc.
• Be sure to erase the unnecessary malfunction informa tion (repairs completed) from the TCM and
ECM before returning the vehicle to the customer.
Removal and Installation Proc edure for CVT Unit ConnectorINFOID:0000000012430987
REMOVAL
• Rotate bayonet ring (A) counterclockwise. Pull out CVT unit har-
ness connector (B) upward and remove it.
INSTALLATION
1. Align marking (A) on CVT unit harness connector terminal with
marking (B) on bayonet ring. Insert CVT unit harness connector.
2. Rotate bayonet ring clockwise.
3. Rotate bayonet ring clockwise until marking (A) on CVT unit har- ness connector terminal body is aligned with the slit (B) on bayo-
net ring as shown in the figure (correctly fitting condition).
CAUTION:
JSDIA1162ZZ
JPDIA0294ZZ
JPDIA0295ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

Page 3299 of 3641

NISSAN NOTE 2016 Service Repair Manual TM-58
< PRECAUTION >[CVT: RE0F11A]
PRECAUTIONS
• Securely align marking (A) on CVT unit harness connec-
tor terminal body with bayonet ri ng slit (B). Then, be care-
ful not to make a half fit condi

Page 3300 of 3641

NISSAN NOTE 2016 Service Repair Manual PREPARATIONTM-59
< PREPARATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
PREPARATION
PREPARATION
Special Service ToolsINFOID:0000000012430988
The actual shape of the tools may differ from those

Page 3301 of 3641

NISSAN NOTE 2016 Service Repair Manual TM-60
< PREPARATION >[CVT: RE0F11A]
PREPARATION
Drift
a: 53 mm (2.09 in) dia.
b: 50 mm (1.97 in) dia. Installing differential side oil seal
Drift
a: 60 mm (2.36 in) dia.
b: 55 mm (2.17 in) dia. Insta

Page 3302 of 3641

NISSAN NOTE 2016 Service Repair Manual COMPONENT PARTSTM-61
< SYSTEM DESCRIPTION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SYSTEM DESCRIPTION
COMPONENT PARTS
CVT CONTROL SYSTEM
CVT CONTROL SYSTEM : Co mponent Parts LocationINFOID:00

Page 3303 of 3641

NISSAN NOTE 2016 Service Repair Manual TM-62
< SYSTEM DESCRIPTION >[CVT: RE0F11A]
COMPONENT PARTS
*: These components are included in control valve assembly.
No.
Component Function
1ECM Mainly transmits the following signal to TCM via CAN

TM-62
< SYSTEM DESCRIPTION >[CVT: RE0F11A]
COMPONENT PARTS
*: These components are included in control valve assembly.
No.
Component Function
1ECM Mainly transmits the following signal to TCM via CAN communication.
• Engine and CVT integrated control signal
NOTE:
General term for the communication (torque-down permission, torque-
down request, etc.) exchanged between the ECM and TCM.
• Engine speed signal
• Accelerator pedal position signal
• Closed throttle position signal
• N idle instruction signal
Mainly receives the following signals from TCM via CAN communication.
• N idle instruction signal
• Malfunction indicator lamp (MIL) signal
2IPDM E/R Mainly transmits the following signal to TCM via CAN communication.
• A/C compressor feedback signal
3TCM TM-63, "
CVT CONTROL SYSTEM : TCM"
4 Transmission range switchTM-63, "CVT CONTROL SYSTEM : Transmission Range Switch"
5 Primary speed sensor TM-63, "CVT CONTROL SYSTEM : Primary Speed Sensor"
6CVT unit —
7 Control
valve ROM assembly*
TM-63, "
CVT CONTROL SYSTEM : ROM Assembly"
CVT fluid temperature sensor*TM-64, "CVT CONTROL SYSTEM : CVT Fluid Temperature Sensor"
Secondary pressure sensor* TM-65, "CVT CONTROL SYSTEM : Secondary Pressure Sensor"
Primary pressure solenoid valve* TM-65, "CVT CONTROL SYSTEM : Primary Pressure Solenoid Valve"
Low brake solenoid valve* TM-65, "CVT CONTROL SYSTEM : Low Brake Solenoid Valve"
High clutch & reverse brake solenoid
valve*TM-66, "CVT CONTROL SYSTEM : High Clutch & Reverse Brake Sole-
noid Valve"
Torque converter clutch solenoid
valve*
TM-66, "CVT CONTROL SYSTEM : Torque
Converter Clutch Solenoid
Va l v e"
Line pressure solenoid valve* TM-66, "CVT CONTROL SYSTEM : Line Pressure Solenoid Valve"
8 Output speed sensor TM-64, "CVT CONTROL SYSTEM : Output Speed Sensor"
9 Secondary speed sensorTM-63, "CVT CONTROL SYSTEM : Secondary Speed Sensor"
10 G sensor TM-66, "CVT CONTROL SYSTEM : G Sensor"
11 B C MMainly transmits the following signal to TCM via CAN communication.
• Stop lamp switch signal
• Turn indicator signal
12 Overdrive control switch TM-66, "
CVT CONTROL SYSTEM : Overdrive Control Switch"
13 Combination meterMainly transmits the following signal to TCM via CAN communication.
• Overdrive control switch signal
Mainly receives the following signals from TCM via CAN communication.
• Shift position indicator signal
• O/D OFF indicator signal
14 Malfunction indicator lamp (MIL) TM-68, "
CVT CONTROL SYSTEM : Malfunction Indicator Lamp (MIL)"
15 O/D OFF indicator lamp TM-66, "CVT CONTROL SYSTEM : O/D OFF Indicator Lamp"
16 Shift position indicator TM-68, "CVT CONTROL SYSTEM : Shift Position Indicator"
17 ABS actuator and electric unit (control unit)Mainly transmits the following signal to TCM via CAN communication.
• Vehicle spee
d signal (ABS)
• ABS operation signal
• ABS malfunction signal
• TCS malfunction signal
• VDC malfunction signal
Revision: August 2015 2016 Versa Note

cardiagn.com

Page 3304 of 3641

NISSAN NOTE 2016 Service Repair Manual COMPONENT PARTSTM-63
< SYSTEM DESCRIPTION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
CVT CONTROL SYSTEM : TCMINFOID:0000000012430991
• The vehicle driving status is judged based on the signals

Load next 8 pages

Page: < prev 1-10 ... 3265-3272 3273-3280 3281-3288 3289-3296 3297-3304 3305-3312 3313-3320 3321-3328 3329-3336 ... 3648 next >

brake reset infotainment system coolant capacity child lock coolant temperature trip computer