Page 3625 of 3641
WW-60
< REMOVAL AND INSTALLATION >
FRONT WASHER NOZZLE AND TUBE
FRONT WASHER NOZZLE AND TUBE
Exploded ViewINFOID:0000000012433238
WASHER NOZZLE
WASHER NOZZLE : Removal and InstallationINFOID:0000000012433239
REMOVAL
1. Remove cowl top cover. Refer to EXT-37, "Removal and Installation".
2. Disconnect front washer tube fr om front washer nozzle (1).
3. Place cowl top cover (2) up side down and release front washer nozzle pawl (A) using a suitable tool to remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, adjust the nozzle spray pattern. Refer to WW-61, "
WASHER NOZZLE : Adjustment".
1. Front washer nozzle (RH) 2. Front washer tube3. Front washer motor
4. Washer tank 5. Front washer nozzle (LH) A. To rear washer
B. Washer pump seal Clip
ALLIA1306ZZ
AWLIA2161ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3626 of 3641

FRONT WASHER NOZZLE AND TUBEWW-61
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
K
M A
B
WW
N
O P
WASHER NOZZLE : AdjustmentINFOID:0000000012433240
If washer nozzle (1) spray pattern is not within specification, adjust
using a suitable tool (A).
WASHER TUBE
WASHER TUBE : Removal and InstallationINFOID:0000000012433241
REMOVAL
1. Remove fender protector (RH). Refer to EXT-38, "Removal and Installation".
2. Remove front washer tube from washer pump.
3. Remove cowl top cover. Refer to EXT-37, "
Removal and Installation".
4. Release the clips that retain the front washer tube to the vehicle body using a suitable tool and remove.
1. Windshield glass 2. Black printed area line3. Front washer nozzle (LH/RH)
A. Center line B. 509.7 mm (20.07 in)C. 215.7 mm (8.49 in)
D. 614.5 mm (24.19 in) E. 329.1 mm (12.96 in)F. 41.0 mm (1.61 in)
G. 379.6 mm (14.94 in) H. 161.1 mm (6.34 in)J. 58.6 mm (2.31 in)
K. 58.0 mm (2.28 in) M. 142.0 mm (5.59 in)N. 365.9 mm (14.41 in)
O. 54.7 mm (2.15 in) P. 492.5 mm (19.39 in)Q. 652.2 mm (25.68 in)
R. 174.3 mm (6.86 in) S. 520.7 mm (20.50 in)
ALLIA1307ZZ
JMLIA1327ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3627 of 3641
WW-62
< REMOVAL AND INSTALLATION >
FRONT WASHER NOZZLE AND TUBE
INSTALLATION
Installation is in the reverse order of removal.
WASHER TUBE : InspectionINFOID:0000000012433242
INSPECTION
Check that air can pass through the nozzle (1) by blowing into the
nozzle and that air cannot flow in the opposite direction.
O: Air can flow
X: Air cannot flow
JMLIA1326ZZ
Revision: August 20152016 Versa Note
cardiagn.com
Page 3628 of 3641
FRONT WIPER ARMWW-63
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
K
M A
B
WW
N
O P
FRONT WIPER ARM
Exploded ViewINFOID:0000000012433243
Removal and InstallationINFOID:0000000012433244
REMOVAL
1. Open hood.
2. Operate wiper to move it to the auto stop position.
3. Remove wiper arm cap.
4. Remove wiper arm nut and wiper arm.
INSTALLATION
1. Clean wiper arm mount as shown. This will reduce the possibility of wiper arm looseness.
2. Operate wiper motor to move the wiper to the auto stop position.
3. Adjust the front wiper blade position. Refer to WW-64, "
Adjustment".
1. Wiper arm cap (LH/RH)2. Wiper arm (LH)3. Wiper blade (LH)
4. Wiper arm (RH) 5. Wiper blade (RH)6. Front wiper drive
ALLIA1310ZZ
ELH0717D
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3629 of 3641
WW-64
< REMOVAL AND INSTALLATION >
FRONT WIPER ARM
4. Install front wiper arm and front wiper arm nut.CAUTION:
Tighten front wiper arm nut to specification. Refer to WW-63, "
Exploded View".
5. Install front wiper arm cap.
6. Check that wiper blades stop at the specified position. Refer to WW-64, "
Adjustment".
AdjustmentINFOID:0000000012433245
WIPER BLADE POSITION ADJUSTMENT
ALLIA1309ZZ
1. Wiper blade (RH) 2. Front fender (RH) 3. Windshield glass
4. Cowl top cover 5. Wiper blade (LH) C. 28.0 ± 7.5 mm (1.10 ± 0.30 in)
D. 60.7 ± 7.5 mm (2.39 ± 0.30 in)
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3630 of 3641
FRONT WIPER BLADEWW-65
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
K
M A
B
WW
N
O P
FRONT WIPER BLADE
Removal and InstallationINFOID:0000000012433246
REMOVAL
1. Lift up wiper arm and set to the position where wiper arm can be locked back.
2. Push the release tab (A) of the front wiper blade (1), then move the front wiper blade down the front wiper arm (2) to remove.
CAUTION:
Be careful not to drop the wiper arm onto the windshield
glass.
INSTALLATION
Insert the front wiper blade onto the front wiper arm until it clicks into place.
JMLIA1044ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3631 of 3641
WW-66
< REMOVAL AND INSTALLATION >
FRONT WIPER DRIVE ASSEMBLY
FRONT WIPER DRIVE ASSEMBLY
Exploded ViewINFOID:0000000012433247
Removal and InstallationINFOID:0000000012433248
REMOVAL
1. Remove cowl top cover. Refer to EXT-37, "Removal and Installation".
2. Disconnect the harness connector from front wiper motor.
3. Remove bolts and front wiper drive assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Tighten front wiper drive assembly bo lts to specification. Refer to WW-66, "
Exploded View".
1. Wiper arm cap (LH/RH) 2. Wiper arm (LH)3. Wiper blade (LH)
4. Wiper arm (RH) 5. Wiper blade (RH) 6. Front wiper drive assembly
ALLIA1310ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3632 of 3641

FRONT WIPER DRIVE ASSEMBLYWW-67
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
K
M A
B
WW
N
O P
Exploded ViewINFOID:0000000012433249
Disassembly and AssemblyINFOID:0000000012433250
DISASSEMBLY
1. Remove front wiper drive assembly. Refer to WW-66, "Removal and Installation".
2. Remove wiper linkage 1 and 2 from the front wiper drive. CAUTION:
Do not bend the linkage or damage the plastic part of the ball jo int when removing the wiper link-
age.
3. Remove screws and wiper motor from front wiper drive.
ASSEMBLY
1. Install wiper motor screws and wiper motor to front wiper drive.
2. Install wiper linkage 2 to the front wiper drive. CAUTION:
• Do not drop wiper motor or cause it to come into contact with other parts.
• Be careful of the grease condition at the wiper mo tor and wiper linkage joint (retainer). Apply a
suitable multi −purpose grease if necessary.
3. Install wiper linkage 1 to the wiper motor and the front wiper drive.
4. Install front wiper drive assembly. Refer to WW-66, "
Removal and Installation".
1. Wiper linkage 22. Wiper linkage 1 3. Front wiper motor
4. Front wiper drive
ALLIA1311ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com