2016 NISSAN NOTE battery current sensor

BRC-32
< SYSTEM DESCRIPTION >[VDC/TCS/ABS]
DIAGNOSIS SYSTEM [
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
FR RH IN SOL
(On/Off) –
×× Front RH IN ABS solenoid (On/Off) status is dis-
played.
FR RH OUT SOL
(On/Off) –
×× Front RH OUT ABS solenoid (On/Off) status is dis-
played.
FR LH IN SOL
(On/Off) –
×× Front LH IN ABS solenoid (On/Off) status is displayed.
FR LH OUT SOL
(On/Off) –
×× Front LH OUT ABS solenoid (On/Off) status is dis-
played.
RR RH IN SOL
(On/Off) –
×× Rear RH IN ABS solenoid (On/ Off) status is displayed.
RR RH OUT SOL
(On/Off) –
×× Rear RH OUT ABS solenoid (On/Off) status is dis-
played.
RR LH IN SOL
(On/Off) –
×× Rear LH IN ABS solenoid (On/ Off) status is displayed.
RR LH OUT SOL
(On/Off) –
×× Rear LH OUT ABS solenoid (On/Off) status is dis-
played.
EBD WARN LAMP
(On/Off) ––
×Brake warning lamp (On/Off) status is displayed.
STOP LAMP SW
(On/Off) ×× ×
Stop lamp switch (On/Off) status is displayed.
MOTOR RELAY
(On/Off) –
×× ABS motor relay signal (On/Of f) status is displayed.
ACTUATOR RLY
(On/Off) –
×× ABS actuator relay signal (On/ Off) status is displayed.
ABS WARN LAMP
(On/Off) –
×× ABS warning lamp (On/Off) status is displayed.
OFF LAMP
(On/Off) –
×× VDC OFF Lamp (On/Off) status is displayed.
OFF SW ×× × VDC OFF Switch (On/Off) position is displayed
SLIP/VDC LAMP
(On/Off) –
×× SLIP indicator lamp (On/Off) status is displayed.
BATTERY VOLT
(V) ×× × Voltage (V) supplied to ABS actuator and electric unit
(control unit) is displayed.
GEAR
(1, 2, 3, 4, 5) ×× × Gear position (1, 2, 3, 4, 5) judged by transmission
range switch signal is displayed.
SLCT LVR POSI ×× × Curre
nt gear p
osition judged from current gear posi-
tion signal is displayed.
ENGINE SPEED ×× × Engine speed judged by CAN communication signal
is displayed.
YAW R AT E S E N
(d/s) ×× × Yaw rate (d/s) detected by yaw rate sensor is dis-
played.
R POSI SIG
(On/Off) ––
×Reverse shift position (On/Off) judged by transmis-
sion range switch signal.
N POSI SIG
(On/Off) ––
×Neutral position (On/Off) judged by transmission
range switch signal.
P POSI SIG
(On/Off) ––
×Park position (On/Off) judged by transmission range
switch signal.
CV1
(On/Off) ––
×Cut valve 1(On/Off) status is displayed.
CV2
(On/Off) ––
×Cut valve 2 (On/Off) status is displayed.
Item
(Unit) Data monitor item selection
Remarks
ECU INPUT
SIGNALS MAIN
SIGNALS SELECTION
FROM MENU
Revision: August 2015 2016 Versa Note

cardiagn.com

CHG
PRECAUTIONSCHG-3
< PRECAUTION >
C
DE
F
G H
I
J
K L
B A
O P
N
PRECAUTION
PRECAUTIONS
Precaution for Supplemental
Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000012431235
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoper ative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintentional act ivation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipm ent on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identi fied by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Un it or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or el ectric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three mi nutes before performing any service.
Precaution for Power Generation Voltage Variable Control SystemINFOID:0000000012431236
CAUTION:
For model with power generation voltage variable control system, the battery current sensor that is
installed to the battery cable at the negative te rminal measures the charging/discharging current of
the battery, and performs various controls. If the electrical component or the ground wire is connected
directly to the battery terminal, the current othe r than that being measured with the battery current
sensor is charging to or discharging from the battery. This cond ition causes the malfunction of the
control, and then the battery discharge may occur. Do not connect the electrical component or the
ground wire directly to the battery terminal.
Revision: August 2015 2016 Versa Note

cardiagn.com

CHG-6
< SYSTEM DESCRIPTION >
COMPONENT PARTS
Component Description
INFOID:0000000012431240
No. Component part Description
1 IPDM E/R The IPDM E/R converts the received power generation com-
mand value into a pulse width modulated (PWM) command sig-
nal and sends it to the IC regulator.
2ECM The battery current sensor detects the charging/discharging
current of the battery. The ECM judges the battery condition
based on this signal.
The ECM judges whether to request more output via the power
generation voltage variable control according to the battery
condition.
When performing the power generation voltage variable con-
trol, the ECM calculates the target power generation voltage
according to the battery condition and sends the calculated val-
ue as the power generation command value to the IPDM E/R.
3 Battery current sensor The battery current sensor is located on the negative battery
cable terminal. The battery current sensor detects the charg-
ing/discharging current of the battery and sends a voltage sig-
nal to the ECM according to the current value detected.
4 Generator (IC regulator) The IC regulator controls the power generation voltage by the
target power generation voltage based on the received PWM
command signal.
When there is no PWM command signal, the generator per-
forms the normal power generation according to the character-
istic of the IC regulator.
5 Combination meter (charge warning lamp) The IC regulator warning function activates to illuminate the
charge warning lamp if any of the following symptoms occur
while generator is operating:
• Excessive voltage is produced.
• No voltage is produced.
Revision: August 2015
2016 Versa Note

cardiagn.com

CHG-16
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
>> GO TO 2.
2.STOP POWER GENERATION VOLTAGE VARIABLE CONTROL SYSTEM
Stop the operation of the power generation voltage variabl e control in either of the following procedures.
• After selecting “ENGINE” using CONSULT, set the DUTY value of “ALTERNATOR DUTY” to 0 % by select-
ing “ALTERNATOR DUTY” of “Active Test”. Continue “Active Test” until the end of inspection. (When the
DUTY value is 0 or 100 %, the normal power generation is performed according to the characteristic of the
IC regulator of the generator.)
• Turn the ignition switch OFF, and disconnect the batte ry current sensor connector. [However, DTC (P1550–
P1554) of the engine might remain. After finishing the inspection, connect the battery current sensor connec-
tor and erase the self diagnosis results history of the engine using CONSULT.]
>> GO TO 3.
3.DIAGNOSIS WITH EXP-800 NI OR GR8-1200 NI
Perform the charging system test using Multitasking battery and electrical diagnostic station GR8-1200 NI or
Battery and electrical diagnostic analyzer EXP-800 NI. Refer to the applicable Instruction Manual for proper
testing procedures.
Te s t r e s u l t
NO PROBLEMS>>Charging system is normal and will also show “DIODE RIPPLE” test result.
NO VOLTAGE>>GO TO 4.
LOW VOLTAGE>>GO TO 12.
HIGH VOLTAGE>>GO TO 14.
EXCESSIVE RIPPLE, OPEN PHASE, OPEN DIODE or SHORTED DIODE>>Replace the generator. Refer
to CHG-29, "
Removal and Installation". Perform “DIODE RIPPLE” test again using Multitasking
battery and electrical diagnostic station GR8-1200 NI or Battery and electrical diagnostic analyzer
EXP-800 NI to confirm repair.
4.INSPECTION WITH CHARGE WARNING LAMP (IGNITION SWITCH IS ON)
Turn the ignition switch ON.
Does the charge warning lamp illuminate?
YES >> GO TO 6.
NO >> GO TO 5.
5.“L” TERMINAL CIRCUIT (OPEN) INSPECTION
Check “L” terminal circuit (open). Refer to CHG-24, "
Diagnosis Procedure".
Is the
“L” terminal circuit normal?
YES >> Replace generator. Refer to CHG-29, "Removal and Installation".
NO >> Repair as needed.
6.INSPECTION WITH CHARGE WARNING LAMP (IDLING)
Start the engine and run it at idle.
Does the charge warning lamp turn OFF?
YES >> GO TO 9.
NO >> GO TO 7.
7.“L” TERMINAL CIRCUIT (SHORT) INSPECTION
Check “L” terminal circuit (short). Refer to CHG-26, "
Diagnosis Procedure".
Is the
“L” terminal circuit normal?
YES >> GO TO 8.
NO >> Repair as needed.
8.“S” TERMINAL CIRCUIT INSPECTION
Check “S” terminal circuit. Refer to CHG-27, "
Diagnosis Procedure".
Is the
“S” terminal circuit normal?
YES >> GO TO 10.
Revision: August 2015 2016 Versa Note

cardiagn.com

CHG-18
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
• Use fully charged battery.
DETAILED FLOW
1.PRELIMINARY INSPECTION
Perform the preliminary inspection. Refer to CHG-20, "
Diagnosis Procedure".
>> GO TO 2.
2.STOP POWER GENERATION VOLT AGE VARIABLE CONTROL SYSTEM
Stop the operation of the power generation voltage variabl e control in either of the following procedures:
• After selecting “ENGINE” using CONSULT, set the DUTY value of “ALTERNATOR DUTY” to 0 % by select-
ing “ALTERNATOR DUTY” with “Active Test”. Continue “Active Test” until the end of inspection. (When the
DUTY value is 0 or 100 %, the normal power generation is performed according to the characteristic of the
IC regulator of the generator.)
• Turn the ignition switch OFF, and disconnect the batte ry current sensor connector. [However, DTC (P1550 -
P1554) of the engine might remain. After finishing the inspection, connect the battery current sensor connec-
tor and erase the self-diagnostic results history of the engine using CONSULT.]
>> GO TO 3.
3.INSPECTION WITH CHARGE WARNING LAMP (IGNITION SWITCH IS TURNED ON)
When ignition switch is turned ON.
Does the charge warning lamp illuminate?
YES >> GO TO 4.
NO >> GO TO 10.
4.INSPECTION WITH CHARGE WARNING LAMP (IDLING)
Start the engine and run it at idle
Does the charge warning lamp turn OFF?
ALMIA0577GB
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-1
ENGINE
C
DE
F
G H
I
J
K L
M
SECTION EC
A
EC
N
O P
CONTENTS
ENGINE CONTROL SYSTEM
HR16DE
PRECAUTION ....... ........................................
8
PRECAUTIONS .............................................. .....8
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
8
On Board Diagnostic (OBD) System of Engine
and CVT ....................................................................
8
General Precautions .................................................9
PREPARATION ...........................................12
PREPARATION .............................................. ....12
Special Service Tools .......................................... ....12
Commercial Service Tools ......................................12
SYSTEM DESCRIPTION .............................14
COMPONENT PARTS ................................... ....14
ENGINE CONTROL SYSTEM ............................... ....14
ENGINE CONTROL SYSTEM :
Component Parts Location ....................................
14
ENGINE CONTROL SYSTEM : Component De-
scription ............................................................... ....
17
Accelerator Pedal Position Sensor ..........................18
Air Fuel Ratio Sensor 1 ...........................................19
Air Fuel Ratio Sensor 1 Heater ...............................19
Camshaft Position Sensor .......................................19
Clutch Pedal Position Switch ..................................20
Cooling Fan .............................................................20
Crankshaft Position Sensor .....................................20
ECM .................................................................... ....20
Electric Throttle Control Actuator ............................21
Engine Coolant Temperature Sensor ......................21
Engine Oil Pressure Sensor ....................................21
Engine Oil Temperature Sensor ..............................21
EVAP Canister Purge Volume Control Solenoid
Valve ................................................................... ....
22
EVAP Canister Vent Control Valve .........................22
EVAP Control System Pressure Sensor ..................22
Exhaust Valve Timing Cont rol Solenoid Valve ........23
Fuel Injector ......................................................... ....23
Fuel Pump ...............................................................23
Heated Oxygen Sensor 2 ........................................24
Heated Oxygen Sensor 2 Heater ............................24
Ignition Coil With Power Transistor .........................24
Intake Air Temperature Sensor ...............................24
Intake Valve Timing Control Solenoid Valve ...........25
Knock Sensor ...................................................... ....25
Battery Current Sensor (With Battery Tempera-
ture Sensor) .............................................................
25
Malfunction Indicator Lamp (MIL) ............................26
Mass Air Flow Sensor ..............................................26
Oil Pressure Warning Lamp ....................................26
Refrigerant Pressure Sensor ............................... ....27
Stop Lamp Switch & ASCD Brake Switch ...............27
Throttle Control Motor .......................................... ....27
Throttle Control Motor Relay ...................................27
Throttle Position Sensor ..........................................27
ASCD Steering Switch .............................................27
STRUCTURE AND OPERATION .....................28
Positive Crankcase Ventilation ................................28
On Board Refueling Vapor Recovery (ORVR) ........29
SYSTEM ............................................................30
ENGINE CONTROL SYSTEM ........................ ...........30
ENGINE CONTROL SYSTEM : System Diagram ....30
ENGINE CONTROL SYSTEM : System Descrip-
tion ...........................................................................
31
MULTIPORT FUEL INJECTION SYSTEM ................31
MULTIPORT FUEL INJECTION SYSTEM :
System Diagram ................................................. ....
32
MULTIPORT FUEL INJECTION SYSTEM : Sys-
tem Description ........................................................
32
ELECTRIC IGNITION SYSTEM .................................35
ELECTRIC IGNITION SYSTEM :
System Diagram ................................................. ....
35
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-6
Diagnosis Procedure .............................................356
P0850 PNP SWITCH .......................................358
Description ........................................................... ..358
DTC Logic ..............................................................358
Component Function Check ..................................359
Diagnosis Procedure .............................................359
P1078 EVT CONTROL POSITION SENSOR ..361
DTC Logic ............................................................ ..361
Diagnosis Procedure .............................................361
Component Inspection ...........................................363
P1148 CLOSED LOOP CONTROL .................364
DTC Logic ............................................................ ..364
Diagnosis Procedure .............................................364
P1212 TCS COMMUNICATION LINE .............365
Description ........................................................... ..365
DTC Logic ..............................................................365
Diagnosis Procedure .............................................365
P1217 ENGINE OVER TEMPERATURE .........366
DTC Logic ............................................................ ..366
Component Function Check ..................................366
Diagnosis Procedure .............................................367
P1225 TP SENSOR .........................................369
DTC Logic ............................................................ ..369
Diagnosis Procedure .............................................369
P1226 TP SENSOR .........................................370
DTC Logic ............................................................ ..370
Diagnosis Procedure .............................................370
P1550 BATTERY CURRENT SENSOR ..........371
DTC Logic ............................................................ ..371
Diagnosis Procedure .............................................371
Component Inspection ...........................................372
P1551, P1552 BATTERY CURRENT SEN-
SOR ..................................................................
373
DTC Logic ............................................................ ..373
Diagnosis Procedure .............................................373
Component Inspection ...........................................374
P1553 BATTERY CURRENT SENSOR ..........375
DTC Logic ............................................................ ..375
Diagnosis Procedure .............................................375
Component Inspection ...........................................376
P1554 BATTERY CURRENT SENSOR ..........377
DTC Logic ............................................................ ..377
Component Function Check ..................................377
Diagnosis Procedure .............................................378
Component Inspection ...........................................379
P1564 ASCD STEERING SWITCH .................380
DTC Logic ............................................................ ..380
Diagnosis Procedure .............................................380
Component Inspection ...........................................382
P1572 ASCD BRAKE SWITCH ........................383
DTC Logic ............................................................ .383
Diagnosis Procedure .............................................384
Component Inspection (ASCD Brake Switch) .......386
Component Inspection (Stop Lamp Switch) ..........386
P1574 ASCD VEHICLE SPEED SENSOR .......388
Description ........................................................... .388
DTC Logic .............................................................388
Diagnosis Procedure .............................................388
P159F ACTIVE GRILLE SHUTTER .................390
DTC Logic .............................................................390
Diagnosis Procedure .............................................391
P1715 INPUT SPEED SENSOR .......................392
Description ........................................................... .392
DTC Logic .............................................................392
Diagnosis Procedure .............................................392
P1720 VSS ........................................................394
Description ........................................................... .394
DTC Logic .............................................................394
Diagnosis Procedure .............................................394
P1805 BRAKE SWITCH ................................. ..396
DTC Logic ............................................................ .396
Diagnosis Procedure .............................................396
Component Inspection ..........................................397
P2096, P2097 A/F SENSOR 1 .........................398
DTC Logic ............................................................ .398
Diagnosis Procedure .............................................398
P2100, P2103 THROTTLE CONTROL MO-
TOR RELAY .....................................................
402
DTC Logic ............................................................ .402
Diagnosis Procedure .............................................402
P2101 ELECTRIC THROTTLE CONTROL
FUNCTION ........................................................
405
DTC Logic ............................................................ .405
Diagnosis Procedure .............................................405
Component Inspection ..........................................408
P2118 THROTTLE CONTROL MOTOR ..........409
DTC Logic ............................................................ .409
Diagnosis Procedure .............................................409
Component Inspection ..........................................410
P2119 ELECTRIC THROTTLE CONTROL
ACTUATOR ......................................................
411
DTC Logic ............................................................ .411
Diagnosis Procedure .............................................411
P2122, P2123 APP SENSOR ...........................413
DTC Logic ............................................................ .413
Diagnosis Procedure .............................................413
Component Inspection ..........................................414
P2127, P2128 APP SENSOR ...........................416
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-14
< SYSTEM DESCRIPTION >[HR16DE]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
ENGINE CONTROL SYSTEM
ENGINE CONTROL SYSTEM : Component Parts LocationINFOID:0000000012431269
1. Battery current sensor
2. ECM3. IPDM E/R
Refer to PCS-4, "
Component Parts
Location"
4. Mass air flow sensor (with intake air temperature sensor) 5. Electric throttle control actuator
(with built in throttle position sensor
and throttle control motor) 6. EVAP canister purge volume control
solenoid valve
7. Cooling fan motor 8. Refrigerant pressure sensor
Refer to HA-12, "
Component Parts
Location"
ALBIA1071ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com