Page 3457 of 3641
![NISSAN NOTE 2016 Service Repair Manual TM-216
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
MAIN POWER SUPPLY AND GROUND CIRCUIT
5.CHECK CIRCUIT BETWEEN
IPDM E/R AND TCM
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check co NISSAN NOTE 2016 Service Repair Manual TM-216
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
MAIN POWER SUPPLY AND GROUND CIRCUIT
5.CHECK CIRCUIT BETWEEN
IPDM E/R AND TCM
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check co](/manual-img/5/57363/w960_57363-3456.png)
TM-216
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
MAIN POWER SUPPLY AND GROUND CIRCUIT
5.CHECK CIRCUIT BETWEEN
IPDM E/R AND TCM
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness c onnector terminal and TCM harness connector terminals.
Is the check result normal?
YES >> GO TO 6.
NO >> Repair or replace malfunctioning parts.
6.DETECT MALFUNCTIONING ITEMS (PART 2)
Check the following items:
• Open circuit or short circuit in harness between ignition switch and IPDM E/R. Refer to PG-27, "
Wiring Dia-
gram — Ignition Power Supply —".
• Short circuit in harness between IPDM E/R harness connector terminal 21 and TCM harness connector ter-
minal 47, and 48.
• 10A fuse (No.49, IPDM E/R). Refer to PG-60, "
IPDM E/R Terminal Arrangement".
• IPDM E/R
Is the check result normal?
YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> Repair or replace malfunctioning parts.
IPDM E/R TCM
Continuity
Connector Terminal Connector Terminal
E45 21F44 47
Existed
48
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3458 of 3641
![NISSAN NOTE 2016 Service Repair Manual OVERDRIVE CONTROL SWITCHTM-217
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
OVERDRIVE CONTROL SWITCH
Component Function CheckINFOID:0000000012431162
1.CHECK OD OFF INDICATO NISSAN NOTE 2016 Service Repair Manual OVERDRIVE CONTROL SWITCHTM-217
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
OVERDRIVE CONTROL SWITCH
Component Function CheckINFOID:0000000012431162
1.CHECK OD OFF INDICATO](/manual-img/5/57363/w960_57363-3457.png)
OVERDRIVE CONTROL SWITCHTM-217
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
OVERDRIVE CONTROL SWITCH
Component Function CheckINFOID:0000000012431162
1.CHECK OD OFF INDICATOR LAMP FUNCTION
Check OD OFF indicator lamp turns ON for approx. 2 seconds when ignition switch turns ON.
Is the inspection results normal?
YES >> GO TO 2.
NO >> Go to TM-219, "
Diagnosis Procedure".
2.CHECK OVERDRIVE CONT ROL SWITCH FUNCTION
1. Shift the selector lever to “D” position.
2. Check that OD OFF indicator lamp turns ON /OFF when overdrive control switch is operated.
Is the inspection results normal?
YES >> INSPECTION END
NO >> Go to TM-217, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012431163
1.CHECK OVERDRIVE CO NTROL SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect CVT shift selector connector.
3. Turn ignition switch ON.
4. Check voltage between CVT shift selector harness connector terminals.
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 4.
2.CHECK OVERDRIVE CONTROL SWITCH
Check overdrive control switch. Refer to TM-218, "
Component Inspection (Overdrive Control Switch)".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace malfunctioning parts.
3.CHECK GROUND CIRCUIT
Check continuity between CVT shift selector harness connector terminal and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace malfunctioning parts.
4.CHECK CIRCUIT BETWEEN COMB INATION METER AND CVT SHIFT SELECTOR (PART 1)
1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check continuity between combination meter harness connector terminal and CVT shift selector harness connector terminal.
CVT shift selector
Voltag e
(Approx.)
Connector +
−
Te r m i n a l
M38 125 V
CVT shift selector
—Con tin uit y
Connector Terminal
M38 2Ground Existed
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3459 of 3641
![NISSAN NOTE 2016 Service Repair Manual TM-218
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
OVERDRIVE CONTROL SWITCH
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace malfunctioning parts.
5.CHECK CIRCUIT BETWEEN COMBINATI NISSAN NOTE 2016 Service Repair Manual TM-218
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
OVERDRIVE CONTROL SWITCH
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace malfunctioning parts.
5.CHECK CIRCUIT BETWEEN COMBINATI](/manual-img/5/57363/w960_57363-3458.png)
TM-218
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
OVERDRIVE CONTROL SWITCH
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace malfunctioning parts.
5.CHECK CIRCUIT BETWEEN COMBINATION METE
R AND CVT SHIFT SELECTOR (PART 2)
Check continuity between combination meter harness connector terminal and ground.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace malfunctioning parts.
6.CHECK COMBINATION METER INPUT SIGNAL
1. Connect all of disconnected connectors.
2. Turn ignition switch ON.
3. Select “Data Monito r” in “METER/M&A”.
4. Select “O/D OFF SW”.
5. Check that “O/D OFF SW” turns ON/OFF when ov erdrive control switch is operated. Refer to MWI-21,
"Reference Value".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> Replace combination meter. Refer to MWI-54, "
Removal and Installation".
Component Inspection (Overdrive Control Switch)INFOID:0000000012431164
1.CHECK OVERDRIVE CONTROL SWITCH
Check continuity between wires of selector lever knob (1)
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace selector lever knob. Refer to TM-231,
"Removal and Installation".
Combination meterCVT shift selector
Continuity
Connector Terminal Connector Terminal
M24 8M38 1Existed
Combination meter
— Continuity
Connector Terminal
M24 8 Ground Not existed
Condition Continuity
Overdrive control switch is depressed Existed
Overdrive control switch is depressed Not existed
JSDIA1969ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3460 of 3641
![NISSAN NOTE 2016 Service Repair Manual OD OFF INDICATOR LAMPTM-219
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
OD OFF INDICATOR LAMP
Component Function CheckINFOID:0000000012431165
1.CHECK OD OFF INDICATOR LAMP NISSAN NOTE 2016 Service Repair Manual OD OFF INDICATOR LAMPTM-219
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
OD OFF INDICATOR LAMP
Component Function CheckINFOID:0000000012431165
1.CHECK OD OFF INDICATOR LAMP](/manual-img/5/57363/w960_57363-3459.png)
OD OFF INDICATOR LAMPTM-219
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
OD OFF INDICATOR LAMP
Component Function CheckINFOID:0000000012431165
1.CHECK OD OFF INDICATOR LAMP FUNCTION
Check OD OFF indicator lamp turns ON for approx. 2 seconds when ignition switch turns ON.
Is the inspection results normal?
YES >> INSPECTION END
NO >> Go to TM-219, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012431166
1.CHECK DTC (TCM)
With CONSULT
1. Turn ignition switch ON.
2. Check “Self Diagnostic Results” in “TRANSMISSION”.
Is any DTC detected?
YES >> Check DTC detect ed item. Refer to TM-110, "DTC Index".
NO >> GO TO 2.
2.CHECK DTC (COMBINATION METER)
With CONSULT
Check “Self Diagnostic Results” in “METER/M&A”.
Is any DTC detected?
YES >> Check DTC detect ed item. Refer to MWI-24, "DTC Index".
NO >> GO TO 3.
3.CHECK COMBINATION METER INPUT SIGNAL
With CONSULT
1. Shift the selector lever to “D” position.
2. Select “Data Monitor” in “METER/M&A”.
3. Select “O/D OFF IND”.
4. Check that “O/D OFF IND” turns ON/OFF when overdrive control switch is operated. Refer to MWI-21,
"Reference Value".
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-54, "Removal and Installation".
NO >> GO TO 4.
4.CHECK TCM INPUT/OUTPUT SIGNAL
With CONSULT
1. Select “Data Monitor” in “TRANSMISSION”.
2. Select “SPORT MODE SW”.
3. Check that “SPORT MODE SW” tu rns ON/OFF when overdrive control switch is operated. Refer to TM-
99, "Reference Value".
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-54, "Removal and Installation".
NO >> Check overdrive control switch. Refer to TM-217, "
Diagnosis Procedure".
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3461 of 3641
![NISSAN NOTE 2016 Service Repair Manual TM-220
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
SHIFT POSITION INDICATOR CIRCUIT
SHIFT POSITION INDICATOR CIRCUIT
Component Parts Fu
nction InspectionINFOID:0000000012431167
1.CHECK SHIFT POSITION INDI NISSAN NOTE 2016 Service Repair Manual TM-220
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
SHIFT POSITION INDICATOR CIRCUIT
SHIFT POSITION INDICATOR CIRCUIT
Component Parts Fu
nction InspectionINFOID:0000000012431167
1.CHECK SHIFT POSITION INDI](/manual-img/5/57363/w960_57363-3460.png)
TM-220
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
SHIFT POSITION INDICATOR CIRCUIT
SHIFT POSITION INDICATOR CIRCUIT
Component Parts Fu
nction InspectionINFOID:0000000012431167
1.CHECK SHIFT POSITION INDICATOR
1. Start the engine.
2. Shift selector lever.
3. Check that the selector lever position and the shift position indicator on the combination meter are identi-
cal.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Go to TM-220, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012431168
1.CHECK TCM INPUT/OUTPUT SIGNAL
With CONSULT
1. Start the engine.
2. Select “Data Monitor” in “TRANSMISSION”.
3. Select “RANGE”.
4. Shift selector lever.
5. Check that selector lever position, “RANGE” on CONSULT screen, and shift position indicator display on
combination meter are identical.
Is the check result normal?
YES >> INSPECTION END
NO-1 (“RANGE” is changed but is not displayed on shift position indicator.>>Check “Self Diagnostic Result” in “TRANSMISSION”.
NO-2 (“RANGE” and shift position indicator are differ ent.)>>Check “Self Diagnostic Result” in “TRANSMIS-
SION”.
NO-3 (Specific“RANGE” is not displayed on shift position indicator.)>>Check “Self Diagnostic Result” in
“METER/M&A”.
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3462 of 3641
![NISSAN NOTE 2016 Service Repair Manual SHIFT LOCK SYSTEMTM-221
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SHIFT LOCK SYSTEM
Component Function CheckINFOID:0000000012431169
1.CHECK SHIFT LOCK OPERATIO N (BRAKE NISSAN NOTE 2016 Service Repair Manual SHIFT LOCK SYSTEMTM-221
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SHIFT LOCK SYSTEM
Component Function CheckINFOID:0000000012431169
1.CHECK SHIFT LOCK OPERATIO N (BRAKE](/manual-img/5/57363/w960_57363-3461.png)
SHIFT LOCK SYSTEMTM-221
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SHIFT LOCK SYSTEM
Component Function CheckINFOID:0000000012431169
1.CHECK SHIFT LOCK OPERATIO N (BRAKE PEDAL RELEASED)
1. Ignition switch ON.
2. Attempt to shift selector lever to any position other than “P” position with brake pedal released.
Can the selector lever be shifted?
YES >> Go to TM-221, "Diagnosis Procedure".
NO >> GO TO 2.
2.CHECK SHIFT LOCK OPERATIO N (BRAKE PEDAL APPLIED)
Attempt to shift the selector lever to any pos ition other than “P” position with brake pedal applied.
Can the selector lever be shifted?
YES >> Inspection End.
NO >> Go to TM-221, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012431170
1.CHECK STOP LAMP SWITCH
1. Ignition switch ON.
2. Check voltage between stop lamp switch connector E13 terminal 4 and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK GROUND CIRCUIT
1. Ignition switch OFF.
2. Disconnect CVT shift selector connector.
3. Check continuity between CVT shift selector connector M38 terminal 6 and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace ground circuit.
3.CHECK STOP LAMP SWITCH POWER CIRCUIT
Check voltage between stop lamp switch connector E13 terminal 3 and ground.
Is the inspection result normal?
YES >> Replace stop lamp switch.
NO >> Repair or replace power circuit.
Stop lamp switch Ground Brake pedal Voltage
Connector Terminal
E13 4Ground Applied
Battery voltage
Released 0V
CVT shift selector
GroundContinuity
Connector Terminal
M38 6Ground Yes
Stop lamp switch
GroundVoltage
Connector Terminal
E13 3GroundBattery voltage
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3463 of 3641
TM-222
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
SHIFT LOCK SYSTEM
4.CHECK CVT SHIFT SELECTOR POWER CIRCUIT
Check voltage between CVT shift selector connector M38 terminal 5 and ground.
Is the inspection result normal?
YES >> Replace CVT shift selector. Refer to TM-231, "Removal and Installation".
NO >> Repair or replace power circuit.
CVT shift selector GroundBrake pedal Voltage
Connector Terminal
M38 5Ground AppliedBattery voltage
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3464 of 3641
![NISSAN NOTE 2016 Service Repair Manual CVT CONTROL SYSTEMTM-223
< SYMPTOM DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SYMPTOM DIAGNOSIS
CVT CONTROL SYSTEM
Symptom TableINFOID:0000000012431171
The diagnosis item number indica NISSAN NOTE 2016 Service Repair Manual CVT CONTROL SYSTEMTM-223
< SYMPTOM DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SYMPTOM DIAGNOSIS
CVT CONTROL SYSTEM
Symptom TableINFOID:0000000012431171
The diagnosis item number indica](/manual-img/5/57363/w960_57363-3463.png)
CVT CONTROL SYSTEMTM-223
< SYMPTOM DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SYMPTOM DIAGNOSIS
CVT CONTROL SYSTEM
Symptom TableINFOID:0000000012431171
The diagnosis item number indicates the order of check. Start checking in the order from 1.
Symptom diagnosis chart 1-1
SymptomCheck under on board condition (repair
and part replacement) Replace the transaxle assembly.
Engine system
Incorrect adjustment of CVT fluid level
Line pressure is out of the standard value.
Control cable
Electric system
TCM
Overdrive control switch
Primary speed sensor (P0715)
Secondary speed sensor (P2765)
Output speed sensor (P0720)
Transmission position switch (P0705, P0706)
Secondary pressure sensor (P0846, P0847, P0848)
Primary pressure soleno
id valve (P17BA, P17BB)
Line pressure solenoid valve (P0746, P0962, P0963)
Lock-up solenoid valve
(P0740, P0743, P0744)
High clutch &reverse brake solenoid valve
(P1739, P173C, P17B7, P17B8)
Low brake solenoid valve
(P173A, P173B, P17B4, P17B5)
CVT fluid temperature sensor (P0711, P0712, P0713)
EC-120
TM-229TM-131TM-232TM-99TM-217TM-110
Driving is
not possi-
ble. The engine speed increases in
“D”, “L”, or “R” position, but the
vehicle cannot start.
11111 11 12 1 1 1 2
Engine stall occurs in “D”, “L”,
or “R” position and the vehicle
does not start. 11 11 1111 1 1 2
Acceleration at start is not suf-
ficient in “D”, “L”, or “R” posi-
tion. 1 2 1 1112211 2 1 1 1
The engine speed increases
suddenly in “D”, “L”, or “R” po-
sition during driving. 11
211 1 1
Engine brake is suddenly ap-
plied in “D” or “R” position dur-
ing driving. 11
11 11
Revision: August 2015 2016 Versa Note
cardiagn.com