Page 137 of 5121
MEMORY INDICATE DOES NOT OPERATE
ADP-131
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
K
L
MA
B
ADP
N
O
P
MEMORY INDICATE DOES NOT OPERATE
Diagnosis ProcedureINFOID:0000000003759224
1.CHECK MEMORY INDICATOR
Check memory indicator.
Refer to ADP-76, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-35, "Intermittent Incident".
NO >> GO TO 1.
Page 138 of 5121

ADP-132
< SYMPTOM DIAGNOSIS >
ENTRY/EXIT ASSIST FUNCTION DOES NOT OPERATE
ENTRY/EXIT ASSIST FUNCTION DOES NOT OPERATE
Diagnosis ProcedureINFOID:0000000003759233
1.CHECK SYSTEM SETTING
1. Check system setting.
Refer to ADP-10, "
SYSTEM SETTING : Special Repair Requirement".
2. Check the operation.
Is the inspection result normal?
YES >> Entry/Exit function is OK.
NO >> GO TO 2.
2.PERFORM SYSTEM INITIALIZATION
1. Perform system initialization.
Refer to ADP-8, "
SYSTEM INITIALIZATION : Special Repair Requirement".
2. Check the operation.
Is the inspection result normal?
YES >> Entry/Exit function is OK.
NO >> GO TO 3.
3.CHECK DTC
Selector lever in Position signal, ignition position signal and key slot signal.
“Self Diagnostic Result” with BCM. Refer to ADP-110, "
DTCIndex".
“Self Diagnostic Result” with TCM. Refer to TM-121, "
DTC Index".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace the malfunctioning parts.
4.CHECK FRONT DOOR SWITCH (DRIVER SIDE)
Check front door switch (driver side).
Refer to ADP-58, "
Component Function Check".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace the malfunctioning parts.
5.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-35, "Intermittent Incident".
NO >> GO TO 1.
Page 139 of 5121
INTELLIGENT KEY INTERLOCK FUNCTION DOES NOT OPERATE
ADP-133
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
K
L
MA
B
ADP
N
O
P
INTELLIGENT KEY INTERLOCK FUNCTION DOES NOT OPERATE
Diagnosis ProcedureINFOID:0000000003759234
1.CHECK DOOR LOCK FUNCTION
Check door lock function.
Refer to DLK-7, "
Work Flow".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.PERFORM MEMORY STORING PROCEDURE
1. Perform memory storing procedure.
Refer to ADP-9, "
MEMORY STORING : Special Repair Requirement".
2. Check Intelligent Key interlock function.
Refer to ADP-31, "
INTELLIGENT KEY INTERLOCK FUNCTION : System Description".
Is the inspection result normal?
YES >> Intelligent Key inter lock function is normal.
NO >> Replace driver seat control unit. Refer to ADP-136, "
Removal and Installation".
Page 140 of 5121

ADP-134
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
DescriptionINFOID:0000000003759236
The following symptoms are normal operations, and they do not indicate a malfunction.
Symptom Cause Action to take Reference page
Entry/exit assist function and
seat synchronization do not op-
erate. No initialization has been performed. Perform initialization.ADP-8
Entry/exit assist function is disabled.
NOTE:
The entry/exit assist function and seat
synchronization function are disabled be-
fore delivery (initial setting).Change the settings.ADP-9
Entry assist function does not op-
erate.Manual operation with power seat switch
was performed after exit assist function
execution.Perform the memory
function.ADP-27
Memory function, entry/exit as-
sist function, or Intelligent Key in-
terlock function does not
operate.The operating conditions are not fulfilled.Fulfill the operation
conditions.Memory function:
ADP-19Exit assist function:
ADP-23
Entry assist function:
ADP-27
Intelligent Key interlock
function: ADP-31
Page 141 of 5121

PRECAUTIONS
ADP-135
< PRECAUTION >
C
D
E
F
G
H
I
K
L
MA
B
ADP
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003940050
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIRBAG” and
“SEAT BELT” of this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
Page 142 of 5121
ADP-136
< ON-VEHICLE REPAIR >
DRIVER SEAT CONTROL UNIT
ON-VEHICLE REPAIR
DRIVER SEAT CONTROL UNIT
Exploded ViewINFOID:0000000003759238
Refer to SE-89, "Exploded View".
Removal and InstallationINFOID:0000000003759239
REMOVAL
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
1. Remove the driver seat (1). Refer to SE-92, "
Removal and
Installation".
2. Remove the mounting nut (A).
3. Remove driver seat control unit (2).
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be sure to clump the harness to the right place.
NOTE:
After installing the driver seat, perform additional service when replacing control unit. Refer to ADP-7, "
ADDI-
TIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description".
JMJIA1449ZZ
Page 143 of 5121
SEAT MEMORY SWITCH
ADP-137
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
MA
B
ADP
N
O
P
SEAT MEMORY SWITCH
Exploded ViewINFOID:0000000003759242
Refer to INT-30, "DRIVER SIDE : Exploded View".
Removal and InstallationINFOID:0000000003759243
REMOVAL
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
1. Remove the seat memory finisher (1). Refer to INT-30, "
DRIVER
SIDE : Removal and Installation".
2. Press pawls and remove seat memory switch (2) from seat
memory finisher, with flat-bladed screw driver (A).
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be sure to clump the harness to the right place.
NOTE:
After installing the driver seat, perform additional service when removing battery negative terminal. Refer to
ADP-7, "
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Description".
:Pawl
JMJIA1817ZZ
Page 144 of 5121
ADP-138
< ON-VEHICLE REPAIR >
POWER SEAT SWITCH
POWER SEAT SWITCH
Exploded ViewINFOID:0000000003940128
Refer to SE-89, "Exploded View".
Removal and InstallationINFOID:0000000003940129
REMOVAL
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
1. Remove the seat cushion outer finisher (1). Refer to SE-92, "
Removal and Installation".
2. Remove switch knob.
3. Remove screws (A).
4. Remove the power seat switch (2) from the seat cushion outer
finisher.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be sure to clump the harness to the right place.
JMJIA1952ZZ