Page 313 of 5121
![NISSAN TEANA 2008 Service Manual AV
PRECAUTIONS
AV-169
< PRECAUTION >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE NISSAN TEANA 2008 Service Manual AV
PRECAUTIONS
AV-169
< PRECAUTION >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE](/manual-img/5/57391/w960_57391-312.png)
AV
PRECAUTIONS
AV-169
< PRECAUTION >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003960542
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIRBAG” and
“SEAT BELT” of this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
Precaution for Trouble DiagnosisINFOID:0000000003882788
AV COMMUNICATION SYSTEM
Do not apply voltage of 7.0 V or higher to the measurement terminals.
Use the tester with its open terminal voltage being 7.0 V or less.
Be sure to turn ignition switch OFF and disconnect the battery cable from the negative terminal before
checking the circuit.
Precaution for Harness RepairINFOID:0000000003882789
AV COMMUNICATION SYSTEM
Solder the repaired parts, and wrap with tape. [Frays of twisted line
must be within 110 mm (4.33 in).]
Do not perform bypass wire connections for the repair parts. (The
spliced wire will become separated and the characteristics of
twisted line will be lost.)
PKIA0306E
PKIA0307E
Page 314 of 5121
AV-170
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
AV CONTROL UNIT
ON-VEHICLE REPAIR
AV CONTROL UNIT
Exploded ViewINFOID:0000000003940154
REMOVAL
Refer to IP-11, "Exploded View".
DISASSEMBLY
Removal and InstallationINFOID:0000000003940155
REMOVAL
1. Remove instrument finisher C. Refer to IP-12, "Removal and Installation".
2. Remove cluster lid D. Refer to IP-12, "
Removal and Installation".
3. Remove AV control unit with A/C amp. as a single unit from the body.
4. Remove bracket screws, and then remove AV control unit.
INSTALLATION
Installation is the reverse order of removal.
1. AV control unit 2. Bracket LH 3. A/C auto amp.
4. Bracket RH
JPNIA1034ZZ
Page 315 of 5121
AV
DISPLAY UNIT
AV-171
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
DISPLAY UNIT
Exploded ViewINFOID:0000000003940156
REMOVAL
Refer to IP-11, "Exploded View".
DISASSEMBLY
Removal and InstallationINFOID:0000000003940157
REMOVAL
1. Remove cluster lid D. Refer to IP-12, "Removal and Installation".
2. Remove display unit mounting screws, and then disconnect the display unit connector.
3. Remove display unit.
INSTALLATION
Installation is the reverse order of removal.
JPNIA1035ZZ
1. Display unit
Page 316 of 5121
AV-172
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
FRONT DOOR SPEAKER
FRONT DOOR SPEAKER
Exploded ViewINFOID:0000000003940158
Removal and InstallationINFOID:0000000003940159
REMOVAL
1. Remove front door finisher. Refer to INT-30, "DRIVER SIDE : Removal and Installation" (driver side) or
INT-33, "
PASSENGER SIDE : Removal and Installation" (passenger side).
2. Remove front door speaker mounting bolts, disconnect the front door speaker connector.
3. Remove front door speaker.
INSTALLATION
Installation is the reverse order of removal.
JPNIA1036ZZ
1. Front door speaker
Page 317 of 5121
AV
REAR DOOR SPEAKER
AV-173
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
REAR DOOR SPEAKER
Exploded ViewINFOID:0000000003940160
Removal and InstallationINFOID:0000000003940161
REMOVAL
1. Remove rear door finisher. Refer to INT-36, "Removal and Installation".
2. Remove rear door speaker mounting bolts, disconnect the rear door speaker connector.
3. Remove rear door speaker.
INSTALLATION
Installation is the reverse order of removal.
JPNIA1037ZZ
1. Rear door speaker
Page 318 of 5121
AV-174
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
FRONT SQUAWKER
FRONT SQUAWKER
Exploded ViewINFOID:0000000003940162
Removal and InstallationINFOID:0000000003940163
REMOVAL
1. Remove the speaker grille with squawker. Refer to IP-12, "Removal and Installation".
2. Remove front squawker mounting screws, lift up the front squawker and disconnect front squawker con-
nector.
3. Remove front squawker.
INSTALLATION
Installation is the reverse order of removal.
JPNIA1038ZZ
1. Front squawker
Page 319 of 5121
AV
ANTENNA AMP.
AV-175
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
ANTENNA AMP.
Exploded ViewINFOID:0000000003940164
Removal and InstallationINFOID:0000000003940165
REMOVAL
1. Remove rear side pillar finisher. Refer to INT-39, "Removal and Installation".
2. Disconnect antenna feeder connector and clip.
3. Remove antenna amp. mounting nut, disconnect the antenna amp. connector.
4. Remove antenna amp.
INSTALLATION
Installation is the reverse order of removal.
JPNIA1032ZZ
1. AM-FM main connector
2. Antenna amp.
Page 320 of 5121
AV-176
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
MULTIFUNCTION SWITCH
MULTIFUNCTION SWITCH
Exploded ViewINFOID:0000000003940166
REMOVAL
Refer to IP-11, "Exploded View".
DISASSEMBLY
Removal and InstallationINFOID:0000000003940167
REMOVAL
1. Remove cluster lid D. Refer to IP-12, "Removal and Installation".
2. Remove multifunction switch mounting screws.
3. Remove multifunction switch.
INSTALLATION
Installation is the reverse order of removal.
JPNIA1052ZZ
1. Cluster lid D
2. Multifunction switch