Page 4225 of 5121
SPIRAL CABLE
SR-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
MA
B
SR
N
O
P
After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Refer to SRC-10, "
Diagnosis Description".
Page 4226 of 5121
SR-12
< ON-VEHICLE REPAIR >
FRONT PASSENGER AIR BAG MODULE
FRONT PASSENGER AIR BAG MODULE
Exploded ViewINFOID:0000000003838669
Removal and InstallationINFOID:0000000003838670
WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes.
Always work from the side of air bag module. Never work in front of it.
Never use air tools or electric tools for servicing.
REMOVAL
1. Remove the instrument panel assembly. Refer to IP-12, "Removal and Installation".
2. Remove the front passenger air bag module fixing screws (A).
3. Disconnect pawls by using remover tool, and then remove front
passenger air bag module (2) from instrument panel (1).
CAUTION:
1. Instrument panel assembly 2. Front passenger air bag module
Refer to GI-4, "
Components" for symbols in the figure.
JMHIA0619GB
: Pawl
JMHIA0621ZZ
Page 4227 of 5121

FRONT PASSENGER AIR BAG MODULE
SR-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
MA
B
SR
N
O
P
Always place front passenger air bag module (1) with pad side
facing upward.
Never impact the front passenger air bag module.
Replace the front passenger air bag module if it has been
dropped or sustained an impact.
Never insert any foreign objects (screwdriver, etc.) into front passenger air bag module.
Never disassembly front passenger air bag module.
Never expose the front passenger air bag module to temperatures exceeding 90°C (194°F).
Never allow oil, grease, detergent or water to come in contact with the front passenger air bag mod-
ule.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Never use old fixing bolts after removal; replace with new bolts.
In the case that a malfunction is detected by the air bag warning lamp, after repair or replacement of
the malfunctioning parts, reset the memory by self-diagnosis or by CONSULT-III.
After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Refer to SRC-10, "
Diagnosis Description".
: Upward
JMHIA0622ZZ
JMHIA0009ZZ
Page 4228 of 5121

SR-14
< ON-VEHICLE REPAIR >
SIDE CURTAIN AIR BAG MODULE
SIDE CURTAIN AIR BAG MODULE
Exploded ViewINFOID:0000000003838671
Removal and InstallationINFOID:0000000003838672
WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes.
Never use air tools or electric tools for servicing.
REMOVAL
1. Remove the headlining assembly.
Normal roof models: Refer to INT-50, "
NORMAL ROOF : Removal and Installation".
Sunroof models: Refer to INT-54, "
SUNROOF : Removal and Installation".
2. Remove the side curtain air bag harness connector.
NOTE:
For installing/removing side curtain air bag harness connector,
insert thin screwdriver wrapped in tape into notch, lift lock and
remove connector.
Install connector with lock raised, and push lock into connec-
tor.
After installing the connector, check that the lock is pushed
securely into it.
1. Side curtain air bag module
Refer to GI-4, "
Components" for symbols in the figure.
JMHIA0623GB
PHIA0953J
Page 4229 of 5121

SIDE CURTAIN AIR BAG MODULE
SR-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
MA
B
SR
N
O
P
3. Remove fixing bolts, and then remove side curtain air bag module.
CAUTION:
Never impact the side curtain air bag module.
Replace the side curtain air bag module if it has been dropped
or sustained an impact.
Never insert any foreign objects (screwdriver, etc.) into side curtain air bag module.
Never disassemble side curtain air bag module.
Never expose the side curtain air bag module to temperatures exceeding 90°C (194°F).
Never allow oil, grease, detergent or water to come in contact with the side curtain air bag module.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
In the case that a malfunction is detected by the air bag warning lamp, after repair or replacement of
the malfunctioning parts, reset the memory by self-diagnosis or by CONSULT-III.
After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Refer to SRC-10, "
Diagnosis Description".
JMHIA0009ZZ
Page 4230 of 5121

SR-16
< ON-VEHICLE REPAIR >
FRONT SIDE AIR BAG MODULE
FRONT SIDE AIR BAG MODULE
Exploded ViewINFOID:0000000003857353
Removal and InstallationINFOID:0000000003857354
REMOVAL
WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes.
Always work from the rear of air bag module.
Never use air tools or electric tools for servicing.
1. Remove the front seat.
With VENTILATION SEAT: Refer to SE-92, "
Removal and Installation".
Without VENTILATION SEAT: Refer to SE-135, "
Removal and Installation".
2. Remove the seatback trim and pad.
With VENTILATION SEAT: Refer to SE-93, "
Disassembly and Assembly".
Without VENTILATION SEAT: Refer to SE-135, "
Disassembly and Assembly".
3. Remove the seatback finisher fixing screws, and then remove seatback finisher.
4. Disconnect the front side air bag harness connector and harness clips.
5. Remove the side air bag module fixing nut, and then remove side air bag module.
CAUTION:
1. Seat frame assembly 2. Side air bag module bracket 3. Side air bag module
4. Seatback finisher
Refer to GI-4, "
Components" for symbols in the figure.
JMHIA0649GB
Page 4231 of 5121

FRONT SIDE AIR BAG MODULE
SR-17
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
MA
B
SR
N
O
P
Always place front side air bag module with pad side facing
upward.
Never impact the air bag module.
Replace the air bag module if it has been dropped or sus-
tained an impact.
Never insert any foreign objects (screwdriver, etc.) into front side air bag module.
Never disassemble front side air bag module.
Never expose the air bag module to temperatures exceeding 90°C (194°F).
Never allow oil, grease, detergent or water to come in contact with the air bag module.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Never use old fixing nut after removal; replace with new nut.
Never damage the air bag harness.
If any malfunction is detected by the air bag warning lamp, reset by the self-diagnosis function and
delete the memory by CONSULT-III.
If any malfunction is still detected after the above operations, perform self-diagnosis to repair mal-
functions.
After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Refer to SRC-10, "
Diagnosis Description".
: Upward
JMHIA0274ZZ
JMHIA0009ZZ
Page 4232 of 5121
SR-18
< ON-VEHICLE REPAIR >
CRASH ZONE SENSOR
CRASH ZONE SENSOR
Exploded ViewINFOID:0000000003838673
Removal and InstallationINFOID:0000000003838674
WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes.
Never use air tools or electric tools for servicing.
REMOVAL
1. Remove the air duct (inlet). Refer to EM-26, "Removal and Installation".
2. Remove radiator hose clamp (1) mounting nut (A).
1. Crash zone sensor
: Vehicle front
Refer to GI-4, "
Components" for symbols in the figure.
JMHIA0624GB
: Vehicle front
JMHIA0632ZZ