Page 1433 of 5121
![NISSAN TEANA 2008 Service Manual TRUNK LID
DLK-217
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
TRUNK LID HINGE : Exploded ViewINFOID:0000000003819765
TRUNK LID HINGE : Removal and InstallationI NISSAN TEANA 2008 Service Manual TRUNK LID
DLK-217
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
TRUNK LID HINGE : Exploded ViewINFOID:0000000003819765
TRUNK LID HINGE : Removal and InstallationI](/manual-img/5/57391/w960_57391-1432.png)
TRUNK LID
DLK-217
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
TRUNK LID HINGE : Exploded ViewINFOID:0000000003819765
TRUNK LID HINGE : Removal and InstallationINFOID:0000000003813418
REMOVAL
1. Remove trunk lid assembly. Refer to DLK-214, "TRUNK LID ASSEMBLY : Removal and Installation".
2. Remove trunk lid stay from trunk lid hinge. Refer to DLK-218, "
TRUNK LID STAY : Removal and Installa-
tion".
3. Remove trunk lid hinge mounting nuts (body side), and then remove trunk lid hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check trunk lid open/close, lock/unlock operation after installation.
Check trunk lid hinge rotating part for poor lubrication. If necessary, apply body grease.
When removing and installing trunk lid assembly, perform the fitting adjustment. Refer to DLK-215,
"TRUNK LID ASSEMBLY : Adjustment".
After installation, apply touch-up paint (the body color) onto the head of trunk lid hinge mounting
bolts.
TRUNK LID STAY
1. Trunk lid 2. Trunk lid weather-strip 3. Cap
4. Stopper 5. Trunk lid hinge 6. Trunk lid striker
7. Bumper rubber 8. Trunk lid lock assembly 9. Trunk lid stay
A : Center mark (upper) B. : Center mark (lower)
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2389GB
Page 1434 of 5121
![NISSAN TEANA 2008 Service Manual DLK-218
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID
TRUNK LID STAY : Exploded View
INFOID:0000000003819766
TRUNK LID STAY : Removal and InstallationINFOID:0000000003813420
REMOVAL
1. NISSAN TEANA 2008 Service Manual DLK-218
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID
TRUNK LID STAY : Exploded View
INFOID:0000000003819766
TRUNK LID STAY : Removal and InstallationINFOID:0000000003813420
REMOVAL
1.](/manual-img/5/57391/w960_57391-1433.png)
DLK-218
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID
TRUNK LID STAY : Exploded View
INFOID:0000000003819766
TRUNK LID STAY : Removal and InstallationINFOID:0000000003813420
REMOVAL
1. Support trunk lid with the proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the trunk lid open when removing the trunk
lid stay.
2. Remove the metal clip (3) located on the connection between
the trunk lid stay (1) and the stud ball (2) (trunk lid side) by using
a flat-bladed screwdriver (A).
3. Remove trunk lid stay (trunk lid side).
4. In the same way, remove trunk lid stay (body side).
INSTALLATION
Install in the reverse order of removal.
1. Trunk lid 2. Trunk lid weather-strip 3. Cap
4. Stopper 5. Trunk lid hinge 6. Trunk lid striker
7. Bumper rubber 8. Trunk lid lock assembly 9. Trunk lid stay
A : Center mark (upper) B.: Center mark (lower)
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2389GB
JMKIA2255ZZ
Page 1435 of 5121
![NISSAN TEANA 2008 Service Manual TRUNK LID
DLK-219
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
CAUTION:
Check trunk lid open/close operation after installation.
TRUNK LID WEATHER-STRIP
TRUNK LI NISSAN TEANA 2008 Service Manual TRUNK LID
DLK-219
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
CAUTION:
Check trunk lid open/close operation after installation.
TRUNK LID WEATHER-STRIP
TRUNK LI](/manual-img/5/57391/w960_57391-1434.png)
TRUNK LID
DLK-219
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
CAUTION:
Check trunk lid open/close operation after installation.
TRUNK LID WEATHER-STRIP
TRUNK LID WEATHER-STRIP : Exploded ViewINFOID:0000000003819767
TRUNK LID WEATHER-STRIP : Removal and InstallationINFOID:0000000003813422
REMOVAL
Pull up and remove engagement with body from weather-strip joint.
CAUTION:
Never pull strongly on weather-strip.
INSTALLATION
1. Working from the upper section, align weather-strip center mark (upper) with vehicle center position mark
and install weather-strip onto the vehicle.
2. For the lower section, align weather-strip center mark (lower) with center of trunk lid striker.
3. Pull weather-strip gently to ensure that there is no loose section.
NOTE:
Check that weather-strip fits tightly in each corner.
1. Trunk lid 2. Trunk lid weather-strip 3. Cap
4. Stopper 5. Trunk lid hinge 6. Trunk lid striker
7. Bumper rubber 8. Trunk lid lock assembly 9. Trunk lid stay
A : Center mark (upper) B. : Center mark (lower)
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2389GB
Page 1436 of 5121
DLK-220
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
HOOD LOCK
HOOD LOCK
Exploded ViewINFOID:0000000003813423
Removal and InstallationINFOID:0000000003813424
REMOVAL
CAUTION:
Check wiring of hood lock control cable before removal.
1. Remove mounting bolts, and then remove hood lock assembly
(1).
NOTE:
Press the lever downward to avoid pin (A), then pull out hood
lock assembly upward.
2. Disconnect hood lock control cable (2) from hood lock assembly.
3. Disconnect bell crank assembly cable from hood lock assembly.
4. Remove air duct (inlet). Refer to EM-26, "
Removal and Installation".
5. Disconnect hood switch connector and remove hood lock assembly.
6. Remove bolts and remove bell crank assembly.
1. Hood lock 2. Hood switch 3. Bell crank assembly
4. Hood lock control cable 5. Hood lock opener
: Clip
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2381ZZ
JMKIA1914ZZ
Page 1437 of 5121
![NISSAN TEANA 2008 Service Manual HOOD LOCK
DLK-221
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
7. Disconnect hood lock control cable from instrument lower panel (LH).
8. Remove fender protector NISSAN TEANA 2008 Service Manual HOOD LOCK
DLK-221
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
7. Disconnect hood lock control cable from instrument lower panel (LH).
8. Remove fender protector](/manual-img/5/57391/w960_57391-1436.png)
HOOD LOCK
DLK-221
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
7. Disconnect hood lock control cable from instrument lower panel (LH).
8. Remove fender protector (LH). Refer to EXT-22, "
FENDER PROTECTOR : Removal and Installation".
9. Remove hood lock control cable clamp.
10. Remove grommet on the lower dash, and pull the hood lock control cable toward the passenger compart-
ment.
CAUTION:
While pulling, never damage (peeling) the outside of hood lock control cable.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Never bend cable too much. Keeping the radius 100 mm (3.937 in) or more.
Check that cable is not offset from the positioning grommet,
and apply the sealant to the grommet (A) properly.
Check that hood lock control cable is properly engaged with hood lock.
After installation, perform hood fitting adjustment. Refer to DLK-193, "
HOOD ASSEMBLY : Adjust-
ment".
After installation, perform hood lock control inspection. Refer to DLK-221, "
Inspection".
InspectionINFOID:0000000003813425
NOTE:
If the hood lock cable is bent or deformed, replace it.
1. Check that secondary latch is properly engaged with secondary striker [6.8 mm (0.268 in)] by hood
weight.
2. While operating hood opener, carefully check that the front end of hood is raised by approximately 20.0
mm (0.787 in). Also check that hood opener returns to the original position.
3. Check that hood opener operating is condition 49 N (5.0 kg, 11.0 lb) or below.
4. Install so that static closing force of hood is 94 – 490 N (9.6 – 50.0 kg, 21.1 – 110 lb).
NOTE:
Exert vertical force on right side and left side of hood lock.
Do not simultaneously press both sides.
5. Check the hood lock lubrication condition. If necessary, apply body grease to hood lock.
JMKIA2398ZZ
Page 1438 of 5121
![NISSAN TEANA 2008 Service Manual DLK-222
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
FRONT DOOR LOCK
DOOR LOCK
DOOR LOCK : Exploded ViewINFOID:0000000003813426
DOOR LOCK : Removal and InstallationINFOID:0000000 NISSAN TEANA 2008 Service Manual DLK-222
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
FRONT DOOR LOCK
DOOR LOCK
DOOR LOCK : Exploded ViewINFOID:0000000003813426
DOOR LOCK : Removal and InstallationINFOID:0000000](/manual-img/5/57391/w960_57391-1437.png)
DLK-222
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
FRONT DOOR LOCK
DOOR LOCK
DOOR LOCK : Exploded ViewINFOID:0000000003813426
DOOR LOCK : Removal and InstallationINFOID:0000000003813427
REMOVAL
1. Remove front door finisher. Refer to INT-30, "DRIVER SIDE : Removal and Installation" (driver side) or
INT-33, "
PASSENGER SIDE : Removal and Installation" (passenger side).
2. Remove front door glass. Refer to GW-17, "
Removal and Installation".
3. Remove front door module assembly. Refer to GW-20, "
Removal and Installation".
4. Remove outside handle and outside handle bracket. Refer to DLK-224, "
OUTSIDE HANDLE : Removal
and Installation".
5. Remove door lock assembly TORX bolts.
6. Disconnect door lock actuator connector, and then remove door lock assembly.
7. Remove key rod from door lock assembly.
INSTALLATION
Install in the reverse order of removal.
1. Outside handle 2. Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)3. Rear gasket
4. TORX bolt 5. Key rod (driver side) 6. Door lock assembly
7. Inside handle escutcheon 8. Inside handle 9. Seal
10. Outside handle bracket 11. Front gasket
: Vehicle front
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2386GB
Page 1439 of 5121
![NISSAN TEANA 2008 Service Manual FRONT DOOR LOCK
DLK-223
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
CAUTION:
When installing each rod, rotate rod holder until a click is felt.
Check door o NISSAN TEANA 2008 Service Manual FRONT DOOR LOCK
DLK-223
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
CAUTION:
When installing each rod, rotate rod holder until a click is felt.
Check door o](/manual-img/5/57391/w960_57391-1438.png)
FRONT DOOR LOCK
DLK-223
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
CAUTION:
When installing each rod, rotate rod holder until a click is felt.
Check door open/close, lock/unlock operation after installation.
INSIDE HANDLE
INSIDE HANDLE : Exploded ViewINFOID:0000000003817716
INSIDE HANDLE : Removal and InstallationINFOID:0000000003813429
REMOVAL
1. Remove front door finisher. Refer to INT-30, "DRIVER SIDE : Removal and Installation" (driver side) or
INT-33, "
PASSENGER SIDE : Removal and Installation" (passenger side).
2. Disconnect inside handle cable.
3. Remove inside handle mounting screws, and then remove the inside handle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
1. Outside handle 2. Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)3. Rear gasket
4. TORX bolt 5. Key rod (driver side) 6. Door lock assembly
7. Inside handle escutcheon 8. Inside handle 9. Seal
10. Outside handle bracket 11. Front gasket
: Vehicle front
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2386GB
Page 1440 of 5121
![NISSAN TEANA 2008 Service Manual DLK-224
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
OUTSIDE HANDLE : Exploded View
INFOID:0000000003817718
OUTSIDE HANDLE : Removal and InstallationINFOID:0000000003813431
REMOV NISSAN TEANA 2008 Service Manual DLK-224
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
OUTSIDE HANDLE : Exploded View
INFOID:0000000003817718
OUTSIDE HANDLE : Removal and InstallationINFOID:0000000003813431
REMOV](/manual-img/5/57391/w960_57391-1439.png)
DLK-224
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
OUTSIDE HANDLE : Exploded View
INFOID:0000000003817718
OUTSIDE HANDLE : Removal and InstallationINFOID:0000000003813431
REMOVAL
1. Remove front door finisher. Refer to INT-30, "DRIVER SIDE : Removal and Installation" (driver side) or
INT-33, "
PASSENGER SIDE : Removal and Installation" (passenger side).
2. Remove front door glass. Refer to GW-17, "
Removal and Installation".
3. Remove front door module assembly. Refer to GW-20, "
Removal and Installation".
4. Disconnect door antenna and door request switch connector and remove harness clamp (models with
Intelligent Key system) on outside handle bracket.
1. Outside handle 2. Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)3. Rear gasket
4. TORX bolt 5. Key rod (driver side) 6. Door lock assembly
7. Inside handle escutcheon 8. Inside handle 9. Seal
10. Outside handle bracket 11. Front gasket
: Vehicle front
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2386GB