Page 3065 of 5121

CENTER CONSOLE ASSEMBLY
IP-25
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
MA
B
IP
N
O
P
12. Remove instrument lower cover RH.
Disengage instrument lower cover LH (1) fixing clip, pawl and
metal clips.
Pull the instrument lower cover RH crosswise.
13. Remove selector lever knob. Refer to TM-155, "
Removal and Installation".
14. Remove console switch panel.
Disengage pawls of console switch panel (1) with remover tool
(A).
Pull up console switch panel.
15. Remove console finisher assembly.
Put selector lever in the [N] position.
Remove console finisher assembly (1) fixing metal clips and
pawls sequentially from the front side with remover tool.
Pull console finisher assembly, upward to disengage from cen-
ter console.
Disconnect harness connectors.
16. Remove control device upper case.
Put selector lever in the [P] position.
Remove control device upper case (1) mounting screws (A).
Pull control device upper case, upward to disengage from con-
trol device assembly.
Disconnect harness clip (B).
17. Remove console rear finisher.
Pull back console rear finisher (1) by using a remover tool (A),
then disengage pawls and metal clips.
Disconnect inside key antenna connector.
: Clip
: Pawl
: Metal clip
JMJIA1903ZZ
: Pawl
JMJIA1904ZZ
: Pawl
: Metal clip
JMJIA1905ZZ
JMJIA1906ZZ
: Pawl
: Metal clip
JMJIA1907ZZ
Page 3066 of 5121
IP-26
< ON-VEHICLE REPAIR >
CENTER CONSOLE ASSEMBLY
18. Remove center console assembly.
Remove center console fixing screws (A).
Put front seat to the front most position.
Remove center console fixing screws (B).
Put front seat to the rear most position.
Lift up center console assembly back side.
Disconnect harness connectors.
INSTALLATION
Install in the reverse order of removal.
Disassembly and AssemblyINFOID:0000000003816781
DISASSEMBLY
1. Remove center console assembly. Refer to IP-22, "Removal and Installation".
2. Remove console lid assembly.
Open the console lid.
Remove console mask (1) fixing pawls with remover tool (A).
JMJIA1908ZZ
JMJIA1909ZZ
: Pawl
JMJIA1925ZZ
Page 3067 of 5121
CENTER CONSOLE ASSEMBLY
IP-27
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
MA
B
IP
N
O
P
Remove console lid assembly (1) fixing screws (A) and then
remove console lid assembly.
3. Remove power outlet. Refer to PWO-8, "
Removal and Installation".
4. Remove auxiliary input jacks. Refer to AV-663, "
Removal and Installation".
ASSEMBLY
Assemble in the reverse order of disassembly.
JMJIA1926ZZ
Page 3068 of 5121

LAN
LAN-1
ELECTRICAL & POWER CONTROL
C
DE
F
G H
I
J
K L
B
SECTION LAN
A
O P
N
CONTENTS
LAN SYSTEM
CAN FUNDAMENTAL
PRECAUTION ................ ...............................
4
PRECAUTIONS .............................................. .....4
Precautions for Trouble Diagnosis ...................... ......4
Precautions for Harness Repair ................................4
FUNCTION DIAGNOSIS ...............................5
CAN COMMUNICATION SYSTEM ................ .....5
System Description ............................................. ......5
System Diagram ........................................................5
CAN Communication Control Circuit .........................6
DIAG ON CAN .....................................................7
Description .......................................................... ......7
System Diagram ........................................................7
TROUBLE DIAGNOSIS ......................................8
Condition of Error Detection ................................ ......8
Symptom When Error Occurs in CAN Communi-
cation System ...................................................... ......
8
CAN Diagnosis with CONSULT-III ..........................11
Self-Diagnosis .........................................................11
CAN Diagnostic Support Monitor ............................11
How to Use CAN Communication Signal Chart ......13
BASIC INSPECTION ...................................14
DIAGNOSIS AND REPAIR WORKFLOW ..... ....14
Trouble Diagnosis Flow Chart ............................. ....14
Trouble Diagnosis Procedure ..................................14
CAN
HOW TO USE THIS MANU AL .....................
19
HOW TO USE THIS SECTION ....................... ....19
Caution ................................................................ ....19
Abbreviation List ......................................................19
PRECAUTION ..............................................20
PRECAUTIONS .................................................20
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ....
20
Precautions for Trouble Diagnosis ..........................20
Precautions for Harness Repair ..............................20
BASIC INSPECTION ...................................21
DIAGNOSIS AND REPAIR WORKFLOW ........21
Interview Sheet .................................................... ....21
FUNCTION DIAGNOSIS ..............................22
CAN COMMUNICATION SYSTEM ...................22
CAN System Specification Chart ......................... ....22
CAN Communication Signal Chart ..........................22
COMPONENT DIAGNOSIS .........................26
CAN COMMUNICATION SYSTEM ...................26
Component Parts Location .................................. ....26
Wiring Diagram - CAN SYSTEM - ...........................27
MALFUNCTION AREA CHART ........................31
Main Line ............................................................. ....31
Branch Line .............................................................31
Short Circuit .............................................................31
MAIN LINE BETWEEN ADP AND M&A CIR-
CUIT ..................................................................
32
Diagnosis Procedure ...............................................32
MAIN LINE BETWEEN M&A AND DLC CIR-
CUIT ..................................................................
33
Diagnosis Procedure ...............................................33
MAIN LINE BETWEEN DLC AND ABS CIR-
CUIT ..................................................................
34
Diagnosis Procedure ...............................................34
ECM BRANCH LINE CIRCUIT .........................35
Diagnosis Procedure ...............................................35
Page 3069 of 5121

LAN-2
ADP BRANCH LINE CIRCUIT ..........................36
Diagnosis Procedure ..............................................36
AV BRANCH LINE CIRCUIT .............................37
Diagnosis Procedure ..............................................37
HVAC BRANCH LINE CIRCUIT ........................38
Diagnosis Procedure ..............................................38
M&A BRANCH LINE CIRCUIT ..........................39
Diagnosis Procedure ..............................................39
STRG BRANCH LINE CIRCUIT ........................40
Diagnosis Procedure ..............................................40
BCM BRANCH LINE CIRCUIT ..........................41
Diagnosis Procedure ..............................................41
DLC BRANCH LINE CIRCUIT ...........................42
Diagnosis Procedure ..............................................42
ABS BRANCH LINE CIRCUIT ..........................43
Diagnosis Procedure ..............................................43
TCM BRANCH LINE CIRCUIT ..........................44
Diagnosis Procedure ..............................................44
IPDM-E BRANCH LINE CIRCUIT .....................45
Diagnosis Procedure ..............................................45
CAN COMMUNICATION CIRCUIT ....................46
Diagnosis Procedure ..............................................46
CAN SYSTEM (TYPE 2)
COMPONENT DIAGNOSIS ........................
48
MAIN LINE BETWEEN M&A AND DLC CIR-
CUIT ...................................................................
48
Diagnosis Procedure ..............................................48
MAIN LINE BETWEEN DLC AND ABS CIR-
CUIT ...................................................................
49
Diagnosis Procedure ..............................................49
ECM BRANCH LINE CIRCUIT ..........................50
Diagnosis Procedure ..............................................50
HVAC BRANCH LINE CIRCUIT ........................51
Diagnosis Procedure ..............................................51
M&A BRANCH LINE CIRCUIT ..........................52
Diagnosis Procedure ..............................................52
BCM BRANCH LINE CIRCUIT ..........................53
Diagnosis Procedure ..............................................53
DLC BRANCH LINE CIRCUIT ...........................54
Diagnosis Procedure ..............................................54
ABS BRANCH LINE CIRCUIT ..........................55
Diagnosis Procedure ..............................................55
TCM BRANCH LINE CIRCUIT ..........................56
Diagnosis Procedure ...............................................56
IPDM-E BRANCH LINE CIRCUIT .....................57
Diagnosis Procedure ...............................................57
CAN COMMUNICATION CIRCUIT ...................58
Diagnosis Procedure ...............................................58
CAN SYSTEM (TYPE 4)
COMPONENT DIAGNOSIS .......................
60
MAIN LINE BETWEEN M&A AND DLC CIR-
CUIT ...................................................................
60
Diagnosis Procedure ...............................................60
MAIN LINE BETWEEN DLC AND ABS CIR-
CUIT ...................................................................
61
Diagnosis Procedure ...............................................61
ECM BRANCH LINE CIRCUIT ..........................62
Diagnosis Procedure ...............................................62
AV BRANCH LINE CIRCUIT .............................63
Diagnosis Procedure ...............................................63
HVAC BRANCH LINE CIRCUIT ........................64
Diagnosis Procedure ...............................................64
M&A BRANCH LINE CIRCUIT ..........................65
Diagnosis Procedure ...............................................65
STRG BRANCH LINE CIRCUIT ........................66
Diagnosis Procedure ...............................................66
BCM BRANCH LINE CIRCUIT ..........................67
Diagnosis Procedure ...............................................67
DLC BRANCH LINE CIRCUIT ..........................68
Diagnosis Procedure ...............................................68
ABS BRANCH LINE CIRCUIT ..........................69
Diagnosis Procedure ...............................................69
TCM BRANCH LINE CIRCUIT ..........................70
Diagnosis Procedure ...............................................70
IPDM-E BRANCH LINE CIRCUIT .....................71
Diagnosis Procedure ...............................................71
CAN COMMUNICATION CIRCUIT ...................72
Diagnosis Procedure ...............................................72
CAN SYSTEM (TYPE 6)
COMPONENT DIAGNOSIS .......................
74
MAIN LINE BETWEEN ADP AND M&A CIR-
CUIT ...................................................................
74
Diagnosis Procedure ...............................................74
MAIN LINE BETWEEN M&A AND DLC CIR-
CUIT ...................................................................
75
Diagnosis Procedure ...............................................75
Page 3070 of 5121

LAN
LAN-3
C
D
E
F
G
H
I
J
K
L B A
O
P N
MAIN LINE BETWEEN DLC AND ABS CIR-
CUIT ....................................................................
76
Diagnosis Procedure ...............................................76
ECM BRANCH LINE CIRCUIT ...........................77
Diagnosis Procedure ...............................................77
ADP BRANCH LINE CIRCUIT ...........................78
Diagnosis Procedure ...............................................78
AV BRANCH LINE CIRCUIT ..............................79
Diagnosis Procedure ...............................................79
HVAC BRANCH LINE CIRCUIT ........................80
Diagnosis Procedure ...............................................80
M&A BRANCH LINE CIRCUIT ..........................81
Diagnosis Procedure ...............................................81
STRG BRANCH LINE CIRCUIT .........................82
Diagnosis Procedure ...............................................82
BCM BRANCH LINE CIRCUIT ..........................83
Diagnosis Procedure ...............................................83
DLC BRANCH LINE CIRCUIT ...........................84
Diagnosis Procedure ...............................................84
ABS BRANCH LINE CIRCUIT ...........................85
Diagnosis Procedure ...............................................85
TCM BRANCH LINE CIRCUIT ...........................86
Diagnosis Procedure ...............................................86
IPDM-E BRANCH LINE CIRCUIT ......................87
Diagnosis Procedure ...............................................87
CAN COMMUNICATION CIRCUIT ....................88
Diagnosis Procedure ...............................................88
CAN SYSTEM (TYPE 9)
COMPONENT DIAGNOSIS .........................
90
MAIN LINE BETWEEN ADP AND M&A CIR-
CUIT ....................................................................
90
Diagnosis Procedure ...............................................90
MAIN LINE BETWEEN M&A AND DLC CIR-
CUIT ..................................................................
91
Diagnosis Procedure ...............................................91
MAIN LINE BETWEEN DLC AND ABS CIR-
CUIT ..................................................................
92
Diagnosis Procedure ...............................................92
ECM BRANCH LINE CIRCUIT .........................93
Diagnosis Procedure ...............................................93
ADP BRANCH LINE CIRCUIT ..........................94
Diagnosis Procedure ...............................................94
AV BRANCH LINE CIRCUIT ............................95
Diagnosis Procedure ...............................................95
HVAC BRANCH LINE CIRCUIT .......................96
Diagnosis Procedure ...............................................96
M&A BRANCH LINE CIRCUIT .........................97
Diagnosis Procedure ...............................................97
STRG BRANCH LINE CIRCUIT .......................98
Diagnosis Procedure ...............................................98
BCM BRANCH LINE CIRCUIT .........................99
Diagnosis Procedure ...............................................99
DLC BRANCH LINE CIRCUIT ........................100
Diagnosis Procedure .............................................100
ABS BRANCH LINE CIRCUIT ........................101
Diagnosis Procedure .............................................101
TCM BRANCH LINE CIRCUIT ........................102
Diagnosis Procedure .............................................102
IPDM-E BRANCH LINE CIRCUIT ...................103
Diagnosis Procedure .............................................103
CAN COMMUNICATION CIRCUIT .................104
Diagnosis Procedure .............................................104
Page 3071 of 5121
LAN-4
< PRECAUTION >[CAN FUNDAMENTAL]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precautions for Trouble DiagnosisINFOID:0000000003767663
CAUTION:
• Never apply 7.0 V or more to the measurement terminal.
Use a tester with open terminal voltage of 7.0 V or less.
Turn the ignition switch OFF and disconnect the battery cable from the negative terminal when
checking the harness.
Precautions for Harness RepairINFOID:0000000003767664
• Solder the repaired area and wrap tape around the soldered area.
NOTE:
A fray of twisted lines must be within 110 mm (4.33 in).
Bypass connection is never allowed at the repaired area.
NOTE:
Bypass connection may cause CAN communication error. The
spliced wire becomes separated and the characteristics of twisted
line are lost.
Replace the applicable harness as an assembly if error is detected on the shield lines of CAN communica-
tion line.
SKIB8766E
SKIB8767E
Page 3072 of 5121
![NISSAN TEANA 2008 Service Manual LAN
CAN COMMUNICATION SYSTEM
LAN-5
< FUNCTION DIAGNOSIS >[CAN FUNDAMENTAL]
C
D
E
F
G
H
I
J
K
L B A
O
P N
FUNCTION DIAGNOSIS
CAN COMMUNICATION SYSTEM
System DescriptionINFOID:0000000003767665
CAN com NISSAN TEANA 2008 Service Manual LAN
CAN COMMUNICATION SYSTEM
LAN-5
< FUNCTION DIAGNOSIS >[CAN FUNDAMENTAL]
C
D
E
F
G
H
I
J
K
L B A
O
P N
FUNCTION DIAGNOSIS
CAN COMMUNICATION SYSTEM
System DescriptionINFOID:0000000003767665
CAN com](/manual-img/5/57391/w960_57391-3071.png)
LAN
CAN COMMUNICATION SYSTEM
LAN-5
< FUNCTION DIAGNOSIS >[CAN FUNDAMENTAL]
C
D
E
F
G
H
I
J
K
L B A
O
P N
FUNCTION DIAGNOSIS
CAN COMMUNICATION SYSTEM
System DescriptionINFOID:0000000003767665
CAN communication is a multiplex communication system. This enables the system to transmit and receive
large quantities of data at high speed by connecting control units with two communication lines (CAN-H and
CAN-L).
Control units on the CAN network transmit signals using the CAN communication control circuit. They
receive only necessary signals from other control units to operate various functions.
CAN communication lines adopt twisted-pair line style (two lines twisted) for noise immunity.
System DiagramINFOID:0000000003767666
Each control unit passes an electric current to the termination circuits when transmitting CAN communication
signal. The termination circuits produce an electrical potential difference between CAN-H and CAN-L. CAN
communication system transmits and receives CAN communication signals by the potential difference.
SKIB8887E
Component Description
Main line CAN communication line between splices
Branch line CAN communication line between splice and a control unit
Splice A point connecting a branch line with a main line
Termination circuit Refer to LAN-6, "
CAN Communication Control Circuit".