Page 2809 of 4731
EI-20
REAR BUMPER
Revision: 2005 July 2005 FX
3. Remove rear reflex reflector assembly screw and remove rear
reflex reflector assembly.
Assembly
Assemble in the reverse order of disassembly.
REMOVAL AND INSTALLATION OF REAR BUMPER CLOSING
Removal
Remove clips of bumper closing and remove rear bumper closing.
Installation
Install in the reverse order of removal.
REMOVAL AND INSTALLATION OF DRAFTER GUARD
Removal
Remove clips and bolt of drafter guard and remove drafter guard.
Installation
Install in the reverse order of removal.
PIIA6417E
PIIA4954E
PIIA4955E
Page 2810 of 4731
REAR BUMPER EI-21
C
D E
F
G H
J
K L
M A
B
EI
Revision: 2005 July 2005 FX
REMOVAL AND INSTALLATION OF REAR FILLET MOLDING ASSEMBLY
Removal
1. Remove bolts of fillet molding assembly.
2. Remove clips of fillet molding assembly.
3. Remove fillet molding assembly.
Installation
1. Clean adhesive portion of rear fender with white gasoline.
2. Strip pattern from the new double adhesive tape and paste on rear fender.
3. Fillet molding assembly hold with rear fender.
PIIA4347E
Page 2811 of 4731
EI-22
FRONT GRILLE
Revision: 2005 July 2005 FX
FRONT GRILLEPFP:62310
Removal and InstallationAIS0037B
CAUTION:
Apply protection tape around outer circumference of front grille (bumper fascia side).
REMOVAL
1. Remove turn fastener of grille.
2. Remove clips on upper side of grille.
3. Pull out grille pawls, and remove grille assembly.
INSTALLATION
Install in the reverse order of removal.
1. Front grille 2. Turn fastener (CG101) 3. Clip (C205)
4. Front bumper fascia
PIIA4349E
Page 2812 of 4731

COWL TOP EI-23
C
D E
F
G H
J
K L
M A
B
EI
Revision: 2005 July 2005 FX
COWL TOPPFP:66100
Removal and InstallationAIS0037C
REMOVAL
1. Remove clips of hood ledge cover and remove hood ledge cover.
2. Remove wiper arms (RH/LH). Refer to WW-32, "
Removal and Installation of Front Wiper Arms, Adjust-
ment of Wiper Arms Stop Location" .
3. Remove cowl top seal rubber.
4. Remove clips of cowl top cover (RH) and remove cowl top cover (RH).
5. Remove clips, cap and bolts and remove cowl top cover (LH).
6. Remove washer hose from cowl top cover.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When installing cowl top cover, make sure that blind clips are securely fitted in panel holes on
body, and then press them in.
After installing, perform adjustment of wiper arms. Refer to WW-32, "Removal and Installation of
Front Wiper Arms, Adjustment of Wiper Arms Stop Location" .
1. Cowl top cover (RH) 2. Clip (C205) 3. Hood ledge cover (RH)
4. Cowl top seal rubber 5. Hood ledge cover (LH) 6. Bolt
7. Cap 8. Cowl top cover (LH)
PIIA4946E
Page 2813 of 4731
EI-24
FENDER PROTECTOR
Revision: 2005 July 2005 FX
FENDER PROTECTORPFP:63840
Removal and InstallationAIS0037D
REMOVAL
1. Remove bolts of fender protector front.
2. Remove clips of fender protector front.
3. Remove fender protector front.
4. Remove bolt of fender protector rear.
5. Remove clips of fender protector rear.
6. Remove fender protector rear.
INSTALLATION
Install in the reverse order of removal.
PIIA4326E
1. Fender protector front 2. Clip (C103) 3. Screw
4. Bolt 5. Fender protector rear 6. Clip
Page 2814 of 4731
DOOR OUTSIDE MOLDING EI-25
C
D E
F
G H
J
K L
M A
B
EI
Revision: 2005 July 2005 FX
DOOR OUTSIDE MOLDING PFP:82820
Removal and InstallationAIS0037E
FRONT DOOR OUTSIDE MOLDING
Removal
1. Open windows fully.
2. Remove door mirror. Refer to GW-114, "
Removal and Installation" .
3. Disconnect pawl on rear edge of molding.
4. Lift up to upper side, and remove molding.
Installation
Install in the reverse order of removal.
REAR DOOR OUTSIDE MOLDING
Removal
1. Open windows fully.
2. Disconnect pawl on front edge and rear edge of molding.
3. Lift up to upper side, and remove molding.
Installation
Install in the reverse order of removal.
CAUTION:
Be careful not to apply excessive force when removing because it is easy deform parts.
After removal, visually inspect molding, and it is deformed, replace it with new molding.
1. Rear door outside molding 2. Rear door panel 3. Front door panel
4. Front door outside molding
PIIA4949E
Page 2815 of 4731
EI-26
DOOR OUTSIDE LOWER MOLDING
Revision: 2005 July 2005 FX
DOOR OUTSIDE LOWER MOLDINGPFP:82877
Removal and InstallationAIS0037F
FRONT AND REAR DOOR OUTSIDE LOWER MOLDING
Removal
Remove clips, then remove door outside lower molding with double-faced adhesive tape.
Installation
1. Clean adhesive portion of front and rear door with white gasoline.
2. Strip pattern from the new door outside lower molding and paste on door.
CAUTION:
Do not let air between contact surfaces when installing.
To secure contact, do not wash vehicle within 24 hours after installation.
1. Rear door outside lower molding 2. Front door outside lower molding 3. Clip (with lower molding)
4. Grommet 5. Door panel 6. Double-faced adhesive tape
PIIA4348E
Page 2816 of 4731
DOOR PARTING SEAL EI-27
C
D E
F
G H
J
K L
M A
B
EI
Revision: 2005 July 2005 FX
DOOR PARTING SEALPFP:80838
Removal and InstallationAIS0037G
REMOVAL
1. Remove rear door outside lower molding. Refer to EI-26, "Removal and Installation" .
2. Open front door fully.
3. Remove double-faced adhesive tapes and rear door parting seal.
INSTALLATION
1. Clean adhesive portion of rear door with white gasoline.
2. Strip pattern from the new rear door parting seal and paste on rear door panel.
3. Install rear door parting seal to rear door hem flange.
4. Install rear door outside lower molding. Refer to EI-26, "
Removal and Installation" .
CAUTION:
Rear door parting seal is not reusable. always use new rear door parting seal.
PIIA4950E
1. Rear door parting seal rubber 2. Rear door panel 3. Rear door outside lower molding