Page 809 of 4731
BCS-10
BCM (BODY CONTROL MODULE)
Revision: 2005 July 2005 FX
CAN Communication UnitAKS00AOE
Refer to LAN-30, "CAN Communication Unit" .
Vehicle-speed-sensing intermittent wiperCombination switch
Combination meter IPDM E/R
Rear intermittent wiper Combination switch Rear wiper motor
Rear window defogger
Rear window defogger switch
Ignition switch IPDM E/R
A/C switch signal Unified meter and A/C amp. ECM
Blower fan switch signal Unified meter and A/C amp. ECM
Low tire pressure warning system Remote keyless entry receiver Combination meter System Input Output
Page 810 of 4731
BCM (BODY CONTROL MODULE) BCS-11
C
D E
F
G H
I
J
L
M A
B
BCS
Revision: 2005 July 2005 FX
SchematicAKS0058A
TKWM2093E
Page 811 of 4731
BCS-12
BCM (BODY CONTROL MODULE)
Revision: 2005 July 2005 FX
TKWM2094E
Page 812 of 4731

BCM (BODY CONTROL MODULE) BCS-13
C
D E
F
G H
I
J
L
M A
B
BCS
Revision: 2005 July 2005 FX
CONSULT-II Function (BCM)AKS0058B
CONSULT-II can display each diagnostic item using the diagnostic test mode shown following.
CONSULT–II INSPECTION PROCEDURE
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
1. With the ignition switch OFF, connect CONSULT-II and CON- SULT-II CONVERTER to the data link connector, then turn the
ignition switch ON.
2. Touch “START (NISSAN BASED VHCL)”.
3. Touch “BCM” on “SELECT SYSTEM” screen. If “BCM” is not indicated, refer to GI-39, "
CONSULT-II Data Link
Connector (DLC) Circuit" .
BCM diagnostic test item Check item, diagnostic test mode Content
Inspection by part WORK SUPPORT Changes setting of each function.
SELF-DIAG RESULTS BCM performs self-diagnosis of CAN communication.
DATA MONITOR Displays the input data of BCM in real time.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN com-
munication can be read.
ACTIVE TEST Gives a drive signal to a load to check the operation.
ECU PART NUMBER ECM part number can be read.
CONFIGURATION (Not be used)
PBIB1503E
BCIA0029E
BCIA0030E
Page 813 of 4731

BCS-14
BCM (BODY CONTROL MODULE)
Revision: 2005 July 2005 FX
4. Select the desired part to be diagnosed on the “SELECT TEST
ITEM” screen.
ITEMS OF EACH PART
NOTE:
CONSULT-II displays systems equipped in the vehicle.
× :Applicable
NOTE:
*1: This item is displayed, but should not be used.
*2: This item is displayed, but does not function.
PKIA5226E
System and item CONSULT-II display Diagnostic test mode (Inspection by part)
WORK
SUPPORT SELF
−
DIAG
RESULTS DATA
MONI-
TOR CAN
DIAG SUP-
PORT
MNTR ACTIVE
TEST ECU
PA R T
NUM- BER CON-
FIGU-
RATION
BCM BCM ×× × ×
×
*1
Power door lock system DOOR LOCK ×××
Rear window defogger REAR DEFOGGER ××
Warning chime BUZZER ××
Room lamp timer INT LAMP ×××
Headlamp HEAD LAMP ×××
Wiper WIPER ×××
Turn signal lamp
Hazard lamp FLASHER
××
Blower fan switch signal
A/C switch signal AIR CONDITONER
×
Intelligent Key system INTELLIGENT KEY ×
Combination switch COMB SW ×
IVIS IMMU ××
Room lamp battery saver BATTERY SAVER ×× ×
Trunk lid TRUNK
*2××
Vehicle security system THEFT ALM ×××
Retained power control RETAINED PWR ×××
Oil pressure switch SIGNAL BUFFER ××
Low tire pressure warning
system AIR PRESSURE
MONITOR ×××
Panic system PANIC ALARM ×
Page 814 of 4731

BCM (BODY CONTROL MODULE) BCS-15
C
D E
F
G H
I
J
L
M A
B
BCS
Revision: 2005 July 2005 FX
WORK SUPPORT
Operation Procedure
1. Touch “BCM” on “SELECT TEST ITEM” screen.
2. Touch “WORK SUPPORT” on “SELECT DIAG MODE” screen.
3. Touch item on “SELECT WORK ITEM” screen.
4. Touch “START”.
5. Touch “CHANGE SET”.
6. The setting will be changed and “RESETTING COMPLETED” will be displayed.
7. Touch “END”.
Display Item List
CAN Communication Inspection Using CONSULT-II (Self-Diagnosis)AKS0058C
1. CHECK SELF-DIAGNOSTIC RESULT
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
1. Connect to CONSULT-II, and select “BCM” on “SELECT SYSTEM” screen.
2. Select “BCM control unit ” on “SELECT WORK ITEM” screen, and select “SELF-DIAG RESULTS”.
3. Check display content in self-diagnostic results.
Contents displayed
No malfunction>>INSPECTION END
Malfunction in CAN communication system>>After printing the monitor items, go to “CAN System”. Refer to LAN-5, "
Precautions When Using CONSULT-II" .
Item Description
RESET SETTING VALUE Return a value set with WORK SUPPORT of each system to a default value in factory shipment.
CONSULT-II display code Diagnosis item
U1000 INITIAL DIAG
TRANSMIT DIAG ECM
IPDM E/R
METER/M&A I-KEY
Page 815 of 4731
BCS-16
BCM (BODY CONTROL MODULE)
Revision: 2005 July 2005 FX
Removal and Installation of BCMAKS0058E
REMOVAL
1. Remove the dash side finisher (LH). Refer to EI-36, "BODY
SIDE TRIM" in “EI Exterior/Interior.”
2. Disconnect BCM connector.
3. Remove bracket mounting screws (3) to remove BCM and fuse block with bracket.
4. Raise the pawl of fuse block and remove bracket from fuse block to remove BCM.
INSTALLATION
Installation is the reverse order of removal.
NOTE:
When replacing BCM perform initialization of NATS system and registration of all NATS ignition key IDs.
SKIA4964E
SKIA4965E
Page 816 of 4731

BL-1
BODY, LOCK & SECURITY SYSTEM
I BODY
CONTENTS
C
D E
F
G H
J
K L
M
SECTION BL
A
B
BL
Revision: 2005 July 2005 FX
BODY, LOCK & SECURITY SYSTEM
PRECAUTIONS .......................................................... 5
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 5
Precautions Necessary for Steering Wheel Rotation
After Battery Disconnect ..................................... ..... 5
OPERATION PROCEDURE ............................ ..... 5
Precautions for Work ........................................... ..... 5
PREPARATION ...................................................... ..... 6
Special Service Tools .......................................... ..... 6
Commercial Service Tools ................................... ..... 6
SQUEAK AND RATTLE TROUBLE DIAGNOSIS . ..... 7
Work Flow ........................................................... ..... 7
CUSTOMER INTERVIEW ................................ ..... 7
DUPLICATE THE NOISE AND TEST DRIVE .. ..... 8
CHECK RELATED SERVICE BULLETINS ...... ..... 8
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ................................................. ..... 8
REPAIR THE CAUSE ...................................... ..... 8
CONFIRM THE REPAIR .................................. ..... 9
Generic Squeak and Rattle Troubleshooting ...... ..... 9
INSTRUMENT PANEL ..................................... ..... 9
CENTER CONSOLE ........................................ ..... 9
DOORS ............................................................ ..... 9
TRUNK ............................................................. ... 10
SUNROOF/HEADLINING ................................ ... 10
SEATS .............................................................. ... 10
UNDERHOOD .................................................. ... 10
Diagnostic Worksheet ......................................... .... 11
HOOD .................................................................... ... 13
Fitting Adjustment ............................................... ... 13
LONGITUDINAL AND LATERAL CLEARANCE
ADJUSTMENT ................................................. ... 13
FRONT END HEIGHT ADJUSTMENT ............ ... 13
SURFACE HEIGHT ADJUSTMENT ................ ... 13
Removal and Installation of Hood Assembly ....... ... 14
REMOVAL ........................................................ ... 15
INSTALLATION ................................................ ... 15
Removal and Installation of Hood Lock Control .. ... 15
REMOVAL ........................................................ ... 15 INSTALLATION ................................................
... 16
Hood Lock Control Inspection ............................. ... 16
RADIATOR CORE SUPPORT ............................... ... 18
Removal and Installation ..................................... ... 18
REMOVAL ........................................................ ... 18
INSTALLATION ................................................ ... 19
FRONT FENDER ................................................... ... 20
Removal and Installation ..................................... ... 20
REMOVAL ........................................................ ... 20
INSTALLATION ................................................ ... 20
POWER DOOR LOCK SYSTEM ........................... ... 21
Component Parts and Harness Connector Location ... 21
Component Parts and Harness Connector Location ... 22
System Description .............................................. ... 22
OUTLINE .......................................................... ... 23
CAN Communication System Description ........... ... 24
CAN Communication Unit .................................... ... 24
Schematic/With Intelligent Key ............................ ... 25
Wiring Diagram -D/LOCK-/With Intelligent Key ... ... 26
FIG. 1 ................................................................ ... 26
FIG. 2 ................................................................ ... 27
FIG. 3 ................................................................ ... 28
FIG. 4 ................................................................ ... 29
FIG. 5 ................................................................ ... 30
Schematic/Without Intelligent Key ....................... ... 31
Wiring Diagram -D/LOCK-/Without Intelligent Key ... 32
FIG. 6 ................................................................ ... 32
FIG. 7 ................................................................ ... 33
FIG. 8 ................................................................ ... 34
FIG. 9 ................................................................ ... 35
Terminals and Reference Value for BCM ............ ... 36
Terminals and Reference Value for Intelligent Key
Unit (With Intelligent Key System) ....................... ... 36
Work Flow ............................................................ ... 36
CONSULT-II Function (BCM) .............................. ... 37
CONSULT-II INSPECTION PROCEDURE ....... ... 37
CONSULT-II APPLICATION ITEMS ................. ... 38
Trouble Diagnosis Chart by Symptom ................. ... 40
Check BCM Power Supply and Ground Circuit ... ... 41
Check Door Switch .............................................. ... 42