Page 25 of 4731
![INFINITI FX35 2005 Service Manual ACS-16
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: 2005 July 2005 FX
The area is not suitable for the adjustment work.
ICC sensor is not clean.
8. After the CONSULT-II displays “ADJUST THE VERTI INFINITI FX35 2005 Service Manual ACS-16
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: 2005 July 2005 FX
The area is not suitable for the adjustment work.
ICC sensor is not clean.
8. After the CONSULT-II displays “ADJUST THE VERTI](/manual-img/42/57020/w960_57020-24.png)
ACS-16
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: 2005 July 2005 FX
The area is not suitable for the adjustment work.
ICC sensor is not clean.
8. After the CONSULT-II displays “ADJUST THE VERTICAL OF LASER BEAM AIMING” turn the up-down direction adjusting
screw until “U/D CORRECT” value is set in the range of ±4.
CAUTION:
Turn the screw slowly. The value change on display is
slower than actual movement of the ICC sensor. Wait for 2
seconds every time the screw is turned half a rotation.
NOTE:
Turning the screw to the right lowers the aiming and to the left
lifts the aiming.
9. When “U/D CORRECT” value indicates ±4, confirm that the margin of value remains within ±4 at least for
2 seconds with no equipment or hand touching the ICC sensor.
When “COMPLETED THE VERTICAL AIMING OF LASER
BEAM” appears on screen, touch “END”.
CAUTION:
Be sure that the margin of “U/D CORRECT” is within ±4 with
ICC sensor unit is untouched.
10. Confirm that “ADJUSTING AUTOMATIC HORIZONTAL LASER BEAM AIMING” is on screen and wait for a while (maximum: 10
seconds).
SKIA1221E
SKIA6181E
SKIA1223E
SKIA1224E
Page 26 of 4731
LASER BEAM AIMING ADJUSTMENT ACS-17
[ICC]
C
D E
F
G H
I
J
L
M A
B
ACS
Revision: 2005 July 2005 FX
11. Confirm that “NORMALLY COMPLETED” is displayed on CON-
SULT-II and close the aiming adjustment procedure by touching
“END”.
CAUTION:
Complete all the procedures once “LASER BEAM ADJUST”
mode is entered in CONSULT-II. When the procedure is dis-
continued, the ICC system is inoperable.
CHECK AFTER THE ADJUSTMENT
Test the ICC system operation by running test. Refer to ACS-9, "ICC System Running Test" .
SKIA1225E
Page 27 of 4731
ACS-18
[ICC]
ELECTRICAL UNITS LOCATION
Revision: 2005 July 2005 FX
ELECTRICAL UNITS LOCATIONPFP:25230
Component Parts and Harness Connector LocationAKS006YN
PKIB4162E
Page 28 of 4731
WIRING DIAGRAM ACS-19
[ICC]
C
D E
F
G H
I
J
L
M A
B
ACS
Revision: 2005 July 2005 FX
WIRING DIAGRAMPFP:00000
SchematicAKS006YO
TKWM2067E
Page 29 of 4731
ACS-20
[ICC]
WIRING DIAGRAM
Revision: 2005 July 2005 FX
Wiring Diagram — ICC —AKS007WA
TKWM0648E
Page 30 of 4731
WIRING DIAGRAM ACS-21
[ICC]
C
D E
F
G H
I
J
L
M A
B
ACS
Revision: 2005 July 2005 FX
TKWM1090E
Page 31 of 4731
ACS-22
[ICC]
WIRING DIAGRAM
Revision: 2005 July 2005 FX
TKWM2068E
Page 32 of 4731
WIRING DIAGRAM ACS-23
[ICC]
C
D E
F
G H
I
J
L
M A
B
ACS
Revision: 2005 July 2005 FX
TKWM0651E