Page 2825 of 4731
EI-36
BODY SIDE TRIM
Revision: 2005 July 2005 FX
BODY SIDE TRIMPFP:76913
Removal and InstallationAIS0037N
CAUTION:
Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
CENTER PILLAR LOWER GARNISH
Removal
1. Remove front and rear kicking plate.
2. Remove front and rear body side welt.
1. Front pillar garnish 2. Front body side welt 3. Dash side finisher
4. Nut 5. Front kicking plate 6. Center pillar lower garnish
7. Center pillar upper garnish 8. Bolt 9. Center pillar upper cap
10. Rear body side welt 11. Rear kicking plate 12. Clip (C203)
13. Center mudguard finisher (rear) 14. Center mudguard finisher (front)
PIIA4340E
PIIA4344E
Page 2826 of 4731

BODY SIDE TRIM EI-37
C
D E
F
G H
J
K L
M A
B
EI
Revision: 2005 July 2005 FX
3. Remove center pillar lower garnish.
NOTE:
Insert screwdriver rolled with cloth between panel on vehicle and
clips, then disconnect clips.
Installation
Install in the reverse order of removal.
NOTE:
To install, check if all clips are matched over holes of panel on vehicle, then push on.
CENTER PILLAR UPPER GARNISH
Removal
1. Remove seat belt shoulder anchor. Refer to SB-3, "Removal and Installation of Front Seat Belt" .
2. Remove front and rear kicking plate.
3. Remove front and rear body side welt.
4. Remove center pillar lower garnish.
5. Remove center pillar upper cap and bolt.
6. Remove center pillar upper garnish.
Installation
Install in the reverse order of removal.
DASH SIDE FINISHER
Removal
1. Remove front kicking plate.
2. Remove front body side welt.
3. Remove nut.
4. Remove dash side finisher.
NOTE:
Insert screwdriver rolled with cloth between panel on vehicle and
clips, then disconnect clips.
Installation
Install in the reverse order of removal.
NOTE:
To install, check if all clips are matched over holes of panel on vehicle, then push on.
PIIA4341E
PIIA4342E
PIIA4343E
Page 2827 of 4731
EI-38
BODY SIDE TRIM
Revision: 2005 July 2005 FX
FRONT PILLAR GARNISH
Removal
Remove front pillar garnish clips and remove front pillar garnish.
Installation
Install in the reverse order of removal.
KICKING PLATE
Removal
Remove kicking plate clips and remove kicking plate.
Installation
Install in the reverse order of removal.
CENTER MUDGUARD FINISHER (FRONT/REAR)
Removal
1. Remove center mudguard finisher (front).
2. Remove center mudguard finisher clip and remove center mud- guard finisher (rear).
Installation
Install in the reverse order of removal.
PIIA4345E
PIIA4346E
Page 2828 of 4731

FLOOR TRIM EI-39
C
D E
F
G H
J
K L
M A
B
EI
Revision: 2005 July 2005 FX
FLOOR TRIMPFP:74902
Removal and InstallationAIS0037O
REMOVAL
1. Remove front seat and rear seat cushion. Refer to SE-100, "Removal and Installation" and SE-106,
"Removal and Installation" .
2. Remove center console assembly. Refer to IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
3. Remove front and rear kicking plate. Refer to EI-36, "
Removal and Installation" .
4. Remove front and rear body side welt. Refer to EI-36, "
Removal and Installation" .
5. Remove center pillar lower garnish. Refer to EI-36, "
Removal and Installation" .
6. Remove footrest screw, cover and foot-rest.
7. Remove dash side finisher. Refer to EI-36, "
Removal and Instal-
lation" .
8. Remove foot-grille (RH/LH).
9. Remove NAVI control unit. Refer to AV- 1 8 0 , "
Removal and
Installation of NAVI Control Unit" .
10. Remove carpet hook.
PIIA4956E
1. Floor carpet 2. Carpet hook 3. Nut
4. Foot-grille (RH) 5. Foot-grille (LH) 6. Foot-rest (driver)
7. Fixing clip 8. NAVI control unit
PIIA4957E
Page 2829 of 4731
EI-40
FLOOR TRIM
Revision: 2005 July 2005 FX
11. Remove floor carpet from carpet fixing clip and remove floor car-
pet.
INSTALLATION
Install in the reverse order of removal.
PIIA1223E
Page 2830 of 4731
HEADLINING EI-41
C
D E
F
G H
J
K L
M A
B
EI
Revision: 2005 July 2005 FX
HEADLININGPFP:73910
Removal and InstallationAIS0037P
PIIB3263E
Page 2831 of 4731

EI-42
HEADLINING
Revision: 2005 July 2005 FX
REMOVAL
1. Remove front pillar garnish. Refer to EI-36, "Removal and Installation" .
2. Remove kicking plate (front/rear). Refer to EI-36, "
Removal and Installation" .
3. Remove body side welt. Refer to EI-36, "
Removal and Installation" .
4. Remove seat belt shoulder anchor (front/rear). Refer to SB-3, "
Removal and Installation of Front Seat
Belt" and SB-5, "Removal and Installation of Rear Seat Belt" .
5. Remove center pillar garnish (lower/upper) and luggage side finisher assembly and rear pillar upper gar- nish assembly. Refer to EI-36, "
Removal and Installation" and EI-43, "Removal and Installation" .
6. Remove assist grip caps and screw. Remove assist grip.
7. Remove sun-visor (RH/LH), and disconnect harness connector with lamp model.
8. Remove sun-visor holder.
9. Remove DVD display rear. Refer to AV- 1 9 8 , "
Removal and Installation for DVD Display Unit" .
10. Remove roof console.
11. Remove LDW camera unit. Refer to D I - 111 , "
Removal and Installation for LDW Camera Unit" .
12. Disconnect harness connector at front left side of headlining.
13. Put front seat to front most and recline seat back to backward.
14. Remove headlining, turn and take out from back door. CAUTION:
Always remove or install in a pair.
Cover surroundings with waste to avoid scratches or damages.
Do not bend headlining too hard.
15. Remove following parts after removing headlining.
Room lamp
Personal lamp
INSTALLATION
Install in the reverse order of removal.
1. Headlining 2. Assist grip (rear) 3. Assist grip (front)
4. Sun-visor holder (RH) 5. Sun-visor (RH) 6. Sun-visor cover (RH)
7. Roof console (without LDW camera unit) 8. Sun-visor (LH) 9. Sun-visor cover (LH)
10. Sun-visor holder (LH) 11. Finisher 12. Room lamp
13. Personal lamp 14. Fastener 15. DVD display rear
16. Roof console (with LDW cam- era unit)
PIIA4952E
Page 2832 of 4731
LUGGAGE FLOOR TRIM EI-43
C
D E
F
G H
J
K L
M A
B
EI
Revision: 2005 July 2005 FX
LUGGAGE FLOOR TRIMPFP:84999
Removal and InstallationAIS0037Q
PIIB2429E