2005 INFINITI FX35 reset

ACS-6
[ICC]
DESCRIPTION
Revision: 2005 July 2005 FX
DESCRIPTIONPFP:00000
OutlineAKS00C8B
The Intelligent Cruise Control (ICC) system automatically maintains a selected distance from the vehicle
ahead according to that vehicle's speed, or at the set speed, if the road ahead is clear.
The ICC function has two cruise control modes and brake assist (with preview function).
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE
Vehicle-to-vehicle distance control mode, the driver can maintain the same speed as other vehicles without
the constant need to adjust the set speed as you would with a normal cruise control system.
The system is intended to enhance the operation of the vehicle when following the vehicle traveling in the
same lane and direction.
If the distance sensor detects a slower moving vehicle ahead, the system will reduce speed so that the vehicle
ahead can be followed at the selected distance.
The system automatically controls the throttle and applies the brakes (up to 25% of vehicle braking power) if
necessary.
The detection range of the sensor is approximately 390 ft (120 m) ahead.
Refer to Owner's Manual for Intelligent Cruise Control System operating instructions.
CONVENTIONAL (FIXED SPEED) CRUISE CONTROL MODE
Conventional (fixed speed) cruise control mode is cruising at preset speeds.
Refer to Owner's Manual for Intelligent Cruise Control System operating instructions.
BRAKE ASSIST (WITH PREVIEW FUNCTION)
When the force applied to brake pedal exceeds a certain level, the Brake Assist is activated and generates a
greater braking force than that of a conventional brake booster even with light pedal force.
When the Preview Function identifies the need to apply the sudden brake by sensing the vehicle ahead in the
same lane and the distance and relative speed from it, it applies the brake pre-pressure before driver depress
the brake pedal and improves brake response by reducing its free play.
Refer to Owner's Manual for BRAKE ASSIST (WITH PREVIEW FUNCTION) operating instructions.
System DiagramAKS00C8C
PKIB4142E

AV-58
INTEGRATED DISPLAY SYSTEM
Revision: 2005 July 2005 FX
DRIVE COMPUTER
Refer to Owner′s Manual for drive computer operating instructions.
TRIP Switch
When “TRIP” switch is pressed, display TRIP screen. As TRIP infor-
mation, it indicates journey time (TIME), trip odometer (DIST), aver-
age vehicle speed (AVG).
Pressing “TRIP” switch once cycles display from TRIP 1 →TRIP
2 → Display OFF →TRIP 1.
“TIME”

Journey time indication is performed by reset or battery connec-
tion.

When pushing “TRIP RESET” or “TRIP” switch more than
approximately 1.5 seconds, journey time will be reset.

If journey time is reset, journey distance and average speed will
be reset at the same time.
“DIST”

Trip odometer indication is performed by vehicle speed signal.

When pushing “TRIP RESET” or “TRIP” switch more than approximately 1.5 seconds, driving distance will
be reset.

If trip odometer is reset, journey time and average speed will be reset at the same time.
“AVG”

Average speed indication is performed by running distance and running time.

Indication will be renewed every 30 seconds.

When pushing “TRIP RESET” or “TRIP” switch more than approximately 1.5 seconds, average speed will
be reset.

After reset operation, the displays shows “ ” for 30 seconds.
FUEL ECON Switch
When “FUEL ECON” switch is pressed, display FUEL ECON screen.
As FUEL ECON information, it indicates average fuel consumption
(AVG), distance to empty (DTE).
Pressing “FUEL ECON” switch once cycles display from FUEL
ECON →Display OFF →FUEL ECON.
“AVG” (Average Fuel Consumption)

Average fuel consumption indication is performed by fuel con-
sumption signal and vehicle speed signal after system is reset.

Indication will be renewed every 30 seconds.

When pushing “TRIP RESET” or “FUEL ECON” switch more
than approximately 1.5 seconds, average fuel economy will be
reset.

After reset operation, the display shows “ . ” until the vehicle is driven 500 m (1,600 ft.) or 30 seconds
has passed.
“DTE” (Distance to Empty)

Distance to empty receives via CAN communication and indicates values calculated by meter.

Display range is max 999 miles (max 999 km).

If low-fuel WARNING is received from meter via CAN communication, distance to empty indication will be
“”.

Indication will be renewed every 30 seconds.
SKIA5916E
SKIA5917E

INTEGRATED DISPLAY SYSTEM AV-59
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
MAINT Switch (Maintenance Switch)

When “MAINT” switch is pressed, display vehicle information screen. As vehicle information, it indicates
engine oil, tire rotation, tire pressure.

Pressing “MAINT” switch once cycles display from engine oil →tire rotation →tire pressure →display
OFF →engine oil.
Engine Oil and Tire Rotation

Operating the joystick left/right, replace distance can be set.

When journey distance is the same as replace distance, alert is
displayed. (SERVICE ALERT setting is ON.)

Selected replace distance is 0 - 7,500 miles (0 - 12,000 km) in
increments of 500 mile (800 km).

Press and hold “TRIP RESET or MAINT” switch for 1.5 seconds
or longer, reset present journey distance.

During driving, cannot change settings.
Tire Pressure

Tire pressure signal is received from BCM through CAN commu-
nication line.

Tire pressure is displayed.

When FLAT TIRE signal is received from BCM, “FLAT TIRE” is
displayed.
E/M SWITCH
When “E/M” (English/Metric) switch is pressed, change the unit as followings.
SKIA5918E
SKIA5919E
Unit US Mile,
°F, M P G
Metric km, °C, l/100km

AV-60
INTEGRATED DISPLAY SYSTEM
Revision: 2005 July 2005 FX
SETTING SCREEN

Setting of electric status can be changed by A/C and AV switch. The signal is sent to BCM through display
unit to change vehicle electric system setting.

Display unit is communicating with driver seat control unit.

Pressing “SETTING” switch once cycles display from DISPLAY →LANGUAGE →BEEP SET →SERVICE
ALERT →PERSONALIZED SETTINGS MENU →DISPLAY OFF →DISPLAY.

Using the joystick, setting of each item will become possible.
Adjustable Vehicle Status
NOTE:
Setting in factory shipment is ON. Setting items
Setting
variations Initial
setting Operation
DISPLAY ON/OFF ON It switches displayed/Non-displayed of the screen.
LANGUAGE ENGLISH/
FRANCAIS – It switches displayed language.
BEEP SET ON/OFF ON It selects beep sound ON/OFF during switch operation. How-
ever, even if beep is set OFF, beep for NO OPERATION and
for screen interception are not reset.
SERVICE ALERT ON/OFF OFF It switches displayed/Non-displayed of alert indication.

When the setting is ON, if engine oil or tire rotation will be
replace distance, alert is displayed.

When the setting is OFF, alert is not displayed.
PERSONALIZED
SETTING MENU SLIDE BACK DR
SEAT ON EXIT ON/OFF
ON
NOTEThe driver’s seat automatically moves back and returns to the
original position for exceptional ease of exit and entry. (Models
with automatic drive positioner.)
LIFT STEERING
WHEEL ON EXIT ON/OFF
ON
NOTEThe steering column automatically tilts up and returns to the
original position for exceptional ease of entry and exit. (Models
with automatic drive positioner.)
REMOTE UNLOCK
DOOR LOGIC DR-1ST/ALL DR-1ST This key can switch the unlock doors of the 1st unlocking oper-
ation as follows:

Only the driver side door ⇔All the doors
HORN CHIRP
WITH REMOTE ON/OFF ON This key changes the horn chirp mode occurring when pressing
the LOCK button on the keyfob.
LAMPS FLASH
WITH REMOTE ALL/LOCK/
UNLOCK/OFF ALLThis key changes the hazard indicator flash mode occurring
when pressing the LOCK or UNLOCK button on the keyfob.
AUTO RE-LOCK
TIME 5m/1m/OFF 1m The length of auto door re-lock time can be set. Select the
“Auto Re-Lock timer” key, then move the joystick to adjust the
time.
AUTO HEADLAMP
SENSITIVITY LEVEL 1/2/3/4 LEVEL 2 Automatic light illumination can be set as desired. Select the
“Auto Headlamp Sensitivity” key, then move the joystick to the
left (lower) or right (higher).
AUTO HEADLAMP
OFF DELAY OFF/30/45/60/
90/120/150/ 180 SEC 45 SEC This key can control how long it takes the automatic turn off
timer to extinguish the headlamps in “AUTO” position. Select
the “Auto Headlamp Off Delay” key, then move the joystick to
the left or right to adjust the timer.
SPEED SENSING
WIPER INTERVAL ON/OFF ON This key turns on and off the driving speed dependent intermit-
tent wiper function.
CONFIRM RESET
SETTINGS YES/NO NO When this key is selected and turned on using the “ENTER”
button, all settings mode by PERSONALIZED SETTINGS will
return to the initial conditions.

AV-102
NAVIGATION SYSTEM
Revision: 2005 July 2005 FX
TRIP 1 OR TRIP 2

Elapsed Time, Driving Distance and Average Speed are dis-
played as Trip 1 information or Trip 2 information.

The way to reset is by pushing the “Reset” switch or by keeping
pushing “TRIP” button more than 1.5 seconds.
FUEL ECONOMY

Average Fuel Economy, Distance to Empty, Fuel Economy are
displayed as Fuel Economy information.

The way to reset is by pushing the “Reset” switch or by keeping
pushing “TRIP” button more than 1.5 seconds.
MAINTENANCE

Engine Oil, Tire Rotation and Tire Pressure are displayed as
Maintenance information.
ENGINE OIL OR TIRE ROTATION

Possible to set up interval of engine oil and tire rotation by mov-
ing joystick right and left.
SKIA5990E
SKIA5991E
SKIA5992E
SKIA5993E

AV-172
NAVIGATION SYSTEM
Revision: 2005 July 2005 FX
DESTINATION, PASSING POINTS, AND MENU ITEMS CANNOT BE SELECTED/SET
VOICE GUIDE
ROUTE SEARCH
Symptom Cause Remedy
Destination cannot be set. Destination to be set is on an expressway. Set the destination on an ordinary road.
Passing point is not searched
when re-searching the route. The vehicle has already passed the passing point,
or the system judged so. To include the passing points that have been
passed into the route again, set the route
again.
Route information will not be dis-
played. Route searching has not been done. Set the destination and perform route
searching.
Vehicle mark is not on the recommended route. Drive on the recommended route.
Route guide is turned OFF. Turn route guide ON.
Route information is not available on the dark pink
route. System is not malfunction.
After the route searching, no guide
sign will appear as the vehicle
goes near the entrance/exit to the
toll road. Vehicle mark is not on the recommended route.
(On the display, only guide signs related to the
recommended route will be shown.) Drive on the recommended route.
Automatic route searching is not
possible. Vehicle is driving on a highway (gray route), or no
recommended route is available. Drive on a road to be searched. Or re–
search the route manually. In this case, how-
ever, the whole route will be searched.
Performed automatic detour
search (or detour search). How-
ever, the result is the same as that
of the previous search. Performed search with every condition consid-
ered. However, the result is the same as that of
the previous search. System is not malfunction.
Passing points cannot be set. More than five passing points were set. Passing points can be set up to five. To stop at more than five points, perform sharing in
several steps.
When setting the route, the start-
ing point cannot be selected. The current vehicle location is always set as the
starting point of a route. System is not malfunction.
Some menu items cannot be
selected. The vehicle is being driven. Stop the vehicle at a safe place and then
operate the system.
Symptom Cause Remedy
Voice guide will not operate. Note: Voice guide is only available at intersections that satisfy certain conditions . Therefore, guid-
ance may not be given even when the route on the
map changes direction. System is not malfunction.
The vehicle is not on the recommended route. Return to the recommended route or re- search the route.
Voice guide is turned OFF. Turn voice guide ON.
Route guide is turned OFF. Turn route guide ON.
Voice guide does not match the
actual road pattern. Voice guide may vary with the direction to which
the vehicle is turn and the connection of the road
to other roads. Drive in conformity to the actual traffic rules.
Symptom Cause Remedy
No route is shown. No road to be searched is found around the des- tination. Find wider road (orange road or wider)
nearby and reset the destination and passing
points onto it. Take care of the traveling
direction when there are separate up and
down roads.
Starting point and the destination are too close. Set the destination at more distant point.
Conditional traffic regulation (day of the week/
time of the day) is set at the area around the cur-
rent location or the destination. Turn the time-regulating search conditions
OFF. Turn “Avoid regulation time” in the
search conditions OFF.

NAVIGATION SYSTEM AV-173
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
NOTE:
Except for the ordinance-designated cities and the prefectural capitals (Malfunctioning areas may be changed in the updated map disc.)
Indicated route is intermittent. In some areas, highways (gray routes) are not
used for the search
(Note) Therefore, the route to
the current location or the passing points may be
intermittent. System is not malfunction.
When the vehicle has passed the
recommended route, it is deleted
from the screen. A recommended route is controlled by each sec-
tion. When the vehicle has passed the passing
point 1, then the map data from the starting point
up to the passing point 1 will be deleted. (The
data may remain undeleted in some area.) System is not malfunction.
Detouring route is recommended. In some areas, highways (gray routes) are not used for the search.
(Note) Therefore, detour
route may be recommended. Set the route closer to the basic route (gray
route).
A detour route may be shown when some traffic
regulation (one-way traffic, etc.) is set at the area
around the starting point or the destination. Slightly move the starting point or the desti-
nation, or set the passing point on the route
of your choice.
In the area where highways (gray routes) are
used for the search, left turn has priority around
the current location and the destination (passing
points). For this reason, the recommended route
may be detouring. System is not malfunction.
Landmarks on the map do not
match the actual ones. This can be happen due to omission or error in
the map data. As a rule, an updated map DVD-ROM will be
released once a year. Wait until the latest
map has become available.
Recommended route is far from
the starting point, passing points,
and destination. Starting point, passing points, and destination of
the route guide were set far from the desired
points because route searching data around
these area were not stored. Reset the destination onto the road nearby. If
this road is one of the highways (gray
routes), an ordinary road nearby may be dis-
played as the recommended route.
Symptom Cause Remedy

BCM (BODY CONTROL MODULE) BCS-15
C
D E
F
G H
I
J
L
M A
B
BCS
Revision: 2005 July 2005 FX
WORK SUPPORT
Operation Procedure
1. Touch “BCM” on “SELECT TEST ITEM” screen.
2. Touch “WORK SUPPORT” on “SELECT DIAG MODE” screen.
3. Touch item on “SELECT WORK ITEM” screen.
4. Touch “START”.
5. Touch “CHANGE SET”.
6. The setting will be changed and “RESETTING COMPLETED” will be displayed.
7. Touch “END”.
Display Item List
CAN Communication Inspection Using CONSULT-II (Self-Diagnosis)AKS0058C
1. CHECK SELF-DIAGNOSTIC RESULT
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
1. Connect to CONSULT-II, and select “BCM” on “SELECT SYSTEM” screen.
2. Select “BCM control unit ” on “SELECT WORK ITEM” screen, and select “SELF-DIAG RESULTS”.
3. Check display content in self-diagnostic results.
Contents displayed
No malfunction>>INSPECTION END
Malfunction in CAN communication system>>After printing the monitor items, go to “CAN System”. Refer to LAN-5, "
Precautions When Using CONSULT-II" .
Item Description
RESET SETTING VALUE Return a value set with WORK SUPPORT of each system to a default value in factory shipment.
CONSULT-II display code Diagnosis item
U1000 INITIAL DIAG
TRANSMIT DIAG ECM
IPDM E/R
METER/M&A I-KEY