Page 1769 of 2893
(#'
)
Special Tools Required
20-92 Consoles
Center Console Removal/Installation
A
B C F
astener Locations
:Clip,4
A
Fastener Locations :Clip,3
B : Clip, 2
C
C B
B
B
C A
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S
RS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE: Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
Take care not to scratch the front seat, dashboard, and related parts.
1. Remove the passenger’s dashboard undercover (see page 20-104).
2. M/T model: Lower the shift lever boot (A) to release
the hooks (B) from the boot, then remove the shift
knob (C). 3.
Detach the clips by pulling the front inner panel (A)
up.
4. Gently pull out along the rear of the center console panel (A) to release the clips (B, C).
08/08/21 15:02:47 61SNR030_200_0094
ProCarManuals.com
DYNOMITE -2009-
Page 1770 of 2893
20-93
A
B
Fastener Locations :Bolt,2
A
B
5x0.8mm
5N·m
(0.5 kgf·m,
4lbf·ft) Fastener Locations
:Bolt,2 :Clip,2
5x0.8mm
5N·m
(0.5 kgf·m,
4lbf·ft)
B
A
5. Pull the center console panel (A) up and rearward to release the tabs (B).
6. Open the armrest (A), and remove the console box mat (B) to access and remove the bolts. 7. Remove the bolts and the clips from the front
portion of the center console. Disconnect the
console subharness connector (A), and detach the
connector clip (B).
(cont’d)
08/08/21 15:02:48 61SNR030_200_0095
ProCarManuals.com
DYNOMITE -2009-
Page 1771 of 2893
20-94Consoles
Center Console Removal/Installation (cont’d)
A
B
C
B
A
B A
BC
8. Slide both front seats all the way back, and recline
the seat-back fully.
9. Slide the center console (A) rearward to release the pins (B) from the bracket (C).
10. Lift up the rear of the console (A), and remove it from the dashboard.
11. If equipped, disconnect the seat heater switch connectors (B). 12. Install the console in the reverse order of removal,
and note these items:
Make sure each connector is plugged in properly.
If the clips are damaged or stress-whitened, replace them with new ones.
Push the clips and the hooks into place securely.
When installing the center console panel, install the tabs (A) into the notch (B) of the parking brake
base frame (C).
08/08/21 15:02:48 61SNR030_200_0096
ProCarManuals.com
DYNOMITE -2009-
Page 1772 of 2893

Î
(#'
")
S
pecial Tools Required
20-95
Center Console Disassembly/Reassembly
Fastener Locations
:TORXScrew,8
A A
BC
D
E F
G
H
I
I
A
A
B
C
D
KTC trim tool set SOJATP2014
NOTE:
Use the appropriate tool from the KTC trim tool set to
avoid damage when removing components.
Take care not to scratch the center console, the dashboard, and related parts.
1. Remove the center console (see page 20-92).
2. Remove the center console armrest (see page 20-96).
3. Remove the screws with a TORX T20 bit, and disconnect the console accessory power socket
connector (A). 4
. Release the hooks (A) and the pins (B), then
separate the left console side panel (C), the right
console side panel (D), the console beverage holder
(E) and the console box (F). If equipped, detach the
harness clips (G), then remove the console
subharness (H) from the hooks (I).
5. Release the hooks (A, B), then separate the console upper box (C) and the console lower box (D).
6. Assemble the console in the reverse order of disassembly, and make sure the console
subharness connector is plugged in properly.
08/08/21 15:02:49 61SNR030_200_0097
ProCarManuals.com
DYNOMITE -2009-
Page 1773 of 2893

(#'
) Î
Î
(#'
)
20-9620-96 Consoles
Center Console Armrest
Replacement
Armrest Lock Replacement
Fastener Locations
:Clip,5
A
A
B CFastener Locations
:TORXScrew,2
A
B
C
Fastener Locations :TORXScrew,2
NOTE: Take care not to scratch the armrest, center
console, and related parts.
1. Remove the center console (see page 20-92).
2. Gently pull out the center console rear cover (A) to detach the clips.
3. Open the armrest (A), pull the pin (B) off the armrest, then separate the armrest and the center
console (C).
4. Install the center console armrest in the reverse order of removal, and if the clips are damaged or
stress-whitened, replace them with new ones. NOTE: Take care not to scratch the armrest and related
parts.
1. Remove the center console armrest (see page 20-96).
2. Remove the screws with a TORX T15 bit. Slide the armrest liner (A) downward to release the hooks (B),
then remove the armrest liner and armrest spring
(C).
3. Remove the screws with a TORX T15 bit.
08/08/21 15:02:50 61SNR030_200_0098
ProCarManuals.com
DYNOMITE -2009-
Page 1774 of 2893
Î
20-97
Fastener Locations
:TORXScrew,2
AB
B A A
B
C
A
B
C
4. Slide the armrest (A) all the way forward, removethe screws with a TORX T15 bit, then remove the
armrest backbone (B).
5. From the back of the armrest backbone (A), push the edge of the armrest lock pin (B) with a flat-tip
screwdriver, then slide the armrest lock pin fully. 6. Remove the armrest lock (A) with the armrest lock
pin (B) from the armrest backbone (C).
7. Remove the armrest lock pin (A), then separate the armrest lock (B) and armrest lock spring (C).
8. Install the armrest lock in the reverse order of removal.
08/08/21 15:02:51 61SNR030_200_0099
ProCarManuals.com
DYNOMITE -2009-
Page 1775 of 2893

(#'
)
S
pecial Tools Required
20-98 Dashboard
Instrument Panel Removal/Installation
Fastener Locations
:Screw,3 F
astener Locations
:Clip,2
A
Fastener Locations : Clip, 6
A
B C
KTC trim tool set SOJATP2014
NOTE:
Take care not to scratch the instrument panel and
related parts.
Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
1. Remove these items:
Subdisplay visor (see page 20-100)
Navigation unit, with navigation system– ’06-08 models (see page 23-155)
– ’09 model (see page 23-355)
Audio unit, without navigation system – ’06-08 models (see page 23-80)
– ’09 model (see page 23-256)
2. Remove the screws. 3
. Detach the clips along the lower edge of the
instrument panel (A).
4. Detach the clips along the upper edge of the instrument panel (A). Gently pull out the instrument
panel to release the hooks (B) from the holder (C) of
the gauge control module.
5. Install the instrument panel in the reverse order of removal, and note these items:
If the clips are damaged or stress-whitened, replace them with new ones.
Push the clips into place securely.
08/08/21 15:02:52 61SNR030_200_0100
ProCarManuals.com
DYNOMITE -2009-
Page 1776 of 2893
(#' )
S
pecial Tools Required
20-99
Gauge Control Module (Speedo) Trim Removal/Installation
Fastener Locations
:Clip,4
AA Fa
stener Locations
: Clip, 5
A A A
B
B
C
KTC trim tool set SOJATP2014
NOTE:
Take care not to scratch the dashboard and related
parts.
Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
1. Pry up on the inside edge of the gauge control module (speedo) trim (A) with a trim tool to detach
the clips. 2
. Detach the clips and release the hooks (A) with a
trim tool, and the pins (B) along the edge of the
gauge control module (speedo) trim (C), then
remove the trim.
3. Install the trim in the reverse order of removal, and note these items:
If the clips are damaged or stress-whitened, replace them with new ones.
Push the clips into place securely.
08/08/21 15:02:52 61SNR030_200_0101
ProCarManuals.com
DYNOMITE -2009-