Page 1817 of 2893
(#'
)
Special Tools Required
20-13720-137
Rear Seat Armrest Beverage Holder
Replacement
A B
C
D
D
AB
C
D
4. Push the tab (A) to release the hook (B), and rotate the seat-back release lever (C) clockwise to release
the hook (D).
5. Install the release lever/cable in the reverse order of removal, and note these items:
Make sure the release cable is connected securely.
Make sure the seat-back locks securely and unlocks properly. KTC trim tool set SOJATP2014
NOTE:
Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
Take care not to tear or damage the seat covers.
1. Using a trim tool, push on the bottom ribs (A) of the rear hooks (B) to pull up the beverage holder (C),
then release the hooks from the wire (D).
(cont’d)
08/08/21 15:04:05 61SNR030_200_0139
ProCarManuals.com
DYNOMITE -2009-
Page 1818 of 2893
(#'
)
Special Tools Required
20-13720-137
Rear Seat Armrest Beverage Holder
Replacement
A B
C
D
D
AB
C
D
4. Push the tab (A) to release the hook (B), and rotate the seat-back release lever (C) clockwise to release
the hook (D).
5. Install the release lever/cable in the reverse order of removal, and note these items:
Make sure the release cable is connected securely.
Make sure the seat-back locks securely and unlocks properly. KTC trim tool set SOJATP2014
NOTE:
Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
Take care not to tear or damage the seat covers.
1. Using a trim tool, push on the bottom ribs (A) of the rear hooks (B) to pull up the beverage holder (C),
then release the hooks from the wire (D).
(cont’d)
08/08/21 15:04:05 61SNR030_200_0139
ProCarManuals.com
DYNOMITE -2009-
Page 1819 of 2893
(#'
)
20-13820-138 Seats
Rear Seat Armrest Beverage Holder
Replacement (cont’d)
Rear Seat Armrest Replacement
A
B C
B A
B
A
B
C
2. Release the front hooks (A) from the wire (B), then
remove the beverage holder (C).
3. Install the beverage holder in the reverse order of removal. Make sure the front hooks are installed
securely to the wire, then push down on the
beverage holder and install the rear hooks into the
wire securely. NOTE: Take care not to tear the seams or damage the
seat covers.
1. Remove the clip (A) from the left portion of the armrest pivot (B).
2. Slide the armrest (A) toward the driver’s side of the vehicle, and remove the pivot shaft (B) from the
collar (C) on the right side of the vehicle by pulling
back on the armrest.
08/08/21 15:04:05 61SNR030_200_0140
ProCarManuals.com
DYNOMITE -2009-
Page 1820 of 2893
(#'
)
20-13820-138 Seats
Rear Seat Armrest Beverage Holder
Replacement (cont’d)
Rear Seat Armrest Replacement
A
B C
B A
B
A
B
C
2. Release the front hooks (A) from the wire (B), then
remove the beverage holder (C).
3. Install the beverage holder in the reverse order of removal. Make sure the front hooks are installed
securely to the wire, then push down on the
beverage holder and install the rear hooks into the
wire securely. NOTE: Take care not to tear the seams or damage the
seat covers.
1. Remove the clip (A) from the left portion of the armrest pivot (B).
2. Slide the armrest (A) toward the driver’s side of the vehicle, and remove the pivot shaft (B) from the
collar (C) on the right side of the vehicle by pulling
back on the armrest.
08/08/21 15:04:05 61SNR030_200_0140
ProCarManuals.com
DYNOMITE -2009-
Page 1821 of 2893
(#'
)
Seat-back
20-13920-139
Rear Seat-back Cover Replacement
A B
C
A B Fastener Location
A
:Screw,1
3. Remove the pivot shaft (A) from the collar (B) on
the left, then remove the armrest (C).
4. Remove the collars (A) from the seat-back (B).
5. Install the armrest in the reverse order of removal. NOTE:
Take care not to tear the seams or damage the seat covers.
Put on gloves to protect your hands.
1. Remove the seat-back (see page 20-131).
2. Remove these items:
Armrest (see page 20-138)
Head restraint
3. Left seat-back: Remove the screw, then remove the center belt guide (A).
(cont’d)
08/08/21 15:04:06 61SNR030_200_0141
ProCarManuals.com
DYNOMITE -2009-
Page 1822 of 2893
(#'
)
Seat-back
20-13920-139
Rear Seat-back Cover Replacement
A B
C
A B Fastener Location
A
:Screw,1
3. Remove the pivot shaft (A) from the collar (B) on
the left, then remove the armrest (C).
4. Remove the collars (A) from the seat-back (B).
5. Install the armrest in the reverse order of removal. NOTE:
Take care not to tear the seams or damage the seat covers.
Put on gloves to protect your hands.
1. Remove the seat-back (see page 20-131).
2. Remove these items:
Armrest (see page 20-138)
Head restraint
3. Left seat-back: Remove the screw, then remove the center belt guide (A).
(cont’d)
08/08/21 15:04:06 61SNR030_200_0141
ProCarManuals.com
DYNOMITE -2009-
Page 1823 of 2893
20-140Seats
Rear Seat-back Cover Replacement (cont’d)
A
A
A B
C
A A
B C
Fastener Locations
:Clip,2
B : Clip, 2 C
Left seat-back C
B
Right seat-back B
C B
C A
4. Left seat-back: Pull out the center portion of the
armrest back panel (A) to release upper edge of the
armrest back panel.
5. Left seat-back: Pull out the armrest back panel (A) to release the hook (B) of the seat-back frame and
hook (C) of the seat-back cover. 6. Release the lower hook strip (A) and the clips (B, C).
08/08/21 15:04:07 61SNR030_200_0142
ProCarManuals.com
DYNOMITE -2009-
Page 1824 of 2893
Left seat-back
Right seat-back
20-141
A
B
B
B
A B
B A
B
C
C
7. Pull back the seat-back cover (A), then release the
hook strips (B). 8. Pull out the seat-back frame (A) from the pad (B),
then pinch the tabs on the ends of the head
restraint guides (C), and remove them from the
seat-back. The left seat-back is shown; the right
seat-back is similar.
9. Remove the seat-back cover and pad from the seat- back frame.
(cont’d)
08/08/21 15:04:07 61SNR030_200_0143
ProCarManuals.com
DYNOMITE -2009-