Page 1729 of 2893

(#')
Symptom Diagnostic procedure
20-54
Moonroof
Symptom Troubleshooting Index
Water leaks from moonroof 1.
2.
3.
4.
5.Check for a clogged drain tube.
Check for a gap between the glass weatherstrip and the roof panel
(see page 20-55).
Check for a defective or an improperly installed glass weatherstrip or drain
channel.
Check for a gap between the drain seal and the roof panel.
Adjust the moonroof position.
Wind noise from moonroof 1.
2.Check for excessive clearance between the glass weatherstrip and the roof
panel.
Adjust the moonroof position.
Motor noise from moonroof 1. 2.
3.Check for a loose motor.
Check for a worn gear or bearing.
Check for a deformed cable assembly.
Moonroof glass does not move,
but motor turns 1.
2.
3.
4.Check for a defective gear or inner cable.
Check for foreign matter stuck between the guide rail and the slider.
Check for a loose inner cable.
Make sure the cable assembly is attached properly.
Moonroof glass does not move
and motor does not turn (glass
can be moved with 5 mm
hexagonal wrench) 1.
2.
3.
4.Check for a blown fuse.
Check for a faulty moonroof switch.
Check for a run down battery.
Check for a defective motor control unit.
Moonroof glass does not stop at
proper flush closed position 1.
2.Reset the moonroof control unit (see page 22-287).
Check glass position adjustment.
During auto close operation,
moonroof glass r everses when
no object is trapped Check for dirt and debris in the track. Reset the moonroof control unit (see page
22-287).
Moonroof glass moves, but
there is no AUTO function Reset the moonroof control unit (see page 22-287).
08/08/21 15:00:18 61SNR030_200_0056
ProCarManuals.com
DYNOMITE -2009-
Page 1730 of 2893

´µ
´µ
´µ ´ µ
Î
(#'
") Î
(#'
)
´µ ´µ
´µ ´
µ
20-5520-55
Glass Position Adjustment Glass Replacement
13.5 1/ 1 mm
(0.55 0.04/ 0.04 in.)
AB
01/1mm
(0 0.04/ 0.04 in.)
Fastener Locations 5x0.8mm
4N·m
(0.4 kgf·m, 3 lbf·ft)
:TORXScrew,6
Front A
Fastener Locations
:Screw,2
Front
5x0.8mm
4N·m
(0.4 kgf·m, 3 lbf·ft)
F
:TORXScrew,6
BE
B
D
C
D C
A
E E
E
A
The roof panel (A) should be
even with the glass
weatherstrip (B), to within 0 1/ 1 mm
(0 0.04/ 0.04 in.) all the way around, and the distance
from glass edge to the roof panel edge should be
13.5 1/ 1 mm (0.55 0.04/ 0.04 in.). If not, make the
following adjustment:
1. Remove the bracket cover.
2. Adjust the glass (A). –1 Slightly loosen the screws with a TORX T25 bit.
–2 Move the glass up or down and forward orrearward.
–3 Tighten all screws securely.
3. If necessary, repeat on the opposite side. 1. Close the glass fully.
2. Slide the sunshade all the way back.
3. Pry out the lid (A), remove the screws (B), and
release the hooks (C), then remove both bracket
covers (D). Remove the screws (E) with a TORX T25
bit from both glass brackets (F).
4. Remove the glass (A) by lifting it up. Do not damage the roof panel.
5. Install the glass in the reverse order of the removal, and adjust the glass position alignment (see page
20-55).
6. Reset the moonroof control unit (see page 22-287).
7. Check for water leaks. Use free-flowing water from a hose without a nozzle. Do not use high-pressure
water.
NOTE: It is normal for some water to seep past the
moonroof into the moonroof frame, and exit
through the drains.
08/08/21 15:00:19 61SNR030_200_0057
ProCarManuals.com
DYNOMITE -2009-
Page 1731 of 2893
(#'
)
20-56 Moonroof
Wind Deflector Replacement
A
A B
C
A
1. Open the glass fully.
2. Remove the links (A) from both sides.
3. Remove the wind deflector (A). 4. Pry up on the deflector bases (A) and release the
hooks (B), then remove the bases with springs (C)
from both sides.
5. Install the deflector in the reverse order of removal.
6. Reset the moonroof control unit (see page 22-287).
08/08/21 15:00:20 61SNR030_200_0058
ProCarManuals.com
DYNOMITE -2009-
Page 1732 of 2893
(#'
)
20-57
Drain Channel Replacement
A
B A A
C
B
A
1. Remove the glass (see page 20-55).
2. Move both glass brackets (A) with a 5 mm hexagonal wrench to the position where the
moonroof normally tilts up, and disconnect the
drain channel rods (B) on both sides.
3. Slide the drain channel (A) forward. 4. Pull up the rear edge of the drain channel (A) while
pushing both clips (B), and release the channel
from both hooks (C) of the drain channel slider by
pulling it rearward.
5. Remove the drain channel.
6. Install the channel in the reverse order of removal, and note these items:
Push the clip portions into place securely.
Check the glass position adjustment (see page 20-55).
7. Check for water leaks. Let the water run freely from a hose without a nozzle. Do not use a high-pressure
spray.
08/08/21 15:00:20 61SNR030_200_0059
ProCarManuals.com
DYNOMITE -2009-
Page 1733 of 2893
(#'
)
20-58 Moonroof
Sunshade Replacement
Fastener Locations
:Screw,4
B
A Fastener Locations
:Screw,4
A B
1. Remove the drain channel (see page 20-57).
2. Slide the sunshade (A) until you can see both
sunshade slider spacers (B).
3. Remove the screws, then remove both spacers. 4. While lifting the front portion of the sunshade (A),
move the sunshade forward until you can see both
sunshade rear hooks (B). Do not damage the
sunshade or the hooks.
5. Remove the screws, then remove both rear hooks.
08/08/21 15:00:21 61SNR030_200_0060
ProCarManuals.com
DYNOMITE -2009-
Page 1734 of 2893
(#'
)
20-5920-59
Motor Replacement
A B
A Fastener Locations
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)A
B
:Bolt,2
6. Remove the sunshade (A).
7. Remove both front sunshade base sliders (A) and
both rear sunshade base sliders (B).
8. Install the sunshade in the reverse order of removal, and check the glass position adjustment (see page
20-55).
9. Check for water leaks. Let the water run freely from a hose without a nozzle. Do not use a high-pressure
spray. 1. Remove the headliner (see page 20-84).
2. Put on gloves to protect your hands. Disconnect the
connector (A), and remove the bolts, then remove
the motor (B).
3. Install the motor in the reverse order of removal, and note these items:
Make sure the connector is plugged in properly.
Reset the moonroof control unit (see page 22-287).
Check the motor operation.
08/08/21 15:01:20 61SNR030_200_0061
ProCarManuals.com
DYNOMITE -2009-
Page 1735 of 2893
(#'
)
20-5920-59
Motor Replacement
A B
A Fastener Locations
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)A
B
:Bolt,2
6. Remove the sunshade (A).
7. Remove both front sunshade base sliders (A) and
both rear sunshade base sliders (B).
8. Install the sunshade in the reverse order of removal, and check the glass position adjustment (see page
20-55).
9. Check for water leaks. Let the water run freely from a hose without a nozzle. Do not use a high-pressure
spray. 1. Remove the headliner (see page 20-84).
2. Put on gloves to protect your hands. Disconnect the
connector (A), and remove the bolts, then remove
the motor (B).
3. Install the motor in the reverse order of removal, and note these items:
Make sure the connector is plugged in properly.
Reset the moonroof control unit (see page 22-287).
Check the motor operation.
08/08/21 15:01:20 61SNR030_200_0061
ProCarManuals.com
DYNOMITE -2009-
Page 1736 of 2893

Î
(#'
)
20-60 Moonroof
Frame and Drain Tube Replacement
A
A B
C
A
A C
C
C
A
B Fastener Locations
:Bolt,9
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft) A
B
B
B
B B
C
A
SRS components are located in this area. Review the
SRS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
1. Remove these items: Headliner (see page 20-84)
Moonroof glass (see page 20-55)
2. Put on gloves to protect your hands. Disconnect the motor connector (A).
3. Disconnect the drain tubes (A).
4. Remove the roof wire harness (B) by detaching the harnessclips(C). 5. With an assistant holding the frame (A), remove the
bolts, starting at the rear, and release the rear
hooks (B) by moving the frame forward.
6. With the help of an assistant, carefully remove the frame through the front door opening. Take care
not to scratch the interior trim or the body, or tear
the seat covers.
7. To remove a front drain tube (A) from the body, remove the kick panel, left or right (see page 20-66),
and the driver’s dashboard undercover (see page
20-103) or the passenger’s dashboard undercover
(see page 20-104). Detach the clips (B) and remove
the drain valve (C) from the body hole, then remove
the front drain tube.
08/08/21 15:01:21 61SNR030_200_0062
ProCarManuals.com
DYNOMITE -2009-