2006 ACURA CSX Service Repair Manual

OBD port key tire type refuelling cruise control fuse box

Load previous 8 pages

Page 545 of 2893

ACURA CSX 2006 Service Repair Manual
(#

)
(#
)
11-22211-222 PGM-FI System
CMP Sensor B Replacement
CKP Sensor Replacement
C
B
A 12 N·m

Page 546 of 2893

ACURA CSX 2006 Service Repair Manual
(#
)
(#
)
M/T model
11-22311-223
Output Shaft (Countershaft) Speed
Sensor Replacement Knock Sensor

Page 547 of 2893

ACURA CSX 2006 Service Repair Manual
(#
)
(#
)
11-22411-224 PGM-FI System
MAP Sensor Replacement
MAF Sensor/IAT Sensor
Replacement
A B
C

Page 548 of 2893

ACURA CSX 2006 Service Repair Manual
(#

)

(#

)
11-22511-225
ECT Sensor 1 Replacement ECT Sensor 2 Replacement
A B
C
B
12 N·m (1.2

Page 549 of 2893

ACURA CSX 2006 Service Repair Manual

(#
)
11-226 PGM-FI System
ELD Replacement
A
A A
B
C
D
A
A A
A
1. Remove the ECM/PCM (see page 11-228).
2. Remove the under-hood fuse/re

Page 550 of 2893

ACURA CSX 2006 Service Repair Manual Ì
(#
!)
Special Tools Required
11-227
ECM/PCM Update
A
Honda diagnostic system (HDS) tablet tester
Honda interface module (HIM) and an iN worksta

Ì
(#'
!)
Special Tools Required
11-227
ECM/PCM Update
A
Honda diagnostic system (HDS) tablet tester
Honda interface module (HIM) and an iN workstation
with the latest HDS software version
HDS pocket tester
GNA 600 and iN workstation with the latest HDS software version
Any one of the above updating tools can be used.
NOTE: Make sure the HDS/iN workstation has the latest HDS software version.
Before you update the ECM/PCM, make sure the battery in the vehicle is fully charged, and connect a
jumper battery (not a battery charger) to maintain
system voltage.
Never turn the ignition switch to LOCK (0) or ACC (I) during the update. If there is a problem with the
update, l eave the ignition switch to ON (II).
To prevent ECM/PCM damage, do not operate anything electrical (headlights, audio system, brakes,
A/C, power windows, moonroof (if equipped), door
locks, etc.) during the update.
To ensure the latest program is installed, do an ECM/ PCM update when ever the ECM/PCM is substituted or
replaced.
You cannot update an ECM/PCM with a program it already has. It will only accept a new program.
High temperature in the engine compartment might cause the ECM/PCM to become too hot to run the
update. If the engine was running before this
procedure, open the hood, and cool the engine
compartment.
If you need to diagnose the Honda interface module (HIM) because the HIM’s red ( 3) light came on or
was flashing during the update, l eave the ignition
switch in ON (II) when you disconnect the HIM from
the data link connector (DLC). This will pr event ECM/
PCM damage. 1. Turn the ignition switch to ON (II), but do not start
the engine.
2. Connect the HDS to the data link connector (DLC) (A) located under the driver’s side of the dashboard.
3. Make sure the HDS communicates with the ECM/ PCM. If it doesn’t, go to the DLC circuit
troubleshooting (see page 11-204). If you are
returning from the DLC circuit troubleshooting, skip
steps 4 to 5 and clean the throttle body after
updating the ECM/PCM (see page 11- 344).
4. Select the INSPECTION MENU with the HDS.
5. Select the ETCS TEST, then select the TP POSITION CHECK, and follow the HDS screen prompts.
NOTE: If the TP POSITION CHECK indicates FAILED,
continue this procedure.
6. Exit the HDS diagnostic system, then select the update mode, and follow the screen prompts to
update the ECM/PCM.
(cont’d)
08/08/21 14:23:39 61SNR030_110_0227
ProCarManuals.com
DYNOMITE -2009-

Page 551 of 2893

ACURA CSX 2006 Service Repair Manual
(#
) Special Tools Required
11-22811-228 PGM-FI System
ECM/PCM Update (cont’d)
ECM/PCM Replacement
A
7. If the software in the ECM/PCM is the lates

Page 552 of 2893

Load next 8 pages

Page: < prev 1-10 ... 513-520 521-528 529-536 537-544 545-552 553-560 561-568 569-576 577-584 ... 2896 next >

service reset heating fuel filter location tire pressure automatic transmission lock