2006 ACURA CSX Service Repair Manual

height adjustment check engine sport mode TPMS deactivate passenger airbag jacking points

Popular search:

trunk release heating oil viscosity snow chains wheel heater fuel filter

Load previous 8 pages

Page 1017 of 2893

ACURA CSX 2006 Service Repair Manual Î Î
µ
µ µ
µ
µ
µ
YES
NO YES
NO
YES
NO
14-101
SG2 (GRN/BLK)
JUMPER WIRE
SHIFT SOLENOID WIRE HARNESS CONNECTOR
PCM CONNECTOR B (44P) SG2 (GRN/BLK) PCM CONNECTOR B (44P)
TATF (

Page 1018 of 2893

ACURA CSX 2006 Service Repair Manual µ
µ
µ
µ µ
µ
YES
NO
YES
NO YES
NO
14-102Automatic Transmission
DTC Troubleshooting (cont’d)
26. Monitor the OBD STATUS for P0713 in the DTCs
MENU with the HDS.
Troubleshooting is complete

Page 1019 of 2893

ACURA CSX 2006 Service Repair Manual
(#

)
µ
µ µ
µ
DTC P0716:
DTC P0717:
YES
NO YES
NO
14-103
PCM CONNECTOR C (44P)
LG2 (BRN/YEL)
LG1 (BRN/YEL)
Problem in Input Shaft
(Mainshaft)

(#'

)
µ
µ µ
µ
DTC P0716:
DTC P0717:
YES
NO YES
NO
14-103
PCM CONNECTOR C (44P)
LG2 (BRN/YEL)
LG1 (BRN/YEL)
Problem in Input Shaft
(Mainshaft) Speed Sensor Circuit
Problem in Input Shaft
(Mainshaft) Speed Sensor Circuit (No Signal
Input)
NOTE:
Before you troubleshoot, record all freeze data and any on-board snapshot with the HDS, and review
General Troubleshooting Information (see page 14-3).
This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the
transmission.
1. Check for proper input shaft (mainshaft) speed sensor installation (see page 14-227).
2. Turn the ignition switch to ON (II).
3. Clear the DTC with the HDS.
4. Block the rear wheels and raise the front of the vehicle, make sure it is securely supported, and
allow the front wheels to rotate freely, or raise the
vehicle on a lift.
5. Start the engine, disable the VSA by pressing the VSA OFF switch (if equipped), run the vehicle with
the shift lever in D at speeds over 20 km/h (12 mph)
for at least 10 seconds. Slow down and stop the
wheels.
6. Monitor the OBD STATUS for P0716 or P0717 in the DTCs MENU with the HDS.
Go to step 7.
If the HDS indicates PASSED, intermittent
failure, the system is OK at this time. Check for
poor connections or loose terminals between the
input shaft (mainshaft) speed sensor and the PCM.
If the HDS indicates NOT COMPLETED, go to step 5. 7. Turn the ignition switch to LOCK (0).
8. Jump the SCS line with the HDS.
9. Disconnect PCM connector C (44P).
10. Check for continuity between PCM connector terminal C40 and body ground, and between PCM
connector terminal C44 and body ground.
Go to step 11.
Repair open in the wires between PCM
connector terminals C40, C44, and body ground
(G101) (see page 22-16), or repair poor body
ground (G 101), then go to step 26.
(cont’d)
Terminal side of female terminals
Does the HDS ind icate F AILED? Is there continuity?
08/08/21 14:41:04 61SNR030_140_0105
ProCarManuals.com
DYNOMITE -2009-

Page 1020 of 2893

ACURA CSX 2006 Service Repair Manual
µ
µ µ
µ
YES
NO YES
NO
14-104Automatic Transmission
DTC Troubleshooting (cont’d)
INPUT SHAFT (MAINSHAFT)
SPEED SENSOR CONNECTOR
VCC2 (YEL/BLU) INPUT SHAFT
(MAINSHAFT)
SPEED SENSOR
CO

Page 1021 of 2893

ACURA CSX 2006 Service Repair Manual

µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
14-105
INPUT SHAFT (MAINSHAFT)
SPEED SENSOR CONNECTOR
NM (WHT/RED) SG2 (GRN/BLK)
INPUT SHAFT (MAINSHAFT)
SPEED SENSOR CON

Page 1022 of 2893

ACURA CSX 2006 Service Repair Manual µ
µ
µ
µ µ
µ µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
14-106Automatic Transmission
DTC Troubleshooting (cont’d)
26. Reconnect all connectors.
27. Turn the ignition switch to ON (II).
28. Clear

µ
µ
µ
µ µ
µ µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
14-106Automatic Transmission
DTC Troubleshooting (cont’d)
26. Reconnect all connectors.
27. Turn the ignition switch to ON (II).
28. Clear the DTC with the HDS.
29. Start the engine, run the vehicle with the shift lever
in D, and keep the vehicle at speeds over 20 km/h
(12 mph) for at least 10 seconds. Slow down and
stop the wheels.
30. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals between the input shaft (mainshaft)
speed sensor and the PCM, then go to step 1.
Go to step 31.
31. Monitor the OBD STATUS for P0716 or P0717 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 30,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for poor
connections or loose terminals between the input
shaft (mainshaft) speed sensor and the PCM, then
go to step 1. If the HDS indicates NOT COMPLETED,
go to step 29. 32. Reconnect all connectors.
33. Update the PCM if it does not have the latest
software (see page 11-227), or substitute a known-
good PCM (see page 11-7).
34. Start the engine, run the vehicle with the shift lever in D, and keep the vehicle at speeds over 20 km/h
(12 mph) for at least 10 seconds. Slow down and
stop the wheels.
35. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals between the input shaft (mainshaft)
speed sensor and the PCM. If the PCM was updated,
substitute a known-good PCM (see page 11-7), then
go to step 34. If the PCM was substituted, go to step
1.
Go to step 36.
36. Monitor the OBD STATUS for P0716 or P0717 in the DTCs MENU with the HDS.
If the PCM was updated, troubleshooting is
complete. If the PCM was substituted, replace the
original PCM (see page 11-228). If any other
Temporary DTCs or DTCs were indicated in step 35,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for poor
connections or loose terminals between the input
shaft (mainshaft) speed sensor and the PCM. If the
PCM was updated, substitute a known-good PCM
(see page 11-7), then go to step 34. If the PCM was
substituted, go to step 1. If the HDS indicates NOT
COMPLETED, go to step 34.
I s DT C P07 16 or P07 17 i nd i cat ed ?
Does the HDS ind icate PASSED? I s DT C P07 16 or P07 17 i nd i cat ed ?
Does the HDS ind icate PASSED?
08/08/21 14:41:06 61SNR030_140_0108
ProCarManuals.com
DYNOMITE -2009-

Page 1023 of 2893

ACURA CSX 2006 Service Repair Manual
(#

)
µ
µ
µ
µ µ
µ
DTC P0718:
YES
NO
YES
NO YES
NO
14-107
PCM CONNECTOR C (44P)
LG2 (BRN/YEL)
LG1 (BRN/YEL)
Input Shaft (Mainshaft) Speed
S

Page 1024 of 2893

ACURA CSX 2006 Service Repair Manual
Î
Î
µ
µ
µ
µ µ
µ
YES
NO
YES
NO YES
NO
14-108Automatic Transmission
DTC Troubleshooting (cont’d)
INPUT SHAFT (MAINSHAFT)
SPEED SENSOR CONNECTOR
VCC2 (YEL/BLU)
INPUT SHAFT

Load next 8 pages

Page: < prev 1-10 ... 985-992 993-1000 1001-1008 1009-1016 1017-1024 1025-1032 1033-1040 1041-1048 1049-1056 ... 2896 next >

lights open gas tank fuel pump wheel bolts steering wheel tire pressure

Popular search:

center console oil additives automatic transmission fluid seat memory child lock airbag off keyless