Page 1825 of 2893
Î
Left seat-back
Right seat-back
20-142 Seats
Rear Seat-back Cover Replacement (cont’d)
A
B
A B
D
B
C
A
10. Pull back the edge of the seat-back cover (A) all the
way around, and release the upholstery rings (B),
then remove the seat-back cover. 11. Install the cover in the reverse order of removal,
and note these items:
To prevent wrinkles when installing a seat-back cover, make sure the material is stretched evenly
over the pad before securing the upholstery rings,
the hooks, and the hook strips.
Replace all of the upholstery rings (A) fastening the seat-back cover (B) and the pad wire (C) with
new ones using commercially available
upholstery ring pliers (D).
08/08/21 15:04:08 61SNR030_200_0144
ProCarManuals.com
DYNOMITE -2009-
Page 1826 of 2893

Î
(#'
)
(#'
)
20-14320-143
Rear Seat Side Bolster Cover
Replacement Rear Seat Cushion Cover
Replacement
A
C
A
C C
B
A
B
AB
NOTE: Take care not to tear or damage the seat covers.
1. Remove the seat side bolster (see page 20-134).
2. Release all the hook strips (A), fold back the seat side bolster cover (B), and release the cover from
the hooks (C).
3. Install the cover in the reverse order of removal, and to prevent wrinkles when installing a side
bolster cover, make sure the material is stretched
evenly over the pad before securing the hook strips.NOTE:
Take care not to tear or damage the seat covers.
Put on gloves to protect your hands.
1. Remove the seat cushion (see page 20-133).
2. From the back of the seat-back, pass both lower retainers (A) through the slots in the seat cushion
pad, and release all the upholstery rings (B), and
fold back the seat cushion cover.
3. Pull back the edge of the seat cushion cover all the way around, and release the upholstery rings (A),
from the seat cushion cover (B) through the hole in
the seat cushion pad, then remove the seat cushion
cover.
(cont’d)
08/08/21 15:04:08 61SNR030_200_0145
ProCarManuals.com
DYNOMITE -2009-
Page 1827 of 2893
Î
Î
(#'
)
20-14420-144 Seats
Rear Seat Cushion Cover
Replacement (cont’d)
Rear Seat Armrest Cover
Replacement
D
B
C
A
A
B C
4. Install the cover in the reverse order of removal,
and note these items:
To prevent wrinkles when installing a seat cushion cover, make sure the material is
stretched evenly over the pad before securing
the retainers and upholstery rings.
Replace all of the upholstery rings (A) fastening the seat-back cover (B) and the pad wire (C) with
new ones using commercially available
upholstery ring pliers (D). NOTE: Take care not to tear or damage the seat covers.
1. Remove the armrest from the seat-back (see page 20-138).
2. Remove the armrest beverage holder from the armrest (see page 20-137).
3. Release the clips (A) and the hook strip (B), and pull back the armrest cover (C) all the way around.
08/08/21 15:04:09 61SNR030_200_0146
ProCarManuals.com
DYNOMITE -2009-
Page 1828 of 2893
Î
Î
(#'
)
20-14420-144 Seats
Rear Seat Cushion Cover
Replacement (cont’d)
Rear Seat Armrest Cover
Replacement
D
B
C
A
A
B C
4. Install the cover in the reverse order of removal,
and note these items:
To prevent wrinkles when installing a seat cushion cover, make sure the material is
stretched evenly over the pad before securing
the retainers and upholstery rings.
Replace all of the upholstery rings (A) fastening the seat-back cover (B) and the pad wire (C) with
new ones using commercially available
upholstery ring pliers (D). NOTE: Take care not to tear or damage the seat covers.
1. Remove the armrest from the seat-back (see page 20-138).
2. Remove the armrest beverage holder from the armrest (see page 20-137).
3. Release the clips (A) and the hook strip (B), and pull back the armrest cover (C) all the way around.
08/08/21 15:04:09 61SNR030_200_0146
ProCarManuals.com
DYNOMITE -2009-
Page 1829 of 2893
20-145
AB A
4. Release the armrest cover from the armrest pivot
portions (A), then remove it from the pad (B).
5. Install the cover in the reverse order of removal. To prevent wrinkles when installing an armrest cover,
make sure the material is stretched evenly over the
pad before securing the clips and the hook strips.
08/08/21 15:04:09 61SNR030_200_0147
ProCarManuals.com
DYNOMITE -2009-
Page 1830 of 2893
Î
(#'
)
’06-08 models
’09 model
20-146Bumpers
Front Bumper Removal/Installation
Fastener Locations
:Screw,2
A : Clip, 2 B:Clip,6C
A B
C
D E
E
C CC
C C
B A
E
E Fastener Locations
:Screw,2
A : Clip, 10
C
C
A A
C
C
C
C
C
C
C
C
C
D E
E
A B
C
NOTE: Have an assistant help you when removing and installing the front bumper.
Take care not to scratch the front bumper and body.
Put on gloves to protect your hands.
1. Remove these items: Front fender trim (see page 20-162)
Front grille cover (see page 20-163)
2. Remove the screws (A) and the clips (B, C) securing the front bumper (D).
NOTE: To release the clips, pry up on the center pin
at the notch (E).
3. Pull on the front bumper (A) at the wheel arch areasto release it from the hooks (B) on the side spacers
(C).
08/08/21 15:04:10 61SNR030_200_0148
ProCarManuals.com
DYNOMITE -2009-
Page 1831 of 2893
Î
20-147
A
B
C
B
A
A
B C
B
4. With the help of an assistant, while pulling the wheel arch portion away from the side spacer (A),
pull the front bumper to release the bumper from
the hooks (B) on the corner upper beam (C).
5. If equipped, disconnect the front fog light connectors (A) while holding the front bumper (B),
then remove the bumper. 6. Release the hooks (A), then remove the front
bumper absorber (B) from the front bumper beam
(C).
7. Install the bumper in the reverse order of removal, and note these items:
Make sure the front bumper engages the hooks (of both corner upper beams and side spacers)
on each side securely.
If the clips are damaged or stress-whitened, replace them with new ones.
Push the clips and the hooks into place securely.
08/08/21 15:04:10 61SNR030_200_0149
ProCarManuals.com
DYNOMITE -2009-
Page 1832 of 2893

Î
(#'
) Î
(#'
)
’09 Model ’09 Model
20-14820-148Bumpers
Front Bumper Lower Grille
Replacement
Front Bumper Lower Side Plate
Replacement
Fastener Locations
:Clip,6
D D
B
C
A A
A
A
A Fastener Locations
:Clip,12
D
B A
D
C
NOTE: Take care not to scratch the front bumper.
Put on gloves to protect your hands.
1. Remove the front bumper (see page 20-146).
2. Detach the clips and release the hooks (A), then remove the front bumper lower grille (B) from the
front bumper (C).
NOTE: To release the clips, pry up on the center pin
at the notch (D).
3. Install the grille in the reverse order of removal, and note these items:
If the clips are damaged or stress-whitened, replace them with new ones.
Push the clips and the hooks into place securely. NOTE:
Take care not to scratch the front bumper.
Put on gloves to protect your hands.
1. Detach the clips, then remove the left front bumper lower side plate (A) and the right front bumper
lower side plate (B) from the front bumper (C).
NOTE: To release the clips, pry up on the center pin
at the notch (D).
2. Install the plate in the reverse order of removal, and note these items:
If the clips are damaged or stress-whitened, replace them with new ones.
Push the clips into place securely.
08/08/21 15:04:11 61SNR030_200_0150
ProCarManuals.com
DYNOMITE -2009-