2006 ACURA CSX Service Repair Manual

weight child restraint audio navigation system lane assist check engine

Popular search:

tire pressure reset power steering Radiator fuel tank capacity fuse box cruise control alarm

Load previous 8 pages

Page 169 of 2893

ACURA CSX 2006 Service Repair Manual

Î

M/T model
A/T model
6-25
10x1.25mm
44 N·m
(4.5 kgf·m, 33 lbf·ft)
D
A C
B
6x1.0mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft) A
A
21. Install the side engine mount bracket.
22. Install

Page 170 of 2893

ACURA CSX 2006 Service Repair Manual

6-26Cylinder Head
Cam Chain Installation (cont’d)
A
A 12x1.25mm
72 N·m
(7.3 kgf·m, 52 lbf·ft)
14x1.5mm
74 N·m
(7.5 kgf·m, 54 lbf·ft)
26. Raise the vehicle on the lift.
27. Loosen

Page 171 of 2893

ACURA CSX 2006 Service Repair Manual

M/T model
A/T model
6-27
12x1.25mm
74 N·m
(7.5 kgf·m, 54 lbf·ft)
12x1.25mm
74 N·m
(7.5 kgf·m, 54 lbf·ft) 14x1.5mm
93 N·m
(9.5 kgf·m, 69 lbf·ft)
31. Tighten the transmission moun

Page 172 of 2893

ACURA CSX 2006 Service Repair Manual

Î
M/T model
A/T model
6-28 Cylinder Head
Cam Chain Installation (cont’d)
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
12x1.25mm
64 N·m
(

Page 173 of 2893

ACURA CSX 2006 Service Repair Manual

(#
)

Removal
6-29
Auto-tensioner Removal and Installation
C
B
A
1. Remove the chain case cover.
2. Turn the crankshaft counterclockwise

Page 174 of 2893

ACURA CSX 2006 Service Repair Manual

Installation
6-30Cylinder Head
Auto-tensioner Removal and Installation (cont’d)
6x1.0mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
1. Install the

Page 175 of 2893

ACURA CSX 2006 Service Repair Manual

(#
)

µ µ
µµ
Special Tools Required
Oil Seal Installed Height:
33.0 33.7 mm (1.30 1.33 in.)
6-31
Chain Case Oil Seal Installation
07749-00

Page 176 of 2893

ACURA CSX 2006 Service Repair Manual
(#
") Tensioner Rod Length
Service Limit: 13.5 mm (0.53 in.)
6-32
Cylinder Head
Cam Chain Inspection
13.5 mm (0.53 in.)
1. Remove the right front whee

(#'
") Tensioner Rod Length
Service Limit: 13.5 mm (0.53 in.)
6-32
Cylinder Head
Cam Chain Inspection
13.5 mm (0.53 in.)
1. Remove the right front wheels.
2. Remove the splash shield (see step 25 on page 5-5).
3. Remove the drive belt (see page 4-31).
4. Remove the cylinder head cover (see page 6-36).
5. Set the No. 1 piston at top dead center (TDC). The
punch mark on the variable valve timing control
(VTC) actuator and the punch mark on the exhaust
camshaft sprocket should be at the top. Align the
TDC marks on the VTC actuator and the exhaust
camshaft sprocket (see step 5 on page 6-18).
6. Disconnect the crankshaft position (CKP) sensor connector and the VTC oil control solenoid valve
connector, and remove the harness clamps (see
step 6 on page 6-18).
7. Remove the VTC oil control solenoid valve (see page 11-294).
8. Remove the crankshaft pulley (see page 6-16).
9. Support the engine with a jack and a wood block under the oil pan.
10. Remove the upper torque rod (see step 10 on page 6-18).
11. Remove the ground cable, then remove the side engine mount bracket (see step 11 on page 6-19).
12. Remove the side engine mount bracket (see step 12 on page 6-19).
13. Remove the cam chain case (see step 13 on page 6-19). 14. Measure the tensioner rod length between the
tensioner body and bottom of the flat surface
section on the tensioner rod. If the length is more
than the service limit, replace the cam chain and
the oil pump chain.
15. Check the chain case oil seal for damage. If the oil seal is damaged, replace the chain case oil seal
(see page 6-31).
16. Remove all of the old liquid gasket from the chain case mating surfaces, bolt and bolt holes.
17. Clean, and dry the chain case mating surfaces.
18. Apply liquid gasket, P/N 08717-0004, 08718-0001, 08718-0003, or 08718-0009, evenly to the engine
block mating surface of the chain case, and to the
inside edge of the threaded bolt holes. Install the
component within 5 minutes of applying the liquid
gasket(seestep17onpage6-24).
NOTE: If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes.
If too much time has passed after applying the liquid gasket, remove the old liquid gasket and
residue, then reapply new liquid gasket.
19. Apply liquid gasket to the engine block upper surface contact areas on the chain case and lower
block upper surface contact areas on the chain case
(see step 18 on page 6-24).
08/08/21 14:27:24 61SNR030_060_0032
ProCarManuals.com
DYNOMITE -2009-

Load next 8 pages

Page: < prev 1-10 ... 137-144 145-152 153-160 161-168 169-176 177-184 185-192 193-200 201-208 ... 2896 next >

warning light towing airbag disable reset infotainment system carplay brake pads replacement

Popular search:

high beam wheel bolts display change wheel service interval reset CD changer CD player