2006 ACURA CSX Service Repair Manual

brake maintenance reset width winter tyres fuse chart washer fluid

Popular search:

hood open charging parking brake remote start rear view mirror brakes heater

Load previous 8 pages

Page 1001 of 2893

ACURA CSX 2006 Service Repair Manual ÎÎ
µ
µ µ
µ
YES
NO
YES
NO
14-85
ATPR (WHT)
GND (BLK)
TRANSMISSION RANGE
SWITCH CONNECTOR
PCM CONNECTOR B (44P)
ATPR (WHT)
15. Measure the voltage between transmission rangeswitch co

Page 1002 of 2893

ACURA CSX 2006 Service Repair Manual ÎÎ
µ
µ µ
µ
YES
NO
YES
NO
14-86Automatic Transmission
DTC Troubleshooting (cont’d)
GND (BLK)
TRANSMISSION RANGE
SWITCH CONNECTOR
ATPN
(RED/BLK) PCM CONNECTOR B (44P)
ATPN (RED/BLK

Page 1003 of 2893

ACURA CSX 2006 Service Repair Manual ÎÎ
µ
µ µ
µ
YES
NO
YES
NO
14-87
ATPD (PNK)TRANSMISSION RANGE
SWITCH CONNECTOR
GND (BLK) PCM CONNECTOR B (44P)
ATPD (YEL/GRN)
25. Measure the voltage between transmission rangeswitch

Page 1004 of 2893

ACURA CSX 2006 Service Repair Manual ÎÎ

µ
µ µ
µ
YES
NO
YES
NO
14-88Automatic Transmission
DTC Troubleshooting (cont’d)
ATPS (BLU)
GND (BLK)
TRANSMISSION RANGE
SWITCH CONNECTOR
PCM CONNECTOR B (44P)
ATPS (RED)
30. Me

Page 1005 of 2893

ACURA CSX 2006 Service Repair Manual Î

Î

µ
µ µ
µ
YES
NO
YES
NO
14-89
ATPFWD (YEL/RED)
GND (BLK)
TRANSMISSION RANGE
SWITCH CONNECTOR
PCM CONNECTOR B (44P)
ATPFWD (BLU/YEL)
35. Measure the voltage between transmission ra

Page 1006 of 2893

ACURA CSX 2006 Service Repair Manual Î
Î

µ
µ µ
µ
YES
NO
YES
NO
14-90Automatic Transmission
DTC Troubleshooting (cont’d)
TRANSMISSION RANGE
SWITCH CONNECTOR
ATPRVS
(WHT/RED)
GND (BLK) PCM CONNECTOR B (44P)
ATPRVS (RED

Page 1007 of 2893

ACURA CSX 2006 Service Repair Manual µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
14-91
45. Reconnect all connectors.
46. Turn the ignition switch to ON (II).
47. Clear the DTC with the HDS.
48. Start the engine.
49. With

µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
14-91
45. Reconnect all connectors.
46. Turn the ignition switch to ON (II).
47. Clear the DTC with the HDS.
48. Start the engine.
49. With the brake pedal pressed, move the shift lever
through all positions. Stop for at least 1 second in
each position.
50. Check for Temporary DTCs or DTCs with the HDS.
Check for intermittent short to body ground
in the wires between the transmission range switch
and the PCM, then go to step 1.
Go to step 51.
51. Monitor the OBD STATUS for P0705 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 50,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for
intermittent short to body ground in the wires
between the transmission range switch and the
PCM, then go to step 1. If the HDS indicates NOT
COMPLETED, go to step 48.
52. Reconnect all connectors.
53. Update the PCM if it does not have the latest software (see page 11-227), or substitute a known-
good PCM (see page 11-7).
54. Start the engine.
55. With the brake pedal pressed, move the shift lever through all positions. Stop for at least 1 second in
each position. 56. Check for Temporary DTCs or DTCs with the HDS.
Check for intermittent short to body ground
in the wires between the transmission range switch
and the PCM. If the PCM was updated, substitute a
known-good PCM (see page 11-7), then go to step
54. If the PCM was substituted, go to step 1.
Go to step 57.
57. Monitor the OBD STATUS for P0705 in the DTCs MENU with the HDS.
If the PCM was updated, troubleshooting is
complete. If the PCM was substituted, replace the
original PCM (see page 11-228). If any other
Temporary DTCs or DTCs were indicated in step 56,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for
intermittent short to body ground in the wires
between the transmission range switch and the
PCM. If the PCM was updated, substitute a known-
good PCM (see page 11-7), then go to step 54. If the
PCM was substituted, go to step 1. If the HDS
indicates NOT COMPLETED, go to step 54.
Is DT C P07 05 ind icated ?
Does the HDS ind icate PASSED? Is DT C P07 05 ind icated ?
Does the HDS ind icate PASSED?
08/08/21 14:41:01 61SNR030_140_0093
ProCarManuals.com
DYNOMITE -2009-

Page 1008 of 2893

ACURA CSX 2006 Service Repair Manual (#

)
µ
µ
µ
µ µ
µ
µ
µ
µ
µ
DTC P0706:
YES
NO
YES
NO YES
NO
YES
NO
YES
NO
14-92
Automatic Transmission
DTC Troubleshooting (cont’d)
Ope

(#'

)
µ
µ
µ
µ µ
µ
µ
µ
µ
µ
DTC P0706:
YES
NO
YES
NO YES
NO
YES
NO
YES
NO
14-92
Automatic Transmission
DTC Troubleshooting (cont’d)
Open in Transmission Range
Switch Circuit
NOTE:
Before you troubleshoot, record all freeze data and any on-board snapshot with the HDS, and review
General Troubleshooting Information (see page 14-3).
This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the
transmission.
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Block the rear wheels and raise the front of the vehicle, make sure it is securely supported, and
allow the front wheels to rotate freely, or raise the
vehicle on a lift.
4. Start the engine, disable the VSA by pressing the VSA OFF switch (if equipped), run the vehicle with
the shift lever in D until the vehicle speed reaches
40 km/h (25 mph), then slow down and stop the
wheels.
5. Monitor the OBD STATUS for P0706 in the DTCs MENU with the HDS.
Go to step 6.
If the HDS indicates PASSED, intermittent
failure, the system is OK at this time. Check for
poor connections or loose terminals between the
transmission range switch and the PCM. If the HDS
indicates NOT COMPLETED, go to step 4.
6. Turn the ignition switch to LOCK (0).
7. Inspect the transmission range switch (see page 14-265).
Go to step 8.
Replace the transmission range switch
(see page 14-267), then go to step 25.
8. Adjust the shift cable (see page 14-259). 9. Turn the ignition switch to ON (II).
10. Clear the DTC with the HDS.
11. Start the engine, disable the VSA by pressing the VSA OFF switch (if equipped), run the vehicle with
the shift lever in D until the vehicle speed reaches
40 km/h (25 mph), then slow down and stop the
wheels.
12. Monitor the OBD STATUS for P0706 in the DTCs MENU with the HDS.
Go to step 13.
If the HDS indicates PASSED, troubleshooting
is complete. If the HDS indicates NOT COMPLETED,
go to step 11.
13. Shift to D, and check the Forward Switch (ATPFWD) andA/TDSwitchintheDATALISTwiththeHDS.
Go to step 14.
Go to step 18.
14. Shift to S, and check the Forward Switch (ATPFWD) andA/TSSwitchintheDATALISTwiththeHDS.
Go to step 15.
Go to step 18.
Does the HDS ind icate F AILED?
Is the switch OK ? Does the HDS ind icate F AILED?
Ar e F or w ar d Sw i t ch ( AT PF W D) and A/ T D Sw i t chON?
Ar e F or w ar d Sw i t ch ( AT PF W D) and A/ T S Sw i t chON?
08/08/21 14:41:01 61SNR030_140_0094
ProCarManuals.com
DYNOMITE -2009-

Load next 8 pages

Page: < prev 1-10 ... 969-976 977-984 985-992 993-1000 1001-1008 1009-1016 1017-1024 1025-1032 1033-1040 ... 2896 next >

lug pattern change wheel tire pressure reset brake fluid turn signal bulb reset infotainment system

Popular search:

start stop button jack points tire size wiper fluid adding oil wiring brake pads