2006 ACURA CSX oil capacity

µµ
µµµµµµ
µµ
µµ
•••
µµ
µµ
µµ
µµ
µµ
µµ
µµ
µµ
Engine Lubrication
Item Measurement QualificationStandard or New Service Limit
2-5
Engine oil Capacity (K20Z2) Engine overhaul 5.3 L (5.6 US qt)
Oil change
including filter 4.2L(4.4USqt)
Oil change
without filter 4.0L(4.2USqt)
Capacity (K20Z3) Engine overhaul 5.5 L (5.8 US qt)
Oil change
including filter 4.4L(4.6USqt)
Oil change
without filter 4.2L(4.4USqt)
Oil pump Inner-to-outer rotor clearance 0.06 0.16 mm (0.002 0.006 in.) 0.20 mm (0.008 in.)
Pump housing-to-outer rotor clearance 0.15 0.21 mm (0.006 0.008 in.) 0.23 mm (0.009 in.)
Pump housing-to-rotor axial clearance 0.035 0.070 mm (0.0014 0.0028 in.) 0.12 mm (0.005 in.)
Balancer shafts, journal diameter No. 1 journal, front shaft19.938 19.950 mm (0.7850 0.7854 in.) 19.92 mm (0.784 in.)
No. 1 journal,
rear shaft 23.938 23.950 mm (0.9424 0.9429 in.) 23.92 mm (0.942 in.)
No. 2 journal,
front and rear
shaft 32.949 32.961 mm (1.2972 1.2977 in.) 32.93 mm (1.296 in.)
Balancer shafts, journal taper 0.005 mm (0.0002 in.) max.
Balancer shafts, end play Front0.063 0.108 mm (0.0025 0.0043 in.) 0.14 mm (0.0055 in.)
Rear 0.063 0.108 mm (0.0025 0.0043 in.) 0.14 mm (0.0055 in.)
Balancer shafts, shaft-to-bearing
clearance No. 1 journal,
front shaft0.050 0.082 mm (0.0020 0.0032 in.) 0.10 mm (0.004 in.)
No. 1 journal,
rear shaft 0.050 0.082 mm (0.0020 0.0032 in.) 0.10 mm (0.004 in.)
No. 2 journal,
front and rear
shaft 0.060 0.120 mm (0.0024 0.0047 in.) 0.15 mm (0.006 in.)
Balancer shaft bearings, I.D. No. 1 journal,
front shaft 20.000 20.020 mm (0.7874 0.7882 in.) 20.03 mm (0.789 in.)
No. 1 journal,
rear shaft 24.000 24.020 mm (0.9449 0.9457 in.) 24.03 mm (0.946 in.)
No. 2 journal,
front and rear
shaft 33.021 33.069 mm (1.3000 1.3019 in.) 33.09 mm (1.303 in.)
Relief valve, oil pressure with oil
temperature at 80 °C (176 °F) At idle
70 kPa (0.7 kgf/cm , 10 psi) min.
At 3,000 rpm 300 kPa (3.1 kgf/cm , 44 psi) min.
2
2
08/08/21 14:07:14 61SNR030_020_0005
ProCarManuals.com
DYNOMITE -2009-

µµµµ
µµ
µµ
•••
••• µµ
µµ
µµ
µµ
µµ µ
µµ
Brakes
Air Conditioning
Item Measurement QualificationStandard or New Service Limit
Item Measurement Qualification Standard or New
2-19
Parking brake Distance traveled when lever pulled
with 196 N (20 kgf, 44 lbf) of force 8to10clicks
Brake pedal Pedal height (carpet moved aside) M/T 153 mm (6.02 in.) A/T 158 mm (6.22 in.)
Free play 1 5 mm (0.04 0.20 in.)
Brake disc Thickness Front (except TYPE S)22.9 23.1 mm (0.90 0.91 in.) 21.0 mm (0.83 in.)
Front (TYPE S) 24.9 25.1 mm (0.98 0.99 in.) 23.0 mm (0.91 in.)
Rear 8.9 9.1 mm (0.35 0.36 in.) 8.0 mm (0.31 in.)
Runout Front and rear 0.04 mm (0.0016 in.)
Parallelism Front and rear 0.015 mm (0.0006 in.)
Brake pad Thickness Front (except TYPE S)9.6 10.2 mm (0.38 0.40 in.) 1.6 mm (0.06 in.)
Front (TYPE S) 9.0 9.7 mm (0.35 0.38 in.) 1.6 mm (0.06 in.)
Rear 8.3 9.4 mm (0.33 0.37 in.) 1.6 mm (0.06 in.)
Refrigerant Type HFC-134a (R-134a) Capacity of system 400 450 g (14.1 15.8 oz)
Refrigerant oil Type SP-10 (P/N 38897-P13-A01) Capacity of components Condenser 50 mL (1 2/3 fl·oz) Evaporator 40 mL (1 1/3 fl·oz)
Each Line and
hose10 mL (1/3 fl·oz)
Compressor 75 85mL(21/2 25/6fl·oz)
Compressor Field coil resistance At 20 °C (68 °F) 3.15 3.45 Pulley-to-armature-plate clearance 0.35 0.65 mm (0.014 0.026 in.)
08/08/21 14:07:17 61SNR030_020_0019
ProCarManuals.com
DYNOMITE -2009-

(#')Symbol Maintenance Main Items
3-7
Maintenance Main Items
If the message ‘‘SERVICE’’ does not appear more than 12 months after the display is reset, change the engine oil every
year.
NOTE:


 Replace the brake fluid every 3 years independent of the maintenance messages in the information display.
Inspect idle speed every 160,000 miles (256,000 km).
Adjust the valves during services A, B, 1, 2 or 3, only if they are noisy.

















A Replace engine oil (see page 8-10).
Engine oil capacity without oil filter:
K20Z2: 4.0 L (4.2 US qt)
K20Z3: 4.2 L (4.4 US qt)
B Replace engine oil and oil filter (see page 8-11). Engine oil capacity with oil filter:
K20Z2: 4.2 L (4.4 US qt)
K20Z3: 4.4 L (4.6 US qt)
Check front and rear brakes (see page 19-3). Check pad and disc for wear (thickness), damage, and cracks.
Check calipers for damage, leaks, and tightness of mounting bolts.
Check parking brake adjustment (see page 19-7). Check the number of clicks (8 to 10) when the parking brake lever is pulled with 196 N (20 kgf,
44 lbf) of force.
Inspect tie-rod ends, steering gearbox, and gearbox boots (see page 17-5). Check steering linkage.
Check boots for damage and leaking grease.
Check fluid lines for damage and leaks.
Inspect suspension components (see page 18-3). Check bolts for tightness.
Check condition of ball joint boots for deterioration and damage.
Inspect driveshaft boots (see page 16-4). Check boots for cracks and boot bands for tightness.
Inspect brake hoses and lines including VSA lines (see page 19-37). Check the master cylinder and VSA modulator-control unit for damage or leakage.
Inspect all fluid levels and condition of fluids. Engine coolant (see page 10-7)
Automatic transmission fluid (ATF-Z1) (see page 14-231)
Manual transmission fluid (MTF)
5M/T (see page 13-5), 6M/T (see page 13-82)
Clutch fluid (see page 12-7)
Brake fluid (see page 19-9)
Windshield washer fluid (see page 22-234)
Inspect exhaust system: K20Z2 (see page 9-13), K20Z3 (see page 9-14)
Check catalytic converter heat shields, exhaust pipes, and muffler for damage, leaks, and tightness.
Inspect fuel lines (see page 11-326) and connections (see page 11-328). Check for loose connections, cra cks, and deterioration; retighten loose connections and replace
damaged parts.
NOTE: According to state and federal regulations, failure to do the maintenance items marked with an asterisk ( ) will
not void the client’s emissions warranties. However, Acura recommends that all maintenance services be done at the
recommended interval, to ensure long-term reliability.
08/08/21 14:08:32 61SNR030_030_0007
ProCarManuals.com
DYNOMITE -2009-


(#') 

(#'
 )
Engine Oil Temperature: 80 °C (176 °F)
Engine Oil Pressure:
At Idle: 70 kPa (0.7 kgf/cm , 10 psi) min.
At 3,000 rpm: 300 kPa (3.1 kgf/cm , 44 psi) min.
K20Z2 engine
Capacity
AtOilChange:4.0L(4.2USqt)
At Oil Change including Filter: 4.2 L (4.4 US qt)
After Engine Overhaul: 5.3 L (5.6 US qt)
K20Z3 engine
Capacity
AtOilChange:4.2L(4.4USqt)
At Oil Change including Filter: 4.4 L (4.6 US qt)
After Engine Overhaul: 5.5 L (5.8 US qt)
2
2
8-108-10Engine Lubrication
Oil Pressure Test
Engine Oil Replacement
A A
39 N·m
(4.0 kgf·m, 29 lbf·ft)
B
NOTE: If the oil pressure warning indicator stays on
with the engine running, check the engine oil l
evel. If
the oil level is correct do the following test:
1. With the engine stopped, remove the oil pressure switch (see page 8-9), then install an oil pressure
gauge (A).
2. Start the engine. Shut it off immediately if the gauge registers no oil pressure. Repair the problem
before continuing.
3. Allow the engine to reach operating temperature (fan comes on at least twice). The pressure should
be:
4. If the oil pressure is out of specifications, inspect these items:
 Blocking of oil filter (see page 8-11).
 Blocking of oil screen.
 Inspect the oil pressure relief valve (see page 8-15).
 Inspect the oil pump (see page 8-17). 1. Warm up the engine.
2. Remove the drain bolt (A), and drain the engine oil.
3. Reinstall the drain bolt with a new washer (B).
4. Refill the engine with the recommended oil
(see page 3-2).
Do not overtighten.
08/08/21 14:36:43 61SNR030_080_0010
ProCarManuals.com
DYNOMITE -2009-

Î
 
(#'



 )
Automatic Transmission Fluid Capacity:
2.9 L (3.1 US qt) at change
6.5 L (6.9 US qt) at overhaul
14-232 Automatic Transmission
ATF Replacement
A
18 x 1.5 mm
49 N·m
(5.0 kgf·m,
36 lbf·ft)
B
ATF
A
NOTE: Keep all foreign particles out of the transmission. 1. Park the vehicle on the level ground.
2. Warm up the engine to normal operating temperature (the radiator fan comes on), and turn
the engine off.
3. Remove the drain plug (A), and drain the automatic transmission fluid (ATF).
4. Reinstall the drain plug with a new sealing washer (B).
5. Refill the transmission with ATF into the dipstick hole to bring the fluid level between the upper
mark and the lower mark of the dipstick. Always
use Acura ATF-Z1 automatic transmission fluid
(ATF). Using a non-Acura ATF can affect shift
quality.
6. Check that the ATF level is between the upper mark
and the lower mark of the dipstick.
7. Insert the dipstick back into the transmission with the letters ‘‘ATF’’ pointing toward the front of the
vehicle. 8. If the maintenance minder required to replace the
ATF, reset the maintenance minder (see page 3-4),
and this procedure is complete. If the maintenance
minder did not require you to replace the ATF, go
to step 9.
9. Connect the HDS to the DLC (A) located under the driver’s side of the dashboard.
10. Turn the ignition switch to ON (II). Make sure the HDS communicates with the PCM. If it does not, go
to the DLC circuit troubleshooting (see page
11-204).
11. Select BODY ELECTRICAL with the HDS.
12. Select ADJUSTMENT in the GAUGES MENU with the HDS.
13. Select RESET in the MAINTENANCE MINDER MENU with the HDS.
14. Select RESETTING THE ATF with the HDS.
NOTE: If you changed the engine oil at the same
time with the ATF, select RESETTING THE ENGINE
OIL LIFE AND ATF with the HDS instead.
Replace.
08/08/21 14:46:53 61SNR030_140_0234
ProCarManuals.com
DYNOMITE -2009-

Î(#'

 )
21-721-7
A/C Refrigerant Oil Replacement
A
B C
3. Inspect the drive belt (see page 4-30).
4. Make sure no material is blocking the air flow to the
A/C condenser.
5. Check the dust and pollen filter. Replace it if it is clogged (see page 21-75).
6. Check for kinks or sharp bends in the A/C lines and hoses, which can greatly reduce system
performance. Replace A/C lines and hoses if they
are kinked or damaged (see page 21-8).
7. Start the engine, turn the air conditioning system on, and allow it to run for a few minutes and reach
stable operation.
 Check that the A/C operates at each position of the blower fan switch (except OFF). If the A/C
does not operate, refer to the symptom
troubleshooting.
 Check that the A/C compressor clutch (A) is engaged. The pressure plate should be rotating
at the same speed as the pulley. If the pressure
plate does not engage, refer to the symptom
troubleshooting.
 Check that the A/C condenser fan (B) and radiator fan (C) operate when the A/C compressor clutch
is engaged. If either fan fails to operate when the
A/C compressor clutch is engaged, refer to the
symptom troubleshooting.
 Check that the engine idle speed is correctly maintained when the A/C is switched on and off
and the A/C compressor clutch is engaged and
disengaged. Recommended PAG oil: SP-10
P/N 38897-P13-A01AH: 120 mL (4 fl·oz)
It is important to have the correct amount of refrigerant
oil in the A/C system to ensure proper lubrication of the
compressor. Too little oil damages the compressor; too
much oil reduces the cooling capacity of the system,
and can produce high vent temperatures.
 To avoid contamination, do not return the oil to the container once dispensed, and never mix it with other
refrigerant oils.
 Immediately after using the oil, reinstall the cap on the container, and seal it to avoid moisture
absorption.
 Do not spill the refrigerant oil on the vehicle; it may damage the paint; if it gets on the paint, wash it off
immediately.
Add the recommended refrigerant oil in the amount
listed if you replace any of the following parts: ........
.............. ............ ........
..............
........
.............. ............ ........
..............
A/C condenser .50 mL (1 2/3 fl·oz)
Evaporator .40 mL (1 1/3 fl·oz)
Line or hose .10 mL (1/3 fl·oz)
Receiver/Dryer .10 mL (1/3 fl·oz)
Leakage repair .25 mL (5/6 fl·oz)
A/C compressor .Since the oil separator is
equipped inside the compressor
for this vehicle, oil drainage is
unnecessary at the time of
compressor replacement.
08/08/21 14:40:56 61SNR030_210_0008
ProCarManuals.com
DYNOMITE -2009-

Î(#'

 )
21-721-7
A/C Refrigerant Oil Replacement
A
B C
3. Inspect the drive belt (see page 4-30).
4. Make sure no material is blocking the air flow to the
A/C condenser.
5. Check the dust and pollen filter. Replace it if it is clogged (see page 21-75).
6. Check for kinks or sharp bends in the A/C lines and hoses, which can greatly reduce system
performance. Replace A/C lines and hoses if they
are kinked or damaged (see page 21-8).
7. Start the engine, turn the air conditioning system on, and allow it to run for a few minutes and reach
stable operation.
 Check that the A/C operates at each position of the blower fan switch (except OFF). If the A/C
does not operate, refer to the symptom
troubleshooting.
 Check that the A/C compressor clutch (A) is engaged. The pressure plate should be rotating
at the same speed as the pulley. If the pressure
plate does not engage, refer to the symptom
troubleshooting.
 Check that the A/C condenser fan (B) and radiator fan (C) operate when the A/C compressor clutch
is engaged. If either fan fails to operate when the
A/C compressor clutch is engaged, refer to the
symptom troubleshooting.
 Check that the engine idle speed is correctly maintained when the A/C is switched on and off
and the A/C compressor clutch is engaged and
disengaged. Recommended PAG oil: SP-10
P/N 38897-P13-A01AH: 120 mL (4 fl·oz)
It is important to have the correct amount of refrigerant
oil in the A/C system to ensure proper lubrication of the
compressor. Too little oil damages the compressor; too
much oil reduces the cooling capacity of the system,
and can produce high vent temperatures.
 To avoid contamination, do not return the oil to the container once dispensed, and never mix it with other
refrigerant oils.
 Immediately after using the oil, reinstall the cap on the container, and seal it to avoid moisture
absorption.
 Do not spill the refrigerant oil on the vehicle; it may damage the paint; if it gets on the paint, wash it off
immediately.
Add the recommended refrigerant oil in the amount
listed if you replace any of the following parts: ........
.............. ............ ........
..............
........
.............. ............ ........
..............
A/C condenser .50 mL (1 2/3 fl·oz)
Evaporator .40 mL (1 1/3 fl·oz)
Line or hose .10 mL (1/3 fl·oz)
Receiver/Dryer .10 mL (1/3 fl·oz)
Leakage repair .25 mL (5/6 fl·oz)
A/C compressor .Since the oil separator is
equipped inside the compressor
for this vehicle, oil drainage is
unnecessary at the time of
compressor replacement.
08/08/21 14:40:56 61SNR030_210_0008
ProCarManuals.com
DYNOMITE -2009-

µ
Î
(#'


 )Refrigerant Capacity:
400 to 450 g
0.40 to 0.45 kg
0.9 to 1.0 lbs
14.1 to 15.9 oz
21-92
Climate Control
System Charging
A
C B
 Air conditioning refrigerant or lubricant vaporcan irritate your eyes, nose, or throat.
 Be careful when connecting service equipment.
 Do not breathe refrigerant or vapor.
NOTE:  If accidental system discharge occurs, ventilate the work area before resuming service.
 Additional health and safety information may be obtained from the refrigerant and lubricant
manufacturers.
1. Connect an R-134a refrigerant recovery/recycling/ charging station (A) to the high-pressure service
port (B) and the low-pressure service port (C), as
shown, following the equipment manufacturer’s
instructions. 2. Recover the refrigerant in the A/C system (see page
21-90).
3. Evacuate the system (see page 21-91). If the system cannot reach a vacuum of 93.3 kPa (700 mmHg,
27.6 in.Hg) in 15 minutes, or cannot hold a vacuum
for at least 15 minutes, there is probably a leak. Do
the Refrigerant Leak Check (see page 21-93), and
repair any leaks before charging the system.
4. Add the same amount of new refrigerant oil to the system that was removed during recovery. Use
only SP-10 refrigerant oil.
5. Charge the system with the specified amount of R-134a refrigerant. Do not overcharge the system;
the A/C compressor will be damaged.
Select the appropriate units of measure for your
refrigerant charging station.
6. Check for refrigerant leaks (see page 21-93).
7. Check the system performance (see page 21-99).
08/08/21 14:44:53 61SNR030_210_0093
ProCarManuals.com
DYNOMITE -2009-