2006 ACURA CSX automatic transmission fluid

µµµ
µ µµ
µ µµ
µ µµ
µ µµ
µ µµ µ
µ µ •••
µ µ •••
µ µ •••
µ µ •••
•••
µµ
(#'
#)
Automatic Transmission and A/T Differential
Item Measurement QualificationStandard or New Service Limit
2-12Standards and Service Limits
Automatic
transmission
fluid
Capacity
Use Acura ATF-Z1
Fluid change 2.9 L (3.1 US qt)
Overhaul 6.5 L (6.9 US qt)
ATF pressure Line pressure At 2,000 rpm in P or N900 960 kPa
(9.2 9.8 kgf/cm , 130 140 psi) 850 kPa
(8.7 kgf/cm , 120 psi)
1st clutch pressure At 2,000 rpm in 1st gear in S890 970 kPa
(9.1 9.9 kgf/cm , 130 140 psi) 840 kPa
(8.6 kgf/cm , 120 psi)
2nd clutch pressure At 2,000 rpm in 2nd gear in S890 970 kPa
(9.1 9.9 kgf/cm , 130 140 psi) 840 kPa
(8.6 kgf/cm , 120 psi)
3rd clutch pressure At 2,000 rpm in 3rd gear in S890 970 kPa
(9.1 9.9 kgf/cm , 130 140 psi) 840 kPa
(8.6 kgf/cm , 120 psi)
4th clutch pressure At 2,000 rpm in 4th gear in S890 970 kPa
(9.1 9.9 kgf/cm , 130 140 psi) 840 kPa
(8.6 kgf/cm , 120 psi)
5th clutch pressure At 2,000 rpm in 5th gear in S890 970 kPa
(9.1 9.9 kgf/cm , 130 140 psi) 840 kPa
(8.6 kgf/cm , 120 psi)
Torque converter Stall speed Check with vehicle on level ground 2,150 rpm 2,000 2,300 rpm
Clutch Clearance between clutch end-plate and top disc 1st 1.23 1.43 mm (0.048 0.056 in.)
2nd 0.75 0.95 mm (0.030 0.037 in.)
3rd 0.83 1.03 mm (0.033 0.041 in.)
4th, 5th 0.73 0.93 mm (0.029 0.037 in.)
Clutch return spring free length 1st, 2nd, 3rd 50.8 mm (2.00 in.) 48.8 mm (1.92 in.) 4th, 5th 33.5 mm (1.32 in.) 31.5 mm (1.24 in.)
Clutch disc thickness 1.94 mm (0.076 in.)
Clutch plate thickness 1st, 2nd, 3rd 2.0 mm (0.079 in.) When discolored 4th, 5th 2.3 mm (0.091 in.) When discolored
Clutch wave-plate phase difference 0.07 0.20 mm (0.003 0.008 in.) 0.05 mm (0.002 in.)
1st, 3rd clutch end-plate thickness Mark 1 2.3 mm (0.091 in.) When discolored Mark 2 2.4 mm (0.094 in.) When discolored
Mark 3 2.5 mm (0.098 in.) When discolored
Mark 4 2.6 mm (0.102 in.) When discolored
Mark 5 2.7 mm (0.106 in.) When discolored
Mark 6 2.8 mm (0.110 in.) When discolored
Mark 7 2.9 mm (0.114 in.) When discolored
Mark 8 3.0 mm (0.118 in.) When discolored
Mark 9 3.1 mm (0.122 in.) When discolored
Mark 10 3.2 mm (0.126 in.) When discolored
Mark 11 3.3 mm (0.130 in.) When discolored
Mark 12 3.4 mm (0.134 in.) When discolored
2nd clutch end-plate thickness Mark 1 2.6 mm (0.102 in.) When discolored Mark 2 2.7 mm (0.106 in.) When discolored
Mark 3 2.8 mm (0.110 in.) When discolored
Mark 4 2.9 mm (0.114 in.) When discolored
Mark 5 3.0 mm (0.118 in.) When discolored
Mark 6 3.1 mm (0.122 in.) When discolored
Mark 7 3.2 mm (0.126 in.) When discolored
Mark 8 3.3 mm (0.130 in.) When discolored
Mark 9 3.4 mm (0.134 in.) When discolored
2 2
2 2
2 2
2 2
2 2
2 2
08/08/21 14:07:16 61SNR030_020_0012
ProCarManuals.com
DYNOMITE -2009-


(#')
Application Lubricant or Fluid
3-2Lubricants and Fluids
API CERTIFICATION SEAL
For details of the lubrication points and the type of lubricants to be applied, refer to the illustrated index and the various work procedures (such
as Assembly/Reassembly, Replacement, Overhaul, Installation, etc.) contained in each section.


A Engine Acura Motor Oil:
K20Z2: P/N CA66808 (5W-20)
K20Z3: P/N CA66807 (5W-30)
Look for the API certification seal on the oil container. Make sure it says ‘‘For
Gasoline Engines.’’ SAE viscosity: See chart.
B Manual transmission Acura Manual Transmission Fluid (MTF): P/N 08798-9033C Always use Acura MTF. Using motor oil can cause stiffer shifting because it
does not contain the proper additives.
Automatic transmission Acura Automatic Transmission Fluid (ATF-Z1): P/N CA66704 Always use Acura ATF-Z1. Using a non-Acura ATF can affect shift quality.
C
D Brake system (including VSA lines)
Clutch system (manual transmission) Honda DOT 3 Brake Fluid: P/N 08798-9008
Always use Honda DOT 3 Brake Fluid. Using a non-Honda brake fluid can
cause corrosion and decrease the life of the system.
E F
G H I
J
K Brake booster clevis pin
Clutch master cylinder clevis pin (manual
transmission)
Release fork (manual transmission)
Battery terminals
Fuel fill door
Trunk hinges
Hood hinges and hood latch Multipurpose Grease
L
M Shift cable ends (manual transmission)
Caliper piston seal and boot, caliper pins and boots Honda Silicone Grease: P/N 08C30-B0234M
N Air conditioning compressor Compressor Oil: SP-10 (P/N 38897-P13-A01AH) for refrigerant HFC-134a (R-134a)
O Cooling system Honda Long Life Antifreeze/Coolant Type 2: P/N CA66688
08/08/21 14:08:29 61SNR030_030_0002
ProCarManuals.com
DYNOMITE -2009-


(#')
Information Display
Driver’s Side Dashboard:
3-4Maintenance Minder
General Information
MAINTENANCE MINDER INDICATOR
INFORMATION DISPLAY
SEL/RESET BUTTON
The maintenance minder is an important feature of the information display. Based on engine and transmission
operating conditions, the Acura CSX’s onboard computer (ECM/PCM) calculates the remaining engine oil and the
automatic transmission fluid life. The system also displays the remaining engine oil life along with the code(s) for
other scheduled maintenance items needing service.
08/08/21 14:08:30 61SNR030_030_0004
ProCarManuals.com
DYNOMITE -2009-

(#')Symbol Maintenance Main Items
3-7
Maintenance Main Items
If the message ‘‘SERVICE’’ does not appear more than 12 months after the display is reset, change the engine oil every
year.
NOTE:


 Replace the brake fluid every 3 years independent of the maintenance messages in the information display.
Inspect idle speed every 160,000 miles (256,000 km).
Adjust the valves during services A, B, 1, 2 or 3, only if they are noisy.

















A Replace engine oil (see page 8-10).
Engine oil capacity without oil filter:
K20Z2: 4.0 L (4.2 US qt)
K20Z3: 4.2 L (4.4 US qt)
B Replace engine oil and oil filter (see page 8-11). Engine oil capacity with oil filter:
K20Z2: 4.2 L (4.4 US qt)
K20Z3: 4.4 L (4.6 US qt)
Check front and rear brakes (see page 19-3). Check pad and disc for wear (thickness), damage, and cracks.
Check calipers for damage, leaks, and tightness of mounting bolts.
Check parking brake adjustment (see page 19-7). Check the number of clicks (8 to 10) when the parking brake lever is pulled with 196 N (20 kgf,
44 lbf) of force.
Inspect tie-rod ends, steering gearbox, and gearbox boots (see page 17-5). Check steering linkage.
Check boots for damage and leaking grease.
Check fluid lines for damage and leaks.
Inspect suspension components (see page 18-3). Check bolts for tightness.
Check condition of ball joint boots for deterioration and damage.
Inspect driveshaft boots (see page 16-4). Check boots for cracks and boot bands for tightness.
Inspect brake hoses and lines including VSA lines (see page 19-37). Check the master cylinder and VSA modulator-control unit for damage or leakage.
Inspect all fluid levels and condition of fluids. Engine coolant (see page 10-7)
Automatic transmission fluid (ATF-Z1) (see page 14-231)
Manual transmission fluid (MTF)
5M/T (see page 13-5), 6M/T (see page 13-82)
Clutch fluid (see page 12-7)
Brake fluid (see page 19-9)
Windshield washer fluid (see page 22-234)
Inspect exhaust system: K20Z2 (see page 9-13), K20Z3 (see page 9-14)
Check catalytic converter heat shields, exhaust pipes, and muffler for damage, leaks, and tightness.
Inspect fuel lines (see page 11-326) and connections (see page 11-328). Check for loose connections, cra cks, and deterioration; retighten loose connections and replace
damaged parts.
NOTE: According to state and federal regulations, failure to do the maintenance items marked with an asterisk ( ) will
not void the client’s emissions warranties. However, Acura recommends that all maintenance services be done at the
recommended interval, to ensure long-term reliability.
08/08/21 14:08:32 61SNR030_030_0007
ProCarManuals.com
DYNOMITE -2009-

µµ µµ
µµ µµ
(#')
Number Maintenance Sub Items
3-8
Maintenance Minder
Maintenance Sub Items
1 Rotate tires, and check tire inflation and condition.
Follow the pattern shown in the Owner’s Manual.


2 Replace air cleaner element (see page 11-346).
Replace every 15,000 miles (24,000 km) if the vehicle is driven in dusty conditions.
Replace dust and pollen filter (see page 21-75). If the vehicle is driven mostly in urban areas that have high concentrations of dust, pollen, or soot in
the air, replace every 15,000 miles (24,000 km).
Replace the filter whenever airflow from the heating and air c onditioning system is less than normal.
Inspect drive belt (see page 4-30). Look for cracks and damage, then check the position of the drive belt auto-tensioner indicator.
3 Replace automatic transmission fluid (see page 14-232). Capacity:2.9L(3.1USqt);useAcuraATF-Z1.
Replace manual transmission fluid. 5M/T (see page 13-5), 6M/T (see page 13-82)
Capacity:1.5L(1.6USqt);useAcuraMTF.




4 Replace spark plugs (see page 4-21).
K20Z2: Use SKJ20DR-M11 (DENSO).
K20Z3: Use SK22PR-M11S (DENSO).
Inspect valve clearance (cold). K20Z2 (see page 6-12)
Intake: 0.21 0.25 mm (0.008 0.010 in.), Exhaust: 0.28 0.32 mm (0.011 0.013 in.)
K20Z3 (see page 6-14)
Intake: 0.21 0.25 mm (0.008 0.010 in.), Exhaust: 0.25 0.29 mm (0.010 0.011 in.)


5 Replace engine coolant (see page 10-8).
Capacity (including the reservoir):
K20Z2: M/T 4.3 L (1.14 US gal), A/T 4.2 L (1.11 US gal)
K20Z3: 4.5 L (1.19 US gal)
Use Honda Long Life Antifreeze/Coolant Type 2.
08/08/21 14:08:32 61SNR030_030_0008
ProCarManuals.com
DYNOMITE -2009-






5-6Engine Assembly
Engine Removal (cont’d)
C
B
D
A B
C
A
D
D A
B
C
27. Drain the engine oil (see page 8-10).
28. Drain the transmission fluid: Manual transmission (see step 3 on page 13-5)
 Automatic transmission (see step 3 on page14-232)
29. Disconnect the air fuel ratio (A/F) sensor connector (A).
30. Remove the grommet (B), then disconnect the secondary heated oxygen sensor (secondary
HO2S) connector (C).
31. Remove the three way catalytic converter (TWC) (D).
32. A/T model: Remove the shift cable. Do not bend the cables excessively (see step 39 on page 14-239).
33. Separate the stabilizer links (see page 18-25).
34. Separate the knuckles from the lower arms (see step 6 on page 18-21).
35. Remove the driveshafts (see page 16-4). Coat all precision-finished surfaces with new engine oil. Tie
plastic bags over the driveshaft ends. 36. Remove the steering gearbox bracket (A).
37. Remove the steering gearbox mounting bolt (B),
the stiffener mounting bolt (C), and the stiffener (D).
38. Remove the steering gearbox mounting bolt (A), the stiffener mounting bolt (B), and the stiffener (C).
39. Remove the harness clamp (D) from the subframe.
08/08/21 14:20:24 61SNR030_050_0006
ProCarManuals.com
DYNOMITE -2009-







5-7
A
B VSB02C000015
40. Disconnect the A/C compressor clutch connector(A), then remove the A/C compressor (B) without
disconnecting the A/C hoses.
41. Lower the vehicle on the lift.
42. Remove the radiator (see page 10-19).
43. A/T model: Disconnect the automatic transmission fluid (ATF) cooler hoses from the transmission,
then plug the lines and hoses. 44. Disconnect the heater hoses.
45. Install the bulkhead (see step 13 on page 10-21).
46. Attach the engine hanger adapter (VSB02C000015)
to the threaded hole in the cylinder head.
(cont’d)
08/08/21 14:20:25 61SNR030_050_0007
ProCarManuals.com
DYNOMITE -2009-


Î

5-21
A AB
B 6x1.0mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A B
41. Lower the vehicle on the lift.
42. Connect the heater hoses.
43. A/T model: Connect the automatic transmissionfluid (ATF) cooler hoses (A) to the transmission,
and secure the hoses with the clips (B) (see page
14-253).
44. Remove the bulkhead, then install the radiator (see page 10-19).
45. Install the idler pulley base (see step 2 on page 4-34).
46. Install the drive belt (see page 4-31). 47. M/T model: Install the air cleaner bracket.
48. M/T model: Install the shift cables (see step 37 on
page 13-20).
49. M/T model: Install the clutch slave cylinder and the clutch line bracket mounting bolt (see step 40 on
page 13-21).
50. Connect the fuel feed hose (A) (see page 11-331), then install the quick-connect fitting cover (B).
(cont’d)
08/08/21 14:20:59 61SNR030_050_0021
ProCarManuals.com
DYNOMITE -2009-