Page 1697 of 2893

(#'
)
20-23
Rear Door Glass and Regulator Replacement
A
B C
FG
H
E
C
E
D
Fastener Locations :Bolt,2
6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)A
B
A
C Fastener Locations
:Bolt,1
A:Screw,1 D
4x0.7mm
4N·m
(0.4 kgf·m, 3 lbf·ft)
6x1.0mm
8N·m
(0.8 kgf·m, 6 lbf·ft) A
B C
D
NOTE: Put on gloves to protect your hands.
1. Remove the door panel (see page 20-17).
2. Detach the harness clip (A), and disconnect the power door lock actuator connector (B). Remove
the plug caps (C).
3. Pass the cable (D) and the harnesses (E) through the holes (F) and slit (G) in the plastic cover (H),
then remove it.
4. Carefully move the glass (A) until you can see the bolts, then remove them. Release the glass from
the holder (B), then remove it from the regulator (C),
and carefully lower the glass. Take care not to drop
the glass inside the door. 5. Remove the bolt (A) from the rear lower channel (B).
Pull the glass run channel (C) away as needed, and
remove the screw (D).
(cont’d)
08/08/21 14:59:08 61SNR030_200_0025
ProCarManuals.com
DYNOMITE -2009-
Page 1698 of 2893
20-24
Doors
Rear Door Glass and Regulator Replacement (cont’d)
A
B C
D
E
B
A B A
A A
B
B
A
6. Pull the glass run channel (A) away as needed. Pull
the rear lower channel (B) forward from the quarter
glass seal (C) then release the upper hook (D) from
the door. Remove the rear lower channel from the
rear door glass (E), then pull the channel up to
remove it.
7. Remove the rear lower channel (A) from the glass run channel (B). 8. Carefully remove the glass (A) out through the
window slot. Take care not to drop the glass inside
the door.
9. Remove the quarter glass (A). Take care not to damage the outer weatherstrip (B).
08/08/21 14:59:09 61SNR030_200_0026
ProCarManuals.com
DYNOMITE -2009-
Page 1699 of 2893

20-25
6x1.0mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
(Black)
Fastener Locations
:Bolt,4
C:Bolt,1 D
(Gold)
CCC A
B C
D 6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
AA
10. Disconnect the connector (A) from the regulator (B).
11. Remove the bolts (C), and loosen the bolt (D), then
remove the regulator through the hole in the door. 12. Grease all the sliding surfaces of the regulator (A)
where shown.
13. Install the glass and regulator in the reverse order of removal, and note these items:
Roll the glass up and down to verify if it moves freely without binding.
Make sure that there is no clearance between the glass and glass run channel when the glass is
closed.
Adjust the position of the glass as necessary (see page 20-28).
When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
Check for water leaks (see step 9 on page 20-29).
08/08/21 14:59:09 61SNR030_200_0027
ProCarManuals.com
DYNOMITE -2009-
Page 1700 of 2893
(#'
)
20-26 Doors
Rear Door Glass Outer Weatherstrip Replacement
A
B
A
A B
NOTE:
Put on gloves to protect your hands.
Take care not to scratch the door.
1. Remove these items: Door panel (see page 20-17)
Plastic cover (see step 4 on page 20-19)
Rear door glass (see page 20-23)
Quarter glass (see step 9 on page 20-24)
2. Release the front hook (A) from inside of the door, then pull up the front portion of the rear door glass
outer weatherstrip (B). 3. Starting at the front, slowly pull up the rear door
glass outer weatherstrip (A).
4. Push the rear hook (A) out from inside of the door, then remove the rear door glass outer weatherstrip
(B).
5. Push the clip portions of the rear door glass outer weatherstrip into place securely.
08/08/21 14:59:10 61SNR030_200_0028
ProCarManuals.com
DYNOMITE -2009-
Page 1701 of 2893

(#'
)
20-27
Rear Door Weatherstrip Replacement
Fastener Locations:Bolt,1
A :Clip,13
B
B A B
C
D F
E C
E
E
E
8x1.25mm
29 N·m
(3.0 kgf·m, 22 lbf·ft) : Clip, 2
C
:Clip,1
D (White)
(Black) (Left: Yellow
Right: Green)
NOTE:
Put on gloves to protect your hands.
Take care not to scratch the door.
Remove the clips with a clip remover.
1. At the B-pillar, remove the door checker mounting
bolt (A).
2. Detach the clips (B, C, D), then remove the door weatherstrip (E). 3. Install the weatherstrip in the reverse order of
removal, and note these items:
If the clips are damaged or stress-whitened, replace them with new ones.
Make sure the weatherstrip is installed in the holder (F) securely.
Apply medium strength liquid thread lock to the door checker mounting bolt before installation.
When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
Check for water leaks (see step 9 on page 20-29).
08/08/21 14:59:10 61SNR030_200_0029
ProCarManuals.com
DYNOMITE -2009-
Page 1702 of 2893
(#'
")
Front
Rear
20-28Doors
Front and Rear Door Glass Adjustment
B
6x1.0mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
C A
B
6x1.0mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
C A
A
B
NOTE: Check the weatherstrip and glass run channel for
damage or deterioration, and replace them if necessary. 1. Place the vehicle on a firm, level surface.
2. Remove these items: Door panel:– Front door (see page 20-7)
– Rear door (see page 20-17)
Plastic cover: – Front door (see step 4 on page 20-9)
– Rear door (see step 4 on page 20-19)
3. Carefully move the glass (A) until you can see the glass mounting bolts (B), then loosen them.
4. Push the glass against the channel (C), then tightenthe glass mounting bolts.
5. Check that the glass moves smoothly.
6. Raise the glass fully, and check for gaps. Also make sure that the glass (A) contacts the glass run
channel (B) evenly.
08/08/21 14:59:11 61SNR030_200_0030
ProCarManuals.com
DYNOMITE -2009-
Page 1703 of 2893

(#'
") Front door
20-2920-29
Front and Rear Door Position
Adjustment
12 mm (0.47 in.)
0.5m(19in.)
300 mm (12 in.) B
C
A
D
8x1.25mm
29 N·m
(3.0 kgf·m,
22 lbf·ft)
F
8x1.25mm
29 N·m
(3.0 kgf·m,
22 lbf·ft)
A
B C
7. Attach the plastic cover making sure it its sealed
around its outside perimeter to seal out water.
8. Reinstall the door panel: Front door (see page 20-9)
Rear door (see page 20-19)
9. Check for water leaks. Run water over the roof and on the sealing area as shown, and note these items:
Use a 12 mm (0.47 in.) diameter hose (A).
Adjust the rate of water flow as shown (B).
Do not use a nozzle.
Hold the hose about 300 mm (12 in.) away from the door (C). NOTE: Check for a flush fit with the body, then check for
equal gaps between the front, rear, and bottom door
edges and the body. Check that the door and the body
edges are parallel. If necessary, replace the mounting
bolts before adjusting the door position.
1. Place the vehicle on a firm, level surface when adjusting the doors.
2. Adjust at the hinges (A): Pad a floor jack (B) with shop towels (C), then usethe jack to support the door to prevent damage to
the door while adjusting it.
On the front door: Remove the front inner fender (see page 20-171). Loosen the hinge m ounting
bolts (D) slightly, and move the door backward or
forward, up or down as necessary to equalize the
gaps.
On the rear door: Loosen the hinge mounting bolts (E) slightly, and move the door backward or
forward, up or down as necessary to equalize the
gaps.
(cont’d)
08/08/21 15:00:01 61SNR030_200_0031
ProCarManuals.com
DYNOMITE -2009-
Page 1704 of 2893

(#'
") Front door
20-2920-29
Front and Rear Door Position
Adjustment
12 mm (0.47 in.)
0.5m(19in.)
300 mm (12 in.) B
C
A
D
8x1.25mm
29 N·m
(3.0 kgf·m,
22 lbf·ft)
F
8x1.25mm
29 N·m
(3.0 kgf·m,
22 lbf·ft)
A
B C
7. Attach the plastic cover making sure it its sealed
around its outside perimeter to seal out water.
8. Reinstall the door panel: Front door (see page 20-9)
Rear door (see page 20-19)
9. Check for water leaks. Run water over the roof and on the sealing area as shown, and note these items:
Use a 12 mm (0.47 in.) diameter hose (A).
Adjust the rate of water flow as shown (B).
Do not use a nozzle.
Hold the hose about 300 mm (12 in.) away from the door (C). NOTE: Check for a flush fit with the body, then check for
equal gaps between the front, rear, and bottom door
edges and the body. Check that the door and the body
edges are parallel. If necessary, replace the mounting
bolts before adjusting the door position.
1. Place the vehicle on a firm, level surface when adjusting the doors.
2. Adjust at the hinges (A): Pad a floor jack (B) with shop towels (C), then usethe jack to support the door to prevent damage to
the door while adjusting it.
On the front door: Remove the front inner fender (see page 20-171). Loosen the hinge m ounting
bolts (D) slightly, and move the door backward or
forward, up or down as necessary to equalize the
gaps.
On the rear door: Loosen the hinge mounting bolts (E) slightly, and move the door backward or
forward, up or down as necessary to equalize the
gaps.
(cont’d)
08/08/21 15:00:01 61SNR030_200_0031
ProCarManuals.com
DYNOMITE -2009-