2006 ACURA CSX Service Repair Manual

ESP buttons CD player keyless entry air bleeding technical data

Page 1097 of 2893

ACURA CSX 2006 Service Repair Manual µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
14-181
14. Inspect shift solenoid valve D and the shift solenoid
wire harness (see page 14-215).
15. Replace either shift solenoid valve D o

µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
14-181
14. Inspect shift solenoid valve D and the shift solenoid
wire harness (see page 14-215).
15. Replace either shift solenoid valve D or the shift solenoid wire harness (see page 14-217),
whichever failed the test, then go to step 16.
16. Reconnect all connectors.
17. Turn the ignition switch to ON (II).
18. Clear the DTC with the HDS.
19. Start the engine with the shift lever in P, and wait for at least 1 second. Then test-drive the vehicle in
2nd gear in D for at least 1 second.
20. Check for Temporary DTCs or DTCs with the HDS.
Check for intermittent short to body ground
in the wire between shift solenoid valve D and the
PCM, then go to step 1.
Go to step 21.
21. Monitor the OBD STATUS for P0982 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 20,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for
intermittent short to body ground in the wire
between shift solenoid valve D and the PCM, then
go to step 1. If the HDS indicates NOT COMPLETED,
go to step 19. 22. Reconnect all connectors.
23. Update the PCM if it does not have the latest
software (see page 11-227), or substitute a known-
good PCM (see page 11-7).
24. Start the engine with the shift lever in P, and wait for at least 1 second. Then test-drive the vehicle in
2nd gear in D for at least 1 second.
25. Check for Temporary DTCs or DTCs with the HDS.
Check for intermittent short to body ground
in the wire between shift solenoid valve D and the
PCM. If the PCM was updated, substitute a known-
good PCM (see page 11-7), then go to step 24. If the
PCM was substituted, go to step 1.
Go to step 26.
26. Monitor the OBD STATUS for P0982 in the DTCs MENU with the HDS.
If the PCM was updated, troubleshooting is
complete. If the PCM was substituted, replace the
original PCM (see page 11-228). If any other
Temporary DTCs or DTCs were indicated in step 25,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for
intermittent short to body ground in the wire
between shift solenoid valve D and the PCM. If the
PCM was updated, substitute a known-good PCM
(see page 11-7), then go to step 24. If the PCM was
substituted, go to step 1. If the HDS indicates NOT
COMPLETED, go to step 24.
I s DT C P0982 i nd i cat ed ?
Does the HDS ind icate PASSED? I s DT C P0982 i nd i cat ed ?
Does the HDS ind icate PASSED?
08/08/21 14:45:25 61SNR030_140_0183
ProCarManuals.com
DYNOMITE -2009-

Page 1098 of 2893

ACURA CSX 2006 Service Repair Manual µ
Î
(#

)
µ
µ
µ
µ
µ
µ µ
µ
DTC P0983:
YES
NO
YES
NO
YES
NO YES
NO
14-182Automatic Transmission
DTC Troubleshooting (cont’d)
PCM CO

Page 1099 of 2893

ACURA CSX 2006 Service Repair Manual ÎÎ
µ
µ µ
µ
YES
NO
YES
NO
14-183
PCM CONNECTOR B (44P)
SHD
(GRN/RED)
SHIFT SOLENOID WIRE
HARNESS CONNECTOR
SHD (GRN/RED) SHIFT SOLENOID WIRE
HARNESS CONNECTOR
SHIFT SOLENOID
VALVE D

Page 1100 of 2893

ACURA CSX 2006 Service Repair Manual µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
14-184Automatic Transmission
DTC Troubleshooting (cont’d)
16. Reconnect all connectors.
17. Turn the ignition switch to ON (II).
18. Clear

µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
14-184Automatic Transmission
DTC Troubleshooting (cont’d)
16. Reconnect all connectors.
17. Turn the ignition switch to ON (II).
18. Clear the DTC with the HDS.
19. Start the engine with the shift lever in P, and wait
for at least 1 second. Then test-drive the vehicle in
2nd gear in D for at least 1 second.
20. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals between shift solenoid valve D and the
PCM, then go to step 1.
Go to step 21.
21. Monitor the OBD STATUS for P0983 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 20,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for poor
connections or loose terminals between shift
solenoidvalveDandthePCM,thengotostep1.If
the HDS indicates NOT COMPLETED, go to step 19. 22. Reconnect all connectors.
23. Update the PCM if it does not have the latest
software (see page 11-227), or substitute a known-
good PCM (see page 11-7).
24. Start the engine with the shift lever in P, and wait for at least 1 second. Then test-drive the vehicle in
2nd gear in D for at least 1 second.
25. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals between shift solenoid valve D and the
PCM. If the PCM was updated, substitute a known-
good PCM (see page 11-7), then go to step 24. If the
PCM was substituted, go to step 1.
Go to step 26.
26. Monitor the OBD STATUS for P0983 in the DTCs MENU with the HDS.
If the PCM was updated, troubleshooting is
complete. If the PCM was substituted, replace the
original PCM (see page 11-228). If any other
Temporary DTCs or DTCs were indicated in step 25,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for poor
connections or loose terminals between shift
solenoid valve D and the PCM. If the PCM was
updated, substitute a known-good PCM (see page
11-7), then go to step 24. If the PCM was substituted,
go to step 1. If the HDS indicates NOT COMPLETED,
go to step 24.
I s DT C P0983 i nd i cat ed ?
Does the HDS ind icate PASSED? I s DT C P0983 i nd i cat ed ?
Does the HDS ind icate PASSED?
08/08/21 14:45:26 61SNR030_140_0186
ProCarManuals.com
DYNOMITE -2009-

Page 1101 of 2893

ACURA CSX 2006 Service Repair Manual Î
Î
(#
)
µ
µ µ
µ
µ
µ
DTC P0985:
’06 Model
YES
NO YES
NO
YES
NO
14-185
PCM CONNECTORS
B (44P) C (44P)
LG1 (BRN/YEL)
SHE (YEL)
PCM

Page 1102 of 2893

ACURA CSX 2006 Service Repair Manual µ
µ µ
µ
YES
NO YES
NO
14-186Automatic Transmission
DTC Troubleshooting (cont’d)
11. Inspect shift solenoid valve E and the shift solenoid
harness (see page 14-215).
12. Replace either shift

Page 1103 of 2893

ACURA CSX 2006 Service Repair Manual Î
Î
(#
)
µ
µ
µ
µ
µ
µ µ
µ
µ
µ
DTC P0985:
’07-09 Models
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
14-187
PCM CONNECTORS
B(44P) C(

Î
Î
(#'
)
µ
µ
µ
µ
µ
µ µ
µ
µ
µ
DTC P0985:
’07-09 Models
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
14-187
PCM CONNECTORS
B(44P) C(44P)
LG1 (BRN/YEL)
SHE (YEL)
PCM CONNECTORS
B(44P) C(44P)
LG1 (BRN/YEL)
SHE (YEL)
Short in Shift Solenoid Valve E
Circuit
NOTE:
Before you troubleshoot, record all freeze data and any on-board snapshot with the HDS, and review
General Troubleshooting Information (see page 14-3).
This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the
transmission.
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine with the shift lever in P, and wait for at least 1 second.
4. Check for Temporary DTCs or DTCs with the HDS.
Go to step 8.
Go to step 5.
5. Select Shift Solenoid Valve E in the Miscellaneous Test Menu, and test shift solenoid valve E with the
HDS.
Go to step 6.
Go to step 8.
6. Start the engine with the shift lever in P, and wait for at least 1 second.
7. Monitor the OBD STATUS for P0985 in the DTCs MENU with the HDS.
Go to step 8.
If the HDS indicates PASSED, intermittent
failure, the system is OK at this time. Check for
intermittent short to body ground in the wire
between shift solenoid valve E and the PCM. If the
HDS indicates NOT COMPLETED, go to step 5. 8. Turn the ignition switch to LOCK (0).
9. Jump the SCS line with the HDS.
10. Disconnect PCM connectors B (44P) and C (44P).
11. Measure the resistance between PCM connector terminals B24 and C40.
Go to step 12.
Go to step 22.
12. Disconnect the shift solenoid wire harness connector.
13. Check for continuity between PCM connector terminals B24 and C40.
Repair short to body ground in the wire
between PCM connector terminal B24 and the shift
solenoid wire harness connector, then go to step
16.
Go to step 14.
(cont’d)
Terminal side of female terminals
Terminal side of female terminals
I s DT C P0985 i nd i cat ed ?
Is a clicking sound heard?
Does the HDS ind icate F AILED? Is t her e l ess t han 12 ?
Is there continuity?
08/08/21 14:45:27 61SNR030_140_0189
ProCarManuals.com
DYNOMITE -2009-

Page 1104 of 2893

ACURA CSX 2006 Service Repair Manual µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
14-188Automatic Transmission
DTC Troubleshooting (cont’d)
14. Inspect shift solenoid valve E and the shift solenoid
wire harness (see page

µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
14-188Automatic Transmission
DTC Troubleshooting (cont’d)
14. Inspect shift solenoid valve E and the shift solenoid
wire harness (see page 14-215).
15. Replace either shift solenoid valve E or the shift solenoid wire harness (see page 14-217),
whichever failed the test, then go to step 16.
16. Reconnect all connectors.
17. Turn the ignition switch to ON (II).
18. Clear the DTC with the HDS.
19. Start the engine with the shift lever in P, and wait for at least 1 second. Then shift to N, and wait for at
least 1 second.
20. Check for Temporary DTCs or DTCs with the HDS.
Check for intermittent short to body ground
in the wire between shift solenoid valve E and the
PCM, then go to step 1.
Go to step 21.
21. Monitor the OBD STATUS for P0985 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 20,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for
intermittent short to body ground in the wire
between shift solenoid valve E and the PCM, then
go to step 1. If the HDS indicates NOT COMPLETED,
go to step 19. 22. Reconnect all connectors.
23. Update the PCM if it does not have the latest
software (see page 11-227), or substitute a known-
good PCM (see page 11-7).
24. Start the engine with the shift lever in P, and wait for at least 1 second. Then shift to N, and wait for at
least 1 second.
25. Check for Temporary DTCs or DTCs with the HDS.
Check for intermittent short to body ground
in the wire between shift solenoid valve E and the
PCM. If the PCM was updated, substitute a known-
good PCM (see page 11-7), then go to step 24. If the
PCM was substituted, go to step 1.
Go to step 26.
26. Monitor the OBD STATUS for P0985 in the DTCs MENU with the HDS.
If the PCM was updated, troubleshooting is
complete. If the PCM was substituted, replace the
original PCM (see page 11-228). If any other
Temporary DTCs or DTCs were indicated in step 25,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for
intermittent short to body ground in the wire
between shift solenoid valve E and the PCM. If the
PCM was updated, substitute a known-good PCM
(see page 11-7), then go to step 24. If the PCM was
substituted, go to step 1. If the HDS indicates NOT
COMPLETED, go to step 24.
I s DT C P0985 i nd i cat ed ?
Does the HDS ind icate PASSED? I s DT C P0985 i nd i cat ed ?
Does the HDS ind icate PASSED?
08/08/21 14:45:27 61SNR030_140_0190
ProCarManuals.com
DYNOMITE -2009-

Load next 8 pages

Page: < prev 1-10 ... 1065-1072 1073-1080 1081-1088 1089-1096 1097-1104 1105-1112 1113-1120 1121-1128 1129-1136 ... 2896 next >

fuse box service reset oil filter child seat oil temperature alarm