2006 ACURA CSX ECU




(#')
µ
Emergency Towing
Flat-bed Equipment
This is the best way of
transporting the vehicle.
Front: Rear:
1-12General Information
Towing
A
B D
C
If the vehicle needs to be towed, call a professional
towing service. Never tow the vehicle behind another
vehicle with a rope or chain. It is very dangerous.
There are three popular methods of towing a vehicle.
The operator loads the vehicle
on the back of a truck.
To accommodate flat-bed equipment, the vehicle is
equipped with front towing hooks (A), front tie down
hook slots (B), rear towing hook (C), and rear tie down
hook slots (D).
The rear towing hook can be used with a winch to pull
the vehicle onto the truck, and the tie down hook slots
can be used to secure the vehicle to the truck.
08/08/21 14:06:05 61SNR030_010_0012
ProCarManuals.com
DYNOMITE -2009-

Î
 Î
Î
Installation
4-11
A
B
A
BC B
CA 8x1.25mm
9 N·m (0.9 kgf·m, 7 lbf·ft)
10x1.25mm
44 N·m
(4.5 kgf·m, 33 lbf·ft) 10x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
A
4. Remove the harness clamp (A), then the two bolts(B) securing the starter, then remove the starter
from the engine.
5. Disconnect the positive starter cable (A) and the S terminal connector (B).
6. Remove the harness clamp (C), then remove the starter. 1. Install the harness clamp (A).
2. Connect the positive starter cable (B) and S
terminal connector (C). Make sure the starter cable
crimped side of the ring terminal faces away from
the starter when you connect it.
3. Install the starter, and tighten the two bolts, then install the harness clamp (A).
(cont’d)
08/08/21 14:09:25 61SNR030_040_0012
ProCarManuals.com
DYNOMITE -2009-

Î
Î

4-35
D
C
A
C B
B
C
A AB
C
5. Disconnect the reservoir hose (A), and remove the radiator cap base mounting bolts (B), the radiator
upper brackets (C) and the bolts (D).
6. Remove the A/C condenser bracket mounting bolts (A) and the bulkhead mounting bolts (B), then
remove the bulkhead (C). 7. Remove the three bolts securing the alternator.
8. Disconnect the alternator connector (A), and the
positive alternator cable (B) and remove the
harness clamp (C), then remove the alternator.
(cont’d)
08/08/21 14:10:15 61SNR030_040_0036
ProCarManuals.com
DYNOMITE -2009-


Î Î
Î
Installation
4-36Charging System
Alternator Removal and Installation (cont’d)
A
B
C 6x1.0mm
8 N·m (0.8 kgf·m,
6lbf·ft)
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft) 8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft) A
B
6x1.0mm
10 N·m (1.0 kgf·m, 7.2 lbf·ft)
C
6x1.0mm
10 N·m (1.0 kgf·m, 7.2 lbf·ft) A
D
A
C
6x1.0mm
10 N·m (1.0 kgf·m, 7.2 lbf·ft)
B
6x1.0mm
10 N·m (1.0 kgf·m, 7.2 lbf·ft)
1. Install the alternator, then connect the alternator
connector (A) and the positive alternator cable (B)
and install the harness clamp (C). Make sure the
crimped side of the ring terminal faces away from
the alternator when you connect it.
2. Tighten the three bolts securing the alternator. 3. Install the bulkhead (A), then install the bulkhead
mounting bolts (B) and the A/C condenser bracket
mounting bolts (C).
4. Apply body paint to the bulkhead mounting bolts.
5. Install the radiator upper brackets (A), the radiator cap base mounting bolts (B), and the bolts (C), and
connect the reservoir hose (D).
08/08/21 14:10:16 61SNR030_040_0037
ProCarManuals.com
DYNOMITE -2009-

ÌÏ

Î

(#'
 )
Special Tools Required
5-3
Engine Removal
C
A
B
B
AB
 Engine hanger adapter VSB02C000015
 Engine support hanger, A and Reds AAR-T 1256
 2006 Civic engine hanger VSB02C000025
 Front subframe adapter VSB02C000016
 Universal lifting eyelet 07AAK-SNAA120 : These special tools are available through Honda
Canada Inc. Technical Tools Department; FAX 866-398-8665/e-mail: ch_technicaltools ch.honda.
com
NOTE:  Use fender covers to avoid damaging painted surfaces.
 To avoid damaging the wire and terminals, unplug the wiring connectors carefully while holding the
connector portion.
 Mark all wiring and hoses to avoid misconnection. Also, be sure that they do not contact other wiring or
hoses, or interfere with other parts.
1. Secure the hood in the wide open position (support rod in the lower hole).
2. Relieve the fuel pressure (see page 11-322).
3. Do the battery removal procedure (see page 22-69).
4. Disconnect the vacuum hose and the breather pipe, then remove the intake air duct (see step 2 on page
9-3).
5. Remove the air cleaner assembly (see page 11-345).
6. Remove the under-cowl panel (see step 4 on page 20-164). 7. Disconnect the connector (A), and remove the
harness clamps (B), then remove the pipe (C).
8. Disconnect the battery cables (A) from the under- hood fuse/relay box.
9. Remove the harness clamp (B). (cont’d)
08/08/21 14:20:21 61SNR030_050_0003
ProCarManuals.com
DYNOMITE -2009-


Î 

5-4Engine Assembly
Engine Removal (cont’d)
A
B B
C A A
B
10. Remove the engine control module (ECM)/ powertrain control module (PCM) cover (A), then
remove the three bolts (B) securing the ECM/PCM.
11. Disconnect the ECM/PCM connectors (A) and the engine wire harness connector (B).
12. Remove the harness clamps (C). 13. Remove the under-hood fuse/relay box (A) from the
ECM/PCM bracket (B), then remove the ECM/PCM
bracket.
14. K20Z3 engine: Remove the engine cover.
08/08/21 14:20:22 61SNR030_050_0004
ProCarManuals.com
DYNOMITE -2009-


Î 
Î
5-9
A CC
A
BB A
VSB02C000016
A
C
D B
50. M/T model: Remove the front mount mounting bolt.
51. Make appropriate reference lines (A) at both sides
of the front subframe (B) that line up with the edges
(C) on the body. 52. Loosen the mid-stiffener mounting bolts (A) on
both sides.
53. Attach the front subframe adapter (VSB02C000016) to the subframe, and hang the belt (A) of the front
subframe adapter over the front of the subframe
(B). Secure the belt with its stop (C), then tighten
the wing nut (D).
54. Raise the jack, and line up the slots in the front subframe adapter arms with the bolt holes on the
jack base, then securely attach them with four bolts.
(cont’d)
Replace. Replace.
08/08/21 14:20:26 61SNR030_050_0009
ProCarManuals.com
DYNOMITE -2009-


Î 

5-11
07AAK-SNAA120
B
07AAK-SNAA120 A
A/T model
C
M/T model
60. Install the universal lifting eyelet (07AAK- SNAA120).
61. Attach a chain hoist (A) to the universal lifting eyelet (B) and the transmission hook (C), then lift
the engine/transmission until it’s securely
supported by the chain hoist, and remove the
engine hanger. 62. Remove the side engine mount bracket mounting
bolt and nut.
63. M/T model: Remove the transmission mount bracket mounting bolt and nuts.
(cont’d)
Replace.
Replace.
08/08/21 14:20:28 61SNR030_050_0011
ProCarManuals.com
DYNOMITE -2009-