2006 ACURA CSX parking brake




(#')
Vehicle Lift
Safety Stands Floor Jack
1-11
Lift and Support Points
A
B CC
C
B
A
NOTE: If you are going to remove heavy com
ponents
such as suspension or the fuel tank from the rear of the
vehicle, first support the front of the vehicle with tall
safety stands. When substantial weight is removed
from the rear of the vehicle, the center of gravity can
change, causing the vehicle to tip forward on the lift.
1. Position the lift blocks (A) under the vehicle’s front support points (B) and rear support points (C).
2. Raise the lift a few inches, and rock the vehicle gently to be sure it is firmly supported.
3. Raise the lift to its full height, and inspect the vehicle support points for solid contact with the lift
blocks.
To support the vehicle on safety stands, use the same
support points as for a vehicle lift. Always use safety
stands when working on or under any vehicle that is
supported only by a jack. 1. When lifting the front of the vehicle, set the parking
brake. When lifting the rear of the vehicle, put the
shift lever in reverse for manual transmission, or in
P for automatic transmission.
2. Block the wheels that are not being lifted.
3. Position the floor jack under the front jacking bracket (A) or the rear jacking bracket (B). Center
the jacking bracket on the jack lift platform (C), and
jack up the vehicle high enough to fit the safety
stands under it.
4. Position the safety stands under the support points, and adjust them so the vehicle is level.
5. Lower the vehicle onto the stands.
08/08/21 14:06:05 61SNR030_010_0011
ProCarManuals.com
DYNOMITE -2009-

µµ
Wheel Lift Equipment
This is an acceptable way of towing the
vehicle.
Sling-type Equipment
This method of towing
the vehicle is unacceptable.
Manual Transmission
Automatic Transmission
1-13
The tow truck uses two
pivoting arms that go under the tires (front or rear) and
lift them off the ground. The other two wheels remain
on the ground.
The tow truck uses metal
cables with hooks on the ends. These hooks go around
parts of the frame or the suspension, and the cables lift
that end of the vehicle off the ground. The vehicle’s
suspension and body can be seriously damaged if this
method of towing is attempted.
If the vehicle cannot be transported by a flat-bed, it
should be towed with the front wheels off the ground. If
the vehicle is damaged, and must be towed with the
front wheels on the ground, or with all four wheels on
the ground, do this:
 Release the parking brake.
 Shift the transmission to neutral.
 Leave the ignition switch in ACCESSORY (I) so the steering wheel does not lock.
 Make sure all accessories are turned off to minimize current battery draw.
 Release the parking brake.
 Start the engine.
 Shift to D, then to N.
 Turn off the engine.
 Leave the ignition switch in ACCESSORY (I) so the steering wheel does not lock.
 Make sure all accessories are turned off to minimize current battery draw.
It is best to tow the vehicle no farther than 80 km
(50 miles), and keep the speed below 55 km/h (35 mph).  Improper towing preparation will damage the
transmission. Follow the above procedure exactly. If
you cannot shift the transmission or start the engine
(automatic transmission), the vehicle must be
transported on a flat-bed.
 Trying to lift or tow the vehicle by the bumpers will cause serious damage. The bumpers are not
designed to support the vehicle’s weight.
08/08/21 14:06:05 61SNR030_010_0013
ProCarManuals.com
DYNOMITE -2009-

µµµµ
µµ
µµ
•••
••• µµ
µµ
µµ
µµ
µµ µ
µµ
Brakes
Air Conditioning
Item Measurement QualificationStandard or New Service Limit
Item Measurement Qualification Standard or New
2-19
Parking brake Distance traveled when lever pulled
with 196 N (20 kgf, 44 lbf) of force 8to10clicks
Brake pedal Pedal height (carpet moved aside) M/T 153 mm (6.02 in.) A/T 158 mm (6.22 in.)
Free play 1 5 mm (0.04 0.20 in.)
Brake disc Thickness Front (except TYPE S)22.9 23.1 mm (0.90 0.91 in.) 21.0 mm (0.83 in.)
Front (TYPE S) 24.9 25.1 mm (0.98 0.99 in.) 23.0 mm (0.91 in.)
Rear 8.9 9.1 mm (0.35 0.36 in.) 8.0 mm (0.31 in.)
Runout Front and rear 0.04 mm (0.0016 in.)
Parallelism Front and rear 0.015 mm (0.0006 in.)
Brake pad Thickness Front (except TYPE S)9.6 10.2 mm (0.38 0.40 in.) 1.6 mm (0.06 in.)
Front (TYPE S) 9.0 9.7 mm (0.35 0.38 in.) 1.6 mm (0.06 in.)
Rear 8.3 9.4 mm (0.33 0.37 in.) 1.6 mm (0.06 in.)
Refrigerant Type HFC-134a (R-134a) Capacity of system 400 450 g (14.1 15.8 oz)
Refrigerant oil Type SP-10 (P/N 38897-P13-A01) Capacity of components Condenser 50 mL (1 2/3 fl·oz) Evaporator 40 mL (1 1/3 fl·oz)
Each Line and
hose10 mL (1/3 fl·oz)
Compressor 75 85mL(21/2 25/6fl·oz)
Compressor Field coil resistance At 20 °C (68 °F) 3.15 3.45 Pulley-to-armature-plate clearance 0.35 0.65 mm (0.014 0.026 in.)
08/08/21 14:07:17 61SNR030_020_0019
ProCarManuals.com
DYNOMITE -2009-

µ
µµµ
Item Measurement Qualification Specification
2-22
Design Specifications
WHEEL
ALIGNMENT
Camber Front 0 ° 00 ’
Rear
(without ‘‘C’’ marks
on the rear upper
arm)1°30’
Rear
(with ‘‘C’’ marks on
the rear upper arm) 0° 45 ’
Caster Front 7 ° 00 ’
Total toe-in Front 0 mm (0 in.) Rear 2 mm (0.08 in.)
Front wheel turning angle Inward 38 ° 46 ’ Outward
(reference)31 ° 14 ’
BRAKES Type of service brake Front Power-assisted self-adjusting ventilated disc Rear Power-assisted self-adjusting solid disc
Type of parking brake Mechanical actuating, rear wheels
Pad friction surface area Front (except Type S)48.4 cm (7.50 sq in.) x 2
Front (Type S) 33.8 cm (5.24 sq in.) x 2
Rear 20.6 cm (3.19 sq in.) x 2
AIR
CONDITIONING Compressor Type Scroll
Capacity 77.1 mL (4.7 cu in.)/rev.
Maximum speed 10,000 rpm
Lubricant capacity 75 mL (2 1/2 fl·oz)
Lubricant type SP-10
Condenser Type Corrugated fin
Evaporator Type Corrugated fin
Blower Type Stabilized swirling flow Motor type 220 W/12 V
Speed control Infinitely variable
Maximum capacity 485 m (17.100 cu ft)/h
Temperature control Air-mix type
Compressor clutch Type Dry, single plate, poly V-belt drive Electrical power
consumption at
20 °C (68 °F)42 W maximum at 12 V
Refrigerant Type HFC-134a (R-134a) Capacity 400 450 g (14.1 15.9 oz)
2
2
2
3
08/08/21 14:07:26 61SNR030_020_0022
ProCarManuals.com
DYNOMITE -2009-

µµ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
Item Measurement Qualification Specification
2-23
ELECTRICAL
RATINGS
Battery 12 V 47 Ah/20 HR (12 V 38 Ah/5 HR)
Fuses Under-hood
fuse/relay box
(’06-07 models)100 A, 80 A, 70 A, 50 A, 40 A, 30 A, 20 A, 15 A, 10 A, 7.5 A
Under-hood
fuse/relay box
(’08-09 models) 100 A, 70 A, 60 A, 50 A, 40 A, 30 A, 20 A, 15 A, 10 A, 7.5 A
Under-dash
fuse/relay box 30 A, 20 A, 15 A, 10 A, 7.5 A
Light bulbs Headlight high beam12 V 60 W (HB3)
Headlight low
beam 12 V 51 W (HB4)
Headlight low
beam (HID) 12 V 35 W (D2R)
Front turn signal
lights 12 V 24/2.2 CP (Amber)
Front side marker
lights 12 V 2 CP
Side turn signal
lights LED
Front parking lights 12 V 3 CP
Front fog lights
(TYPE S, PREMIUM
(’08 model), TECH
PKG) 12 V 55 W (H11)
Rear turn signal
lights 12 V 21 W (Amber)
Rear side marker
lights 12 V 3 CP
Brake/taillights 12 V 21/5 W
Taillights 12 V 5 W
High mount brake
light (except TYPE
S) 12 V 21 W
High mount brake
light (TYPE S) LED
Back-up lights 12 V 16 W
Licenseplatelights 12V 5W
Ceiling light 12 V 8 W
Trunk light 12 V 5 W
Front individual
map lights 12 V 8 W
Gauge lights LED
Indicator lights LED
Ambient light LED
Door courtesy
lights 12 V 3.4 W
Vanity mirror lights 12 V 2 W
Glove box light 12 V 3.4 W
Footwell lights
(TYPE S) LED
Washer reservoir Capacity 4.5 L (4.8 US qt)
08/08/21 14:07:26 61SNR030_020_0023
ProCarManuals.com
DYNOMITE -2009-

(#')Symbol Maintenance Main Items
3-7
Maintenance Main Items
If the message ‘‘SERVICE’’ does not appear more than 12 months after the display is reset, change the engine oil every
year.
NOTE:


 Replace the brake fluid every 3 years independent of the maintenance messages in the information display.
Inspect idle speed every 160,000 miles (256,000 km).
Adjust the valves during services A, B, 1, 2 or 3, only if they are noisy.

















A Replace engine oil (see page 8-10).
Engine oil capacity without oil filter:
K20Z2: 4.0 L (4.2 US qt)
K20Z3: 4.2 L (4.4 US qt)
B Replace engine oil and oil filter (see page 8-11). Engine oil capacity with oil filter:
K20Z2: 4.2 L (4.4 US qt)
K20Z3: 4.4 L (4.6 US qt)
Check front and rear brakes (see page 19-3). Check pad and disc for wear (thickness), damage, and cracks.
Check calipers for damage, leaks, and tightness of mounting bolts.
Check parking brake adjustment (see page 19-7). Check the number of clicks (8 to 10) when the parking brake lever is pulled with 196 N (20 kgf,
44 lbf) of force.
Inspect tie-rod ends, steering gearbox, and gearbox boots (see page 17-5). Check steering linkage.
Check boots for damage and leaking grease.
Check fluid lines for damage and leaks.
Inspect suspension components (see page 18-3). Check bolts for tightness.
Check condition of ball joint boots for deterioration and damage.
Inspect driveshaft boots (see page 16-4). Check boots for cracks and boot bands for tightness.
Inspect brake hoses and lines including VSA lines (see page 19-37). Check the master cylinder and VSA modulator-control unit for damage or leakage.
Inspect all fluid levels and condition of fluids. Engine coolant (see page 10-7)
Automatic transmission fluid (ATF-Z1) (see page 14-231)
Manual transmission fluid (MTF)
5M/T (see page 13-5), 6M/T (see page 13-82)
Clutch fluid (see page 12-7)
Brake fluid (see page 19-9)
Windshield washer fluid (see page 22-234)
Inspect exhaust system: K20Z2 (see page 9-13), K20Z3 (see page 9-14)
Check catalytic converter heat shields, exhaust pipes, and muffler for damage, leaks, and tightness.
Inspect fuel lines (see page 11-326) and connections (see page 11-328). Check for loose connections, cra cks, and deterioration; retighten loose connections and replace
damaged parts.
NOTE: According to state and federal regulations, failure to do the maintenance items marked with an asterisk ( ) will
not void the client’s emissions warranties. However, Acura recommends that all maintenance services be done at the
recommended interval, to ensure long-term reliability.
08/08/21 14:08:32 61SNR030_030_0007
ProCarManuals.com
DYNOMITE -2009-

Ì
Ï
µ
µ
Î
(#')
µ
µ µ
µ
µ
µ
Special Tools Required
YES
NO YES
NO
YES
NO
4-6Starting System
Starter System Circuit Troubleshooting
OTC3131
Alternator, Regulator, Battery & Starter tester OTC3131
Available through the Honda Canada Inc. Technical
Tools Department; FAX
866-398-8665/e-mail:
ch_technicaltools ch.honda.com
NOTE:  Air temperature must be within 15 38 °C (59 100 °F) during this procedure.
 After this inspection, you must reset the engine control module (ECM)/powertrain control module
(PCM). Otherwise, the ECM/PCM will continue to stop
the fuel injectors from operating.
 The battery must be in good condition and fully charged.
1. Connect the alternator, regulator, battery & starter tester (OTC3131) to the battery as shown.
NOTE: The probe is not used for battery testing.
2. Do the BATTERY TEST. ThebatteryisOK.Gotostep3.
If the display indicates BAD BATTERY, replace
the battery, then retest. If the display indicates
CHARGE & RETEST, charge the battery, then retest. 3. Connect the Honda Diagnostic System (HDS) to the
data link connector (DLC) (see step 2 on page 11-3).
4. Turn the ignition switch to ON (II).
5. Make sure the HDS communicates with the vehicle and the ECM/PCM. If it does not communicate,
troubleshoot the DLC circuit (see page 11-204).
6. Select ALL INJECTORS STOP in the PGM-FI INSPECTION menu with the HDS.
7. Set the parking brake, then with the shift lever in N or P (A/T model) or the clutch pedal pressed (M/T
model), turn the ignition switch to START (III).
The starting system is OK. Go to step 14.
Go to step 8.
8. Turn the ignition switch to LOCK (0).
9. Check the electrical connections at the battery, the negative battery cable to the body, the engine
ground cables, and the starter for looseness and
corrosion. Then try cranking the engine again.
Repairing the loose connection corrected the
problem. The starting system is OK. Go to step 14.
Based on the following symptoms, take the
appropriate action:
 If the starter does not crank the engine at all, go to step 10.
 If the starter cranks the engine erratically or too slowly,gotostep12.
 If the starter does not disengage from the flywheel ring gear (M/T model) or torque
converter ring gear (A/T model) when you
release the key, replace the starter, or remove
and disassemble it, and check for the following:
– Starter solenoid and switch malfunction
– Dirty drive gear or damaged overrunning clutch
Does the display indicate GOOD or GOOD, LOWCHARGE? Does t he st ar t er cr ank t he engi ne nor mal l y ?
Does t he st ar t er cr ank t he engi ne nor mal l y ?
08/08/21 14:09:22 61SNR030_040_0007
ProCarManuals.com
DYNOMITE -2009-



(#'
")
µ
µ
YES
NO
11-30911-309
Idle Speed Inspection
BRAKE PEDAL POSITION SWITCH
4P CONNECTOR
BKSW
(LT GRN)JUMPER WIRE
ECM/PCM CONNECTOR A (44P) BKSW (LT GRN) A
9. Connect brake pedal position switch 4P connector
terminal No. 2 to body ground with a jumper wire.
10. Check for continuity between ECM/PCM connector terminal A40 and body ground.
Repair open in the wire between the brake
pedal position switch and the No. 12 HORN/STOP
(15 A) fuse. Also, inspect the brake pedal position
switch (see page 19-6).
Repair open in the wire between the ECM/
PCM (A40) and the brake pedal position switch. NOTE:
 Before checking the idle speed, check these items: – The malfunction indicator lamp (MIL) has not been reported on, and there are no DTCs.
– Ignition timing
– Spark plugs
– Air cleaner
– PCV system
 Apply the parking brake, and make sure the headlights are off.
1. Disconnect the evaporative emission (EVAP) canister purge valve connector (see step 5 on page
11-409).
2. Connect the HDS to the data link connector (DLC) (A) located under the driver’s side of the dashboard.
3. Make sure the HDS communicates with the ECM/ PCM. If it doesn’t, go to the DLC circuit
troubleshooting (see page 11-204).
(cont’d)
Wire side of female terminals
Terminal side of female terminals
Is there continuity?
08/08/21 14:29:38 61SNR030_110_0309
ProCarManuals.com
DYNOMITE -2009-