Page 753 of 2893

Î
µµ
Standard (New): 0.03 mm (0.001 in.) max.
Service Limit: 0.15 mm (0.006 in.) Clutch Disk Inspection and Removal
Standard (New): 8.3 8.9 mm (0.33 0.35 in.)
Service Limit: 6.0 mm (0.24 in.)
12-20Clutch
Clutch Replacement (cont’d)
A
B C
A C
07936-3710100
B
07ZAF-PR8A100A
6. Inspect the pressure plate surface (A) for wear,
cracks, and burning.
7. Inspect for warpage using a straight edge (A) and a feeler gauge (B). Measure across the pressure plate
surface (C). If the most measurement difference is
more than the service limit, replace the pressure
plate. 8. Remove the clutch disc (A), the clutch alignment
shaft (B), and the remover handle (C).
9. Inspect the lining of the clutch disc for signs of slipping or oil. If the clutch disc looks burnt or is
soaked with oil, replace it and the pressure plate as
a set. If the clutch disc is oil soaked, find and repair
the source of the oil leak.
10. Measure the clutch disc thickness. If the measurement is less than the service limit, replace
the clutch disc.
08/08/21 14:42:51 61SNR030_120_0022
ProCarManuals.com
DYNOMITE -2009-
Page 754 of 2893

Î
µµ
Standard (New): 1.65 2.25 mm (0.065 0.089 in.)
Service Limit: 0.7 mm (0.03 in.) Flywheel Inspection
Standard (New): 0.05 mm (0.002 in.) max.
Service Limit: 0.15 mm (0.006 in.)
Flywheel Replacement
12-21
A B B
A
A
07LAB-PV00100
11. Measure the depth of the rivets from the clutch disc lining surface (A) to the rivets (B) on both sides. If
the measurement is less than the service limit,
replace the clutch disc.
12. Remove the ring gear holder. 13. Inspect the ring gear teeth for wear and damage.
14. Inspect the clutch disc mating surface on the
flywheel for wear, cracks, and burning.
15. Measure the flywheel (A) runout using a dial indicator (B). Through at least two full turns with
pushing against the flywheel each time you turn it
to take up the crankshaft thrust washer clearance. If
the measurement is not within the standard,
replace the flywheel, and recheck the runout; go to
step 16.
16. Install the ring gear holder (A).
17. Loosen the flywheel mounting bolts in a cri sscross
pattern in several steps. Remove the bolts, then
remove the flywheel and the ring gear holder.
(cont’d)
08/08/21 14:42:52 61SNR030_120_0023
ProCarManuals.com
DYNOMITE -2009-
Page 755 of 2893

Î
Î
µµ
Crankshaft Pilot Bushing Inspection Crankshaft Pilot Bushing Replacement
12-22Clutch
Clutch Replacement (cont’d)
A
07LAB-PV00100
B
K20Z2enginemodel:
12x1.0mm
103 N·m
(10.5kgf·m,76lbf·ft)
K20Z3enginemodel:
122 N·m
(12.5kgf·m,90lbf·ft) B
07936-KC10500C
07741-0010201
A
C
07746-0010800
B
07749-0010000
2.4 2.6 mm (0.09 0.10 in.)
A
18. Install the flywheel on the crankshaft, and install
the mounting bolts finger-tight.
19. Install the ring gear holder (A), then torque the flywheel mounting bolts (B) in a cri sscross pattern
in several steps.
20. Inspect the crankshaft pilot bushing for wear and damage.
21. Inspect the inside surface of the crankshaft pilot bushing with your finger. If the crankshaft pilot
bushing is not smooth, replace it; then go to step
22. 22. Remove the crankshaft pilot bushing (A) using the
bearing remover shaft (B) and the slide hammer (C).
23. Install a new crankshaft pilot bushing (A) into the crankshaft using the 15 x 135L driver handle (B)
and the 22 x 24 mm bearing driver attachment (C).
08/08/21 14:42:53 61SNR030_120_0024
ProCarManuals.com
DYNOMITE -2009-
Page 756 of 2893

Î
Clutch Disc and Pressure Plate Installation
Specified Torque: 25 N·m (2.6 kgf·m, 19 lbf·ft)
12-23
D
07ZAF-PR8A100
E
07936-3710100
(P/N 08798-9002) C
B (P/N 08798-9002)A
B A D
07936-3710100
C
07ZAF-PR8A100 B
07LAB-PV00100
A
24. Temporarily install the clutch disc onto the splines of the transmission mainshaft. Make sure the clutch
disc slides freely on the mainshaft.
25. Apply a light coat of super high temp urea grease (P/N 08798-9002) to the crankshaft pilot bushing (A).
26. Apply super high temp urea grease (P/N 08798-9002) to the splines (B) of the clutch disc (C),
then install the clutch disc using the clutch
alignment shaft (D) and the remover handle (E).
27. Install the pressure plate (A) and the mounting bolts (B) finger-tight. 28. Torque the mounting bolts (A) in a cri
sscross
pattern. Tighten the bolts in several steps to
prevent warping the diaphragm spring.
29. Remove the ring gear holder (B), the clutch alignment shaft (C), and the remover handle (D).
30. Make sure the diaphragm spring fingers are all the same height.
31. Do the release bearing inspection, and replace it if necessary.
32. Install the transmission; 5-speed model (see page 13-14), 6-speed model (see page 13-91).
(cont’d)
08/08/21 14:42:54 61SNR030_120_0025
ProCarManuals.com
DYNOMITE -2009-
Page 757 of 2893

Î
Î
µ
µ
µµ
µµ
Transmission Side
Release Bearing Removal
Release Bearing Inspection Release Bearing Installation
12-24Clutch
Clutch Replacement (cont’d)
A
B
C D
E
AD
E B
C (P/N 08798-9002)
1.0 1.6 g
(0.04 0.06 oz)
(P/N 08798-9002)
0.4 1.0 g (0.01 0.04 oz)
(P/N 08798-9002)
0.4 1.0 g (0.01 0.04 oz)
1. Remove the transmission; 5-speed model (see page 13-7), 6-speed model (see page 13-84).
2. Remove the release fork boot (A) from the clutch housing (B).
3. Remove the release fork (C) from the clutch housing by squeezing the release fork set spring (D)
with pliers. Remove the release bearing (E).
4. Check the play of the release bearing by spinning it by hand. If there is excessive play or noise, replace
the release bearing.
NOTE: The release bearing is packed with grease.
Do not wash it in solvent. 5. Apply super high temp urea grease (P/N
08798-9002) to the release fork (A), the release fork
bolt (B), the release bearing (C), and the release
bearing guide (D), in the shaded areas, then set the
release fork set spring (E).
08/08/21 14:42:54 61SNR030_120_0026
ProCarManuals.com
DYNOMITE -2009-
Page 758 of 2893
Î
12-25
A
D E
B
CF
B BA
6. With the release fork (A) slid between the release
bearing pawls (B), install the release bearing on the
mainshaft while inserting the release fork through
the hole (C) in the clutch housing.
7. Align the detent (D) of the release fork with the release fork bolt (E), then press the detent of the
release fork over the release fork bolt squarely.
8. Install the release fork boot (F). Make sure the boot seals around the release fork and the clutch
housing. 9. Move the release fork (A) right and left to make
sure that it fits properly against the release bearing
(B) and that the release bearing slides smoothly.
Wipe off any excess grease.
10. Install the transmission; 5-speed model (see page 13-14), 6-speed model (see page 13-91).
08/08/21 14:42:55 61SNR030_120_0027
ProCarManuals.com
DYNOMITE -2009-
Page 759 of 2893
(#'
/)
08/08/21 14:42:55 61SNR030_120_0028
ProCarManuals.com
DYNOMITE -2009-
Page 760 of 2893

Î
(#'
)
12-10 Clutch
Clutch Pedal Assembly Replacement
B
D
E A
C
G
F H
I
(Multipurpose Grease)(Multipurpose Grease)
A
B C
13 N·m
(1.3 kgf·m,
9.4 lbf·ft)
D
(Multipurpose Grease) C
13 N·m
(1.3 kgf·m,
9.4 lbf·ft)
B
22 N·m
(2.2 kgf·m,
16 lbf·ft)
A
E
F
F
1. Disconnect the clutch pedal position switch
connector (A) and the clutch interlock switch
connector (B).
2. Pry out the lock pin (C), and pull the clevis pin (D) out of the clevis.
3. Remove the master cylinder mounting nuts (E) and the clutch pedal mounting bolt (F).
4. Remove the clutch pedal assembly (G).
5. Remove the clutch interlock switch (H), and the clutch pedal position switch (I).
6. Loosely install the clutch interlock switch (A), and the clutch pedal position switch (B). 7. Install the clutch pedal assembly (A).
8. Install the clutch pedal mounting bolt (B) and the
master cylinder mounting nuts (C).
9. Apply grease to the clevis pin (D) and the mating surfaces of the clevis and the pedal. Slide the clevis
pin into the clevis, then install a lock pin (E).
10. Adjust the clutch pedal, the clutch pedal position switch, and the clutch interlock switch (see page
12-8).
NOTE: Connect the switch connectors (F) after
adjusting them.
11. Check the clutch operation.
08/08/21 14:42:31 61SNR030_120_0012
ProCarManuals.com
DYNOMITE -2009-