Page 1761 of 2893

20-85
A
B
B
A
B D
B
5x0.8mm
5N·m
(0.5 kgf·m,
4lbf·ft)
Fastener Locations
:Bolt,2
C
E
F
G A
B
C
A
Fastener Locations :Bolt,4
8x1.25mm
22 N·m
(2.2 kgf·m,
16 lbf·ft) A
6. Push the hook (A) with a flat-tip screwdriver
wrapped with protective tape, and turn the holder
(B) 90 °, then pull it out.
7. Remove the individual map light assembly (A). –1 Remove the lenses (B).
–2 Remove the bolts.
–3 If equipped, release the four tabs (C), then pullout the moonroof switch (D) or the navigation
microphone.
–4 Disconnect the front individual map light connector (E). If equipped, disconnect the
moonroof switch connector (F) and the
navigation microphone connector (G). 8. Without moonroof: Remove the driver’s dashboard
undercover (see page 20-104).
9. Detach the harness clips (A) from the A-pillar (B), and disconnect the roof wire harness connector (C).
10. Remove the center console (see page 20-92).
11. Slide both front seats all the way back, and recline the seat-backs fully.
12. Remove the bolts securing the parking brake base frame (A), and lay it down as needed.
(cont’d)
08/08/21 15:01:40 61SNR030_200_0087
ProCarManuals.com
DYNOMITE -2009-
Page 1762 of 2893

Cushion tape A: P/N 91903-SNA-003
100x50mm(3.94x1.97in.)
Cushion tape B: P/N 91902-SNA-003 50x50mm(1.97x1.97in.)
20-86Interior Trim
Headliner Removal/Installation (cont’d)
B
Fastener Locations
:Clip,2(White)
A B
C
B
C
F
Without moonroof
BD
C
D
C
D
A
ED
With moonroof
C
D
Fastener Locations
: Cushion tape, 8
BB
BB
B B
B
A
A, B
13. Lower the headliner (A).
–1 Remove the front door opening seals (B) andrear door opening seals (C) from each roof
portion.
–2 With the help of an assistant, detach the rear clips by pulling the rear portion of the
headliner down.
–3 With moonroof: Release the Velcro fastener (D) by lowering the headliner.
–4 With moonroof: Release the hook (E) of the moonroof by moving the headliner rearward.
14. Lower the front of the headliner below the steering wheel. Rotate the liner, and pull it along with the
roof wire harness (F) (without moonroof) out
through the passenger’s front door. Do not bend
the liner. Bending the liner will crease and damage
it. 15. If necessary, remove the cushion tape (A, B)
fastening the roof wire harness (C) to the headliner
(D), then remove them from the headliner.
08/08/21 15:01:41 61SNR030_200_0088
ProCarManuals.com
DYNOMITE -2009-
Page 1763 of 2893

Î
20-87
Fastener Locations:Bolt,1
A :Bolt,2
B
A
B C
B D
5x0.8mm
6N·m
(0.6 kgf·m, 4 lbf·ft)
5x0.8mm
6N·m
(0.6 kgf·m, 4 lbf·ft)
16. If necessary, remove the side curtain airbag mounting bolt (A) and grab handle bracket
mounting bolts (B), then remove the grab handle
bracket (C) from each side by releasing the hooks
(D). 17. Install the headliner in the reverse order of removal,
and note these items:
If the side curtain airbag has deployed, replace the headliner and related parts with new ones
(see page 24-185).
To prevent the side curtain airbags from deploying improperly and possibly causing
injury, inspect the removed pieces and replace
them if they have any of the following damage:
– Any crease or tears in the headliner (A)
– Any cracks or breakage in the grab handle (B)
– Any damages around the grab handle holes (C) or sunvisor holes in the headliner
– Any cracks in the sunvisor stay base (D)
– Any bends or cracks in the sunvisor stay shaft (E)
– Any cracks in the sunvisor base (F)
– Any cracks or breakage in the vanity mirror base (G)
– Any Velcro fasteners (H) and the clip bases (I) which have come off the headliner
When installing the grab handle, push on the grab handle against the bracket (J) until the clips
(K) snap into place securely.
If the clips are damaged or stress-whitened, replace them with new ones.
Replace the removed cushion tape with new ones.
Check that both sides of the headliner are securely attached to the trim.
Make sure the headliner overlaps the trim pieces correctly (see page 24-187).
When reinstalling the headliner through the front passenger’s door opening, be careful not to fold
or bend it. Also, be careful not to scratch the
body.
Check for any DTCs that may have been set during repairs, and clear them.
Do the battery terminal reconnection procedure (see page 22-68).
(cont’d)
08/08/21 15:01:41 61SNR030_200_0089
ProCarManuals.com
DYNOMITE -2009-
Page 1764 of 2893

(#'
)
H
eadliner
Grab handle
Sunvisor Special Tools Required
20-8820-88
Interior Trim
Headliner Removal/Installation
(cont’d)
Carpet Replacement
A
C
H
I
C
J K
B
B
F
D
E G
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S
RS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE: Put on gloves to protect your hands.
Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
Take care not to damage, wrinkle, or twist the carpet.
Be careful not to damage the dashboard or other interior trim pieces.
1. Remove these items: Front seats, both sides (see page 20-118)
Rear seat cushion (see page 20-133)
Front door sill trim, both sides (see page 20-66)
Rear door sill trim, both sides (see page 20-67)
Kick panels, both sides (see step 5 on page 20-67)
B-pillar lower trim (see page 20-72)
Driver’s dashboard undercover (see page 20- 103)
Passenger’s dashboard undercover (see page 20-104)
Center console (see page 20-92)
Steering joint cover (see page 17-10)
08/08/21 15:01:42 61SNR030_200_0090
ProCarManuals.com
DYNOMITE -2009-
Page 1765 of 2893

(#'
)
H
eadliner
Grab handle
Sunvisor Special Tools Required
20-8820-88
Interior Trim
Headliner Removal/Installation
(cont’d)
Carpet Replacement
A
C
H
I
C
J K
B
B
F
D
E G
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S
RS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE: Put on gloves to protect your hands.
Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
Take care not to damage, wrinkle, or twist the carpet.
Be careful not to damage the dashboard or other interior trim pieces.
1. Remove these items: Front seats, both sides (see page 20-118)
Rear seat cushion (see page 20-133)
Front door sill trim, both sides (see page 20-66)
Rear door sill trim, both sides (see page 20-67)
Kick panels, both sides (see step 5 on page 20-67)
B-pillar lower trim (see page 20-72)
Driver’s dashboard undercover (see page 20- 103)
Passenger’s dashboard undercover (see page 20-104)
Center console (see page 20-92)
Steering joint cover (see page 17-10)
08/08/21 15:01:42 61SNR030_200_0090
ProCarManuals.com
DYNOMITE -2009-
Page 1766 of 2893
Î
20-89
D
E B
C
A
D
Fastener Locations :Clip,1
B :Clip,1
D
A B C
D A
B
D
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
C
C
2. Release the hooks (A) to remove the accelerator
pedal clip (B). While pushing down the back-up
spring (C), pull back the accelerator pedal (D) to
release the hook (E).
3. Remove the footrest (A). –1 Remove the lower clip (B) with a 6 mmhexagon wrench, from the stud bolt (C).
–2 Remove the upper clip (D) with a flat-tip screwdriver, from the stud bolt. 4. Disconnect the SRS unit connector (A), antenna
connector (B), and detach the wire harness clips (C).
Remove the ground bolt (D) with a TORX T30 bit.
(cont’d)
Use a TORX T30 bit.
08/08/21 15:02:46 61SNR030_200_0091
ProCarManuals.com
DYNOMITE -2009-
Page 1767 of 2893
20-90Interior Trim
Carpet Replacement (cont’d)
Fastener Locations
:Bolt,2
A:Bolt,1
C
D
6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A A
B
B
A A
Fastener Locations :Clip,2
5. Remove the bolts (A, B), and detach the connector clip (C), then remove the center pipe extension (D).
6. Remove the rear heater joint duct (A). 7. Disconnect the parking brake cables from the
equalizer (see page 19-40).
8. Remove the floor mat holders (A) from the driver’s side.
9. Remove the clips.
08/08/21 15:02:46 61SNR030_200_0092
ProCarManuals.com
DYNOMITE -2009-
Page 1768 of 2893
20-91
AB
C
C
10. Release the Velcro fastener (A), then pull the carpet (B) out from under the dashboard. 11. Pull the seat harnesses (C) out through the hole in
the carpet, then remove the carpet.
12. Install the carpet in the reverse order of removal, and note these items:
Take care not to damage, wrinkle or twist the carpet.
Make sure the seat harnesses and parking brake cables are routed correctly.
If the clips are damaged or stress-whitened, replace them with new ones.
Push the Velcro fasteners and the clips into place securely.
Push the accelerator pedal hooks into place securely, and verify that the pedal is properly
fastened to the floor.
08/08/21 15:02:47 61SNR030_200_0093
ProCarManuals.com
DYNOMITE -2009-