2006 ACURA CSX maintenance schedule


(#')
Information Display
Driver’s Side Dashboard:
3-4Maintenance Minder
General Information
MAINTENANCE MINDER INDICATOR
INFORMATION DISPLAY
SEL/RESET BUTTON
The maintenance minder is an important feature of the information display. Based on engine and transmission
operating conditions, the Acura CSX’s onboard computer (ECM/PCM) calculates the remaining engine oil and the
automatic transmission fluid life. The system also displays the remaining engine oil life along with the code(s) for
other scheduled maintenance items needing service.
08/08/21 14:08:30 61SNR030_030_0004
ProCarManuals.com
DYNOMITE -2009-

µµ










Service Information
3-5
A
C D
A
B A
A
1. The remaining engine oil life (A) is shown as apercentage on the information display. To see the
current engine oil life, turn the ignition switch to
ON (II), then push and release the SEL/RESET
button repeatedly until the engine oil life displays.
2. When the ignition switch is ON (II), and the remaining engine oil life is 6 % to 15 %, the
remaining engine oil life (A) and other scheduled
maintenance item(s) needing service are displayed.
The maintenance minder indicator (B) also comes
on when the engine oil life is 15 % or less. To
cancel the display and the indicator, press SEL/
RESET button.
 Complete list of maintenance main items (C) (see page 3-7).
 Complete list of maintenance sub items (D) (see page 3-8). 3. When the ignition switch is ON (II), and the
remaining engine oil life is 1 % to 5 %, the message
‘‘SERVICE’’ (A) is displayed along with engine oil
life and the same maintenance item code(s).
4. When the ignition switch is ON (II), and the remaining engine oil life is 0 %, the engine oil life
indicator (A) blinks. Pressing SEL/RESET button
cancels the display, but the maintenance minder
indicator stays on.
5. If the indicated maintenance is not done, the engine oil life indicator shows a negative mileage, for
example ‘‘ 10,’’ on the display. If the negative
mileage is between 0 and 9, the indicator is
displayed for only a few seconds when the ignition
switch is turned to ON (II). The negative mileage
remains displayed after the vehicle is driven more
than 10 km after 0 % oil life is reached, and the
display cannot be canceled.
This means the indicated maintenance item(s)
should have been done more than 10 km ago.
(cont’d)
08/08/21 14:08:31 61SNR030_030_0005
ProCarManuals.com
DYNOMITE -2009-

Î
System Structure
Control unit
Indicators
18-58TPMS
System Description (cont’d)
Vehicle
Indicators (LED)
Gauge Control Module (Tach)
Communication
via F-CAN
Control Unit
(with radio
frequency antenna)
Tire Pressure Sensor
(sensor-transmitter
with acceleration sensor) Wheel
(TPMS type)
Tire Pressure Sensor
(sensor-transmitter
with acceleration sensor)
Tire Pressure Sensor
(sensor-transmitter
with acceleration sensor)
Tire Pressure Sensor
(sensor-transmitter
with acceleration sensor)
Wheel
(TPMS type)
Wheel
(TPMS type) Wheel
(TPMS type)
Once the vehicle speed exceeds 45 km/h (28 mph), the TPMS control unit monitors all four tire pressure sensors and
the system function. If it detects low pressure in a tire, it alerts the driver by turning on the low tire pressure indicator.
If it detects a problem in the system, it turns on the TPMS indicator.
Mounted inside of the dash, the TPMS control unit receives wireless pressure sensor ID signals
every time the vehicle
speeds exceeds 45 km/h (28 mph). It also receives wireless signals from the transmitters for tire pressure and the
sensor condition, and it continuously monitors and controls the system. The TPMS control unit cannot directly
determine the position (location) of a tire pressure sensor(s) on the vehicle since it is a wireless system. TPMS sensor
locations will change during scheduled vehicle maintenance (tire rotation).
NOTE: To determine the actual location of each TPMS wheel sensor on the vehicle, do the tire pressure sensor
location procedure (see page 18-53). Once the tire pressure sensor locations are identified, write the sensor ID on the
side wall of the tire with a tire crayon to eliminate confusion.
Two indicators are in the gauge control module (tach): The low tire pressure indicator comes on when any tire
pressure is low, and the TPMS indicator that comes on only if there’s a problem with the system.
The low tire pressure indicator alerts the driver that a tire(s) pressure is low, but does not specify the tire(s) location.
08/08/21 14:58:24 61SNR030_180_0058
ProCarManuals.com
DYNOMITE -2009-