2006 ACURA CSX refrigerant type

µµµµ
µµ
µµ
•••
••• µµ
µµ
µµ
µµ
µµ µ
µµ
Brakes
Air Conditioning
Item Measurement QualificationStandard or New Service Limit
Item Measurement Qualification Standard or New
2-19
Parking brake Distance traveled when lever pulled
with 196 N (20 kgf, 44 lbf) of force 8to10clicks
Brake pedal Pedal height (carpet moved aside) M/T 153 mm (6.02 in.) A/T 158 mm (6.22 in.)
Free play 1 5 mm (0.04 0.20 in.)
Brake disc Thickness Front (except TYPE S)22.9 23.1 mm (0.90 0.91 in.) 21.0 mm (0.83 in.)
Front (TYPE S) 24.9 25.1 mm (0.98 0.99 in.) 23.0 mm (0.91 in.)
Rear 8.9 9.1 mm (0.35 0.36 in.) 8.0 mm (0.31 in.)
Runout Front and rear 0.04 mm (0.0016 in.)
Parallelism Front and rear 0.015 mm (0.0006 in.)
Brake pad Thickness Front (except TYPE S)9.6 10.2 mm (0.38 0.40 in.) 1.6 mm (0.06 in.)
Front (TYPE S) 9.0 9.7 mm (0.35 0.38 in.) 1.6 mm (0.06 in.)
Rear 8.3 9.4 mm (0.33 0.37 in.) 1.6 mm (0.06 in.)
Refrigerant Type HFC-134a (R-134a) Capacity of system 400 450 g (14.1 15.8 oz)
Refrigerant oil Type SP-10 (P/N 38897-P13-A01) Capacity of components Condenser 50 mL (1 2/3 fl·oz) Evaporator 40 mL (1 1/3 fl·oz)
Each Line and
hose10 mL (1/3 fl·oz)
Compressor 75 85mL(21/2 25/6fl·oz)
Compressor Field coil resistance At 20 °C (68 °F) 3.15 3.45 Pulley-to-armature-plate clearance 0.35 0.65 mm (0.014 0.026 in.)
08/08/21 14:07:17 61SNR030_020_0019
ProCarManuals.com
DYNOMITE -2009-

µ
µµµ
Item Measurement Qualification Specification
2-22
Design Specifications
WHEEL
ALIGNMENT
Camber Front 0 ° 00 ’
Rear
(without ‘‘C’’ marks
on the rear upper
arm)1°30’
Rear
(with ‘‘C’’ marks on
the rear upper arm) 0° 45 ’
Caster Front 7 ° 00 ’
Total toe-in Front 0 mm (0 in.) Rear 2 mm (0.08 in.)
Front wheel turning angle Inward 38 ° 46 ’ Outward
(reference)31 ° 14 ’
BRAKES Type of service brake Front Power-assisted self-adjusting ventilated disc Rear Power-assisted self-adjusting solid disc
Type of parking brake Mechanical actuating, rear wheels
Pad friction surface area Front (except Type S)48.4 cm (7.50 sq in.) x 2
Front (Type S) 33.8 cm (5.24 sq in.) x 2
Rear 20.6 cm (3.19 sq in.) x 2
AIR
CONDITIONING Compressor Type Scroll
Capacity 77.1 mL (4.7 cu in.)/rev.
Maximum speed 10,000 rpm
Lubricant capacity 75 mL (2 1/2 fl·oz)
Lubricant type SP-10
Condenser Type Corrugated fin
Evaporator Type Corrugated fin
Blower Type Stabilized swirling flow Motor type 220 W/12 V
Speed control Infinitely variable
Maximum capacity 485 m (17.100 cu ft)/h
Temperature control Air-mix type
Compressor clutch Type Dry, single plate, poly V-belt drive Electrical power
consumption at
20 °C (68 °F)42 W maximum at 12 V
Refrigerant Type HFC-134a (R-134a) Capacity 400 450 g (14.1 15.9 oz)
2
2
2
3
08/08/21 14:07:26 61SNR030_020_0022
ProCarManuals.com
DYNOMITE -2009-


(#')
Application Lubricant or Fluid
3-2Lubricants and Fluids
API CERTIFICATION SEAL
For details of the lubrication points and the type of lubricants to be applied, refer to the illustrated index and the various work procedures (such
as Assembly/Reassembly, Replacement, Overhaul, Installation, etc.) contained in each section.


A Engine Acura Motor Oil:
K20Z2: P/N CA66808 (5W-20)
K20Z3: P/N CA66807 (5W-30)
Look for the API certification seal on the oil container. Make sure it says ‘‘For
Gasoline Engines.’’ SAE viscosity: See chart.
B Manual transmission Acura Manual Transmission Fluid (MTF): P/N 08798-9033C Always use Acura MTF. Using motor oil can cause stiffer shifting because it
does not contain the proper additives.
Automatic transmission Acura Automatic Transmission Fluid (ATF-Z1): P/N CA66704 Always use Acura ATF-Z1. Using a non-Acura ATF can affect shift quality.
C
D Brake system (including VSA lines)
Clutch system (manual transmission) Honda DOT 3 Brake Fluid: P/N 08798-9008
Always use Honda DOT 3 Brake Fluid. Using a non-Honda brake fluid can
cause corrosion and decrease the life of the system.
E F
G H I
J
K Brake booster clevis pin
Clutch master cylinder clevis pin (manual
transmission)
Release fork (manual transmission)
Battery terminals
Fuel fill door
Trunk hinges
Hood hinges and hood latch Multipurpose Grease
L
M Shift cable ends (manual transmission)
Caliper piston seal and boot, caliper pins and boots Honda Silicone Grease: P/N 08C30-B0234M
N Air conditioning compressor Compressor Oil: SP-10 (P/N 38897-P13-A01AH) for refrigerant HFC-134a (R-134a)
O Cooling system Honda Long Life Antifreeze/Coolant Type 2: P/N CA66688
08/08/21 14:08:29 61SNR030_030_0002
ProCarManuals.com
DYNOMITE -2009-


21-84Climate Control
A/C Compressor Replacement (cont’d)
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
A
7. Remove the mounting bolts and the A/C
compressor (A). Be careful not to damage the
radiator fins when removing the A/C compressor. 8. Install the compressor in the reverse order of
removal, and note these items:
 Inspect the A/C lines for any signs of contamination.
 If you’re installing a new A/C compressor, you must calculate the amount of refrigerant oil to be
removed from it (see page 21-7). A new A/C
compressor comes with a full charge of oil.
 Replace the O-rings with new ones at each fitting, and apply a thin coat of refrigerant oil before
installing them. Be sure to use the correct O-rings
for HFC-134a (R-134a) to avoid leakage.
 Use refrigerant oil (SP-10) for HFC-134a SANDEN spiral type A/C compressor only.
 To avoid contamination, do not return the oil to the container once dispensed, and never mix it
with other refrigerant oils.
 Immediately after using the oil, reinstall the cap on the container, and seal it to avoid moisture
absorption.
 Do not spill the refrigerant oil on the vehicle; it may damage the paint; if the refrigerant oil
contacts the paint, wash it off immediately.
 Charge the system (see page 21-92).
08/08/21 14:43:45 61SNR030_210_0085
ProCarManuals.com
DYNOMITE -2009-