Page 1841 of 2893

(#'
)
Special Tool Required
20-156
Trunk Lid
Trunk Lid Torsion Bar Replacement
B
A
A
B
B
A
07AAF-SNAA100 A
A B
=Normal position
=Higher tension
Torsion bar assembly tool 07AAF-SNAA100
1. Remove the torsion bars (A) from the torsion bar center clip (B).
2. Put on gloves to protect your hands. Remove the torsion bars with the torsion bar assembly tool
from both trunk lid hinges. First remove the left
torsion bar (A), then remove the right torsion bar
(B). 3. Remove the torsion bar center clip (A) from the
body.
4. Install the torsion bar in the reverse order of removal, and note these items:
The shapes of the left torsion bar (A) and the right torsion bar (B) are shown. Install the torsion
bars properly.
Adjust the torsion bars forward or rearward with the torsion bar assembly tool.
The torsion bars were installed at the factory in the normal position, as shown.
Make sure the trunk lid opens properly and locks securely.
08/08/21 15:04:58 61SNR030_200_0158
ProCarManuals.com
DYNOMITE -2009-
Page 1842 of 2893
(#'
)
(#'
)
20-15720-157
Trunk Lid Weatherstrip
Replacement Trunk Lid Cushion Replacement
A
B
C
D A
Front A
B C
C
A
1. Remove the trunk lid weatherstrip (A) by pulling it off.
2. Apply clear weatherstrip sealant (B) into the channel of the trunk lid weatherstrip all the way
around.
3. Locate the painted alignment mark (C or D) on the trunk lid weatherstrip. Align the painted mark in the
center of the trunk lid opening, and install the trunk
lid weatherstrip all the way around in the direction
shown. Make sure there are no wrinkles in the
weatherstrip.
4. Check for water leaks (see step 9 on page 20-29). NOTE: Put on gloves to protect your hands.
1. Remove the trunk lid trim (see page 20-82).
2. Detach the clips (A) by pushing it from the hole in the trunk lid (B), then remove the trunk lid cushion
(C). Take care not to scratch the trunk lid.
3. Install the cushion in the reverse order of removal.
08/08/21 15:04:58 61SNR030_200_0159
ProCarManuals.com
DYNOMITE -2009-
Page 1843 of 2893
(#'
")
20-158 Fuel Fill Door
Fuel Fill Door Adjustment
B
A
6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
1. Slightly loosen the hinge mounting bolts (A).
2. Adjust the fuel fill door (B) in or out until it’s flush with the body, and up or down as necessary to
equalize the gaps.
3. Tighten the hinge mounting bolts.
4. Check that the fuel fill door opens properly and locks securely, and check that the rear of the door is
flush with the body. 5. Apply multipurpose grease to each location
indicated by the arrows.
6. Apply touch-up paint to the hinge mounting bolts and around the hinges.
08/08/21 15:04:59 61SNR030_200_0160
ProCarManuals.com
DYNOMITE -2009-
Page 1844 of 2893
(#'
)
20-159
Fuel Cap Adapter Replacement
Fastener Location :Screw,1
A Fastener Locations
:Bolt,2
AB
6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
NOTE: Take care not to scratch the body.1. Remove the screw. Remove the fuel cap (A) by turning it counterclockwise. 2. Remove the bolts, and lower the fuel filler pipe (A),
then remove it from the fuel cap adapter (B).
3. Turn the fuel cap adapter (A), then remove it.
4. Install the adapter in the reverse order of removal.
08/08/21 15:04:59 61SNR030_200_0161
ProCarManuals.com
DYNOMITE -2009-
Page 1845 of 2893
(#'
)
’06-08 Models
20-160 Exterior Trim
Front Grille Replacement
Fastener Locations
:Clip,6
A B
A
B Fastener Locations
:Screw,6
A B
A
NOTE: Take care not to scratch the bumper and the
grille. 1. Remove the front bumper (see page 20-146).
2. Remove the clips, then pull the front bumper grille (A) forward from the front bumper (B).
3. If necessary, remove the front ‘‘A’’ emblem from the front grille (see page 20-170). 4. If necessary, remove the screws, then remove the
front grille moldings (A) from the front grille base
(B).
5. Install the grille in the reverse order of removal.
08/08/21 15:05:00 61SNR030_200_0162
ProCarManuals.com
DYNOMITE -2009-
Page 1846 of 2893
Î
Î
(#'
)
’09 Model
20-161
Fastener Locations :Screw,2 :Clip,4
B
A Fastener Locations
:Screw,19
BC
A
NOTE: Take care not to scratch the bumper and the
grille. 1. Remove the front bumper (see page 20-146).
2. Remove the screws, and remove the front grille (A) from the front bumper (B). 3. Remove the screws, then separate the front grille
lower molding (A), the front grille upper molding
(B), and the front grille base (C).
4. Replace the emblem, if necessary (see page 20-170).
5. Install the grille in the reverse order of removal.
08/08/21 15:05:00 61SNR030_200_0163
ProCarManuals.com
DYNOMITE -2009-
Page 1847 of 2893
(#'
)
’06-08 Models
20-160 Exterior Trim
Front Grille Replacement
Fastener Locations
:Clip,6
A B
A
B Fastener Locations
:Screw,6
A B
A
NOTE: Take care not to scratch the bumper and the
grille. 1. Remove the front bumper (see page 20-146).
2. Remove the clips, then pull the front bumper grille (A) forward from the front bumper (B).
3. If necessary, remove the front ‘‘A’’ emblem from the front grille (see page 20-170). 4. If necessary, remove the screws, then remove the
front grille moldings (A) from the front grille base
(B).
5. Install the grille in the reverse order of removal.
08/08/21 15:05:00 61SNR030_200_0162
ProCarManuals.com
DYNOMITE -2009-
Page 1848 of 2893
Î
Î
(#'
)
’09 Model
20-161
Fastener Locations :Screw,2 :Clip,4
B
A Fastener Locations
:Screw,19
BC
A
NOTE: Take care not to scratch the bumper and the
grille. 1. Remove the front bumper (see page 20-146).
2. Remove the screws, and remove the front grille (A) from the front bumper (B). 3. Remove the screws, then separate the front grille
lower molding (A), the front grille upper molding
(B), and the front grille base (C).
4. Replace the emblem, if necessary (see page 20-170).
5. Install the grille in the reverse order of removal.
08/08/21 15:05:00 61SNR030_200_0163
ProCarManuals.com
DYNOMITE -2009-