2006 ACURA CSX trunk release


(#')
Application Lubricant or Fluid
3-2Lubricants and Fluids
API CERTIFICATION SEAL
For details of the lubrication points and the type of lubricants to be applied, refer to the illustrated index and the various work procedures (such
as Assembly/Reassembly, Replacement, Overhaul, Installation, etc.) contained in each section.


A Engine Acura Motor Oil:
K20Z2: P/N CA66808 (5W-20)
K20Z3: P/N CA66807 (5W-30)
Look for the API certification seal on the oil container. Make sure it says ‘‘For
Gasoline Engines.’’ SAE viscosity: See chart.
B Manual transmission Acura Manual Transmission Fluid (MTF): P/N 08798-9033C Always use Acura MTF. Using motor oil can cause stiffer shifting because it
does not contain the proper additives.
Automatic transmission Acura Automatic Transmission Fluid (ATF-Z1): P/N CA66704 Always use Acura ATF-Z1. Using a non-Acura ATF can affect shift quality.
C
D Brake system (including VSA lines)
Clutch system (manual transmission) Honda DOT 3 Brake Fluid: P/N 08798-9008
Always use Honda DOT 3 Brake Fluid. Using a non-Honda brake fluid can
cause corrosion and decrease the life of the system.
E F
G H I
J
K Brake booster clevis pin
Clutch master cylinder clevis pin (manual
transmission)
Release fork (manual transmission)
Battery terminals
Fuel fill door
Trunk hinges
Hood hinges and hood latch Multipurpose Grease
L
M Shift cable ends (manual transmission)
Caliper piston seal and boot, caliper pins and boots Honda Silicone Grease: P/N 08C30-B0234M
N Air conditioning compressor Compressor Oil: SP-10 (P/N 38897-P13-A01AH) for refrigerant HFC-134a (R-134a)
O Cooling system Honda Long Life Antifreeze/Coolant Type 2: P/N CA66688
08/08/21 14:08:29 61SNR030_030_0002
ProCarManuals.com
DYNOMITE -2009-

Seats
Bumpers
Hood
Trunk Lid
Fuel Fill Door
Exterior TrimFenderwell
Openers
Frame......................
............................................... ...............
................ .......
........................................... .........................
..............................
........................................... ......................
........................................... ...
...
......................
............................................... ...............
................ .......
........................................... .........................
..............................
........................................... ......................
........................................... ...
...
Component Location Index
. 20-116
Front Seat Active Head Restraint Inspection . 20-117
Front Seat Removal/Installation . 20-118
Front Seat Frame Replacement . 20-120
Front Seat-back Cover Replacement . 20-123
Front Seat Cushion Cover Replacement . 20-127
Rear Seat Removal/Installation . 20-131
Rear Seat-back Latch Replacement . 20-135
Rear Seat-back Release Lever/Cable Removal/Installation . 20-136
Rear Seat Armrest Beverage Holder Replacement . 20-137
Rear Seat Armrest Replacement . 20-138
Rear Seat-back Cover Replacement . 20-139
Rear Seat Side Bolster Cover Replacement . 20-143
Rear Seat Cushion Cover Replacement . 20-143
Rear Seat Armrest Cover Replacement . 20-144
.........
...........................................
........................................... ..........
........................................... .........
...........................................
........................................... ..........
...........................................
Front Bumper Removal/Installation . 20-146
Front Bumper Lower Grille
Replacement . 20-148
Front Bumper Lower Side Plate Replacement . 20-148
Rear Bumper Removal/Installation . 20-149
Rear Bumper Lower Cover Replacement . 20-151
...................................... ................................................
......................................
................................................
Hood Adjustment
. 20-152
Hood Seal Replacement . 20-153
Hood Insulator Replacement . 20-154
................................ ..............
..............
................................
..............
..............
Trunk Lid Adjustment
. 20-155
Trunk Lid Torsion Bar Replacement . 20-156
Trunk Lid Weatherstrip Replacement . 20-157
Trunk Lid Cushion Replacement . 20-157
.........................................
.........................
................
Fuel Fill Door Adjustment
. 20-158
Fuel Cap Adapter Replacement . 20-159
........................................
...............
.......................... ......................
...................... ...
..............
................
..................
..........................
..............
...............
.......................... ......................
...................... ...
..............
................
..................
Front Grille Replacement
. 20-160
Front Fender Trim Replacement . 20-162
Front Grille Cover Replacement . 20-163
Cowl Cover Replacement . 20-163
Roof Molding Replacement . 20-165
Door Molding Replacement . 20-167
Side Sill Protection Tape Replacement . 20-168
Rear License Trim Replacement . 20-168
Trunk Lid Spoiler Replacement . 20-169
Emblem/Sticker Replacement . 20-170 .............
...................... ............
......
.............
.............
......................... .................... .............
...................... ............
......
.............
.............
......................... ....................
Front Inner Fender Replacement . 20-171
Splash Shield Replacement
. 20-172
Front Fender Fairing Replacement . 20-173
Middle Floor Undercover Replacement . 20-174
Rear Floor Undercover Replacement . 20-174
Fuel Pipe Protector Replacement . 20-175
Rear Fender Cover Replacement . 20-175
Rear Strake Replacement . 20-176
Rear Air Outlet Replacement . 20-176
...................... ............
..................
..........................
........................................... .....
...................
......................
............
..................
..........................
........................................... .....
...................
Component Location Index
. 20-177
Hood Opener Cable Replacement . 20-178
Trunk Lid Opener Cable/Fuel Fill Door Opener Cable Replacement . 20-179
Hood Latch Replacement . 20-181
Trunk Lid Opener/Fuel Fill Door Opener Replacement . 20-182
Trunk Lid Lock Cylinder Replacement . 20-184
Trunk Lid Latch Replacement . 20-185
...........................................
........................................... ............................
...................................
...........................................
...........................................
............................
...................................
Upper Dashboard Support Gusset
Replacement . 20-186
Rear Floor Upper Cross-member Gusset Replacement . 20-186
Subframe Replacement . 20-187
Frame Repair Chart . 20-188
08/08/21 14:58:49 61SNR030_200_0003
ProCarManuals.com
DYNOMITE -2009-

Î
(#' )

S

pecial Tools Required
20-78 Interior Trim
Trim Removal/Installation - Rear Shelf Area
A F
astener Locations
: Clip
A
(White)
’06 model, 6
’07-09 models, 7
’06 model
’07-09 models A
A
A
A AAA
A
A
A
AA
A
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S
RS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:  Put on gloves to protect your hands.
 Take care not to bend or scratch the rear shelf or the trim.
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
1. Remove these items:  Rear seat cushion (see page 20-133)
 Rear seat-back (see page 20-131)
 Rear door opening seal, as needed (see step 3 onpage 20-68)
 C-pillar trim, both sides (see step 3 on page 20-75)
2. From the trunk compartment, disconnect the high mount brake light connector (A). 3.

From the trunk compartment, release the six or
seven white clips (A) by tapping on them.
08/08/21 15:01:36 61SNR030_200_0080
ProCarManuals.com
DYNOMITE -2009-



(#' )

S

pecial Tools Required
20-80 Interior Trim
Trim Removal/Installation - Trunk Area
Fastener Locations
: Clip, 2(White)
A A
F
astener Locations: Clip, 4(White)
A
B
A
KTC trim tool set SOJATP2014
NOTE:

Put on gloves to protect your hands.
 Take care not to bend or scratch the trim and panels.
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
1. Fold the rear seat-back forward.
2. Pull back the front portion of the spare tire lid (A), and detach the clips. 3

. Remove the spare tire lid (A).
4. Remove the trunk lid weatherstrip near the trunk rear trim panel.
5. Detach the clips, and release the hooks (A) by pulling the trunk rear trim panel (B) up, then
remove it.
08/08/21 15:01:37 61SNR030_200_0082
ProCarManuals.com
DYNOMITE -2009-


20-81
Fastener Locations
:Clip,3
A:Clip,2 B
A B
C
D E
C
A
A
B A
6. Remove the clips (A, B), then remove the trunk side
trim panel (C). Release the wire harness (D) from
the slit (E) in the trim panel. 7. If necessary, remove the trunk tool box (A).
8. Install the trim in the reverse order of removal, and
note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Push the clips into place securely.
08/08/21 15:01:37 61SNR030_200_0083
ProCarManuals.com
DYNOMITE -2009-


(#' )


(#'
 )
S

pecial Tools Required Special Tools Required
20-8220-82Interior Trim
Trim Removal/Installation - Trunk
Lid
Grab Handle Removal/Installation
Fastener Locations
:Clip,2
A
Fastener Locations:Clip,4
A : Clip, 4
B
A
B
C A
AA
B
B
B
A
B
A
A
C
B
C
A
KTC trim tool set SOJATP2014
NOTE:

Put on gloves to protect your hands.
 Take care not to bend or scratch the trim and panels.
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
1. Remove the clips from both trunk lid hinge cover (A), then remove the covers.
2. Remove the clips (A, B), then remove the trunk lid trim (C).
3. Install the trim in the reverse order of removal, and if the clips are damaged or stress-whitened, replace
them with new ones. KT

C trim tool set SOJATP2014
NOTE: Use the appropriate tool from the KTC trim tool
set to avoid damage when removing components. 1. Lower the grab handle (A), then pull out the stoppers (B).
2. While pinching the clips (A), release the hooks (B), then remove the grab handle (C).
08/08/21 15:01:38 61SNR030_200_0084
ProCarManuals.com
DYNOMITE -2009-




(#'

 )
20-13520-135
Rear Seat-back Latch Replacement
A
B
B
A
B
A
B
Fastener Locations
A
:Bolt,2
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
3. Fold the seat-back down.
4. Lift the seat side bolster (A) up to release the hook(B), then remove the seat side bolster.
5. Install the side bolster in the reverse order of removal, and note these items:
 Guide the belts over the front of the seat side bolster as you install the bolster.
 Before attaching the seat side bolster, make sure there are no twists or kinks in the seat belts. NOTE: Take care not to bend or scratch the interior trim.
1. Remove the rear shelf (see page 20-78).
2. From the trunk compartment, disconnect the seat- back release cable (A) from the seat-back latch (B).
3. Remove the bolts, then remove the seat-back latch (A).
(cont’d)
08/08/21 15:04:04 61SNR030_200_0137
ProCarManuals.com
DYNOMITE -2009-




(#'

 )
20-13520-135
Rear Seat-back Latch Replacement
A
B
B
A
B
A
B
Fastener Locations
A
:Bolt,2
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
3. Fold the seat-back down.
4. Lift the seat side bolster (A) up to release the hook(B), then remove the seat side bolster.
5. Install the side bolster in the reverse order of removal, and note these items:
 Guide the belts over the front of the seat side bolster as you install the bolster.
 Before attaching the seat side bolster, make sure there are no twists or kinks in the seat belts. NOTE: Take care not to bend or scratch the interior trim.
1. Remove the rear shelf (see page 20-78).
2. From the trunk compartment, disconnect the seat- back release cable (A) from the seat-back latch (B).
3. Remove the bolts, then remove the seat-back latch (A).
(cont’d)
08/08/21 15:04:04 61SNR030_200_0137
ProCarManuals.com
DYNOMITE -2009-